Commit | Line | Data |
---|---|---|
a8e93ed8 DB |
1 | # STK1000 customization |
2 | ||
3 | if BOARD_ATSTK1002 | |
4 | ||
5 | config BOARD_ATSTK1002_CUSTOM | |
6 | bool "Non-default STK-1002 jumper settings" | |
7 | help | |
8 | You will normally leave the jumpers on the CPU card at their | |
9 | default settings. If you need to use certain peripherals, | |
10 | you will need to change some of those jumpers. | |
11 | ||
12 | if BOARD_ATSTK1002_CUSTOM | |
13 | ||
14 | config BOARD_ATSTK1002_SW1_CUSTOM | |
15 | bool "SW1: use SSC1 (not SPI0)" | |
16 | help | |
17 | This also prevents using the external DAC as an audio interface, | |
18 | and means you can't initialize the on-board QVGA display. | |
19 | ||
20 | config BOARD_ATSTK1002_SW2_CUSTOM | |
21 | bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)" | |
22 | help | |
23 | If you change this you'll want an updated boot loader putting | |
24 | the console on UART-C not UART-A. | |
25 | ||
26 | config BOARD_ATSTK1002_SW3_CUSTOM | |
27 | bool "SW3: use TIMER1 (not SSC0 and GCLK)" | |
28 | help | |
29 | This also prevents using the external DAC as an audio interface. | |
30 | ||
31 | config BOARD_ATSTK1002_SW4_CUSTOM | |
32 | bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)" | |
33 | help | |
34 | To use the camera interface you'll need a custom card (on the | |
35 | PCI-format connector) connect a video sensor. | |
36 | ||
37 | config BOARD_ATSTK1002_SW5_CUSTOM | |
38 | bool "SW5: use MACB1 (not LCDC)" | |
39 | ||
40 | config BOARD_ATSTK1002_SW6_CUSTOM | |
41 | bool "SW6: more GPIOs (not MACB0)" | |
42 | ||
43 | endif # custom | |
44 | ||
45 | config BOARD_ATSTK1002_SPI1 | |
46 | bool "Configure SPI1 controller" | |
47 | depends on !BOARD_ATSTK1002_SW4_CUSTOM | |
48 | help | |
49 | All the signals for the second SPI controller are available on | |
50 | GPIO lines and accessed through the J1 jumper block. Say "y" | |
51 | here to configure that SPI controller. | |
52 | ||
ad93ab0a DB |
53 | config BOARD_ATSTK1002_J2_LED |
54 | bool | |
55 | default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB | |
56 | ||
57 | choice | |
58 | prompt "LEDs connected to J2:" | |
59 | depends on LEDS_GPIO && !BOARD_ATSTK1002_SW4_CUSTOM | |
60 | optional | |
61 | help | |
62 | Select this if you have jumpered the J2 jumper block to the | |
63 | LED0..LED7 amber leds, or to the RGB leds, using a ten-pin | |
64 | IDC cable. A default "heartbeat" trigger is provided, but | |
65 | you can of course override this. | |
66 | ||
67 | config BOARD_ATSTK1002_J2_LED8 | |
68 | bool "LED0..LED7" | |
69 | help | |
70 | Select this if J2 is jumpered to LED0..LED7 amber leds. | |
71 | ||
72 | config BOARD_ATSTK1002_J2_RGB | |
73 | bool "RGB leds" | |
74 | help | |
75 | Select this if J2 is jumpered to the RGB leds. | |
76 | ||
77 | endchoice | |
78 | ||
a8e93ed8 | 79 | endif # stk 1002 |