Commit | Line | Data |
---|---|---|
7c6ccbf0 IG |
1 | #ifndef __ASM_ARCH_PXA3xx_U2D_H |
2 | #define __ASM_ARCH_PXA3xx_U2D_H | |
3 | ||
4 | #include <mach/bitfield.h> | |
5 | ||
6 | /* | |
7 | * USB2 device controller registers and bits definitions | |
8 | */ | |
9 | #define U2DCR (0x0000) /* U2D Control Register */ | |
10 | #define U2DCR_NDC (1 << 31) /* NAK During Config */ | |
11 | #define U2DCR_HSTC (0x7 << 28) /* High Speed Timeout Calibration */ | |
12 | #define U2DCR_SPEOREN (1 << 27) /* Short Packet EOR INTR generation Enable */ | |
13 | #define U2DCR_FSTC (0x7 << 24) /* Full Speed Timeout Calibration */ | |
14 | #define U2DCR_UCLKOVR (1 << 22) /* UTM Clock Override */ | |
15 | #define U2DCR_ABP (1 << 21) /* Application Bus Power */ | |
16 | #define U2DCR_ADD (1 << 20) /* Application Device Disconnect */ | |
17 | #define U2DCR_CC (1 << 19) /* Configuration Change */ | |
18 | #define U2DCR_HS (1 << 18) /* High Speed USB Detection */ | |
19 | #define U2DCR_SMAC (1 << 17) /* Switch Endpoint Memory to Active Configuration */ | |
20 | #define U2DCR_DWRE (1 << 16) /* Device Remote Wake-up Feature */ | |
21 | #define U2DCR_ACN (0xf << 12) /* Active U2D Configuration Number */ | |
22 | #define U2DCR_AIN (0xf << 8) /* Active U2D Interface Number */ | |
23 | #define U2DCR_AAISN (0xf << 4) /* Active U2D Alternate Interface Setting Number */ | |
24 | #define U2DCR_EMCE (1 << 3) /* Endpoint Memory Configuration Error */ | |
25 | #define U2DCR_UDR (1 << 2) /* U2D Resume */ | |
26 | #define U2DCR_UDA (1 << 1) /* U2D Active */ | |
27 | #define U2DCR_UDE (1 << 0) /* U2D Enable */ | |
28 | ||
29 | #define U2DICR (0x0004) /* U2D Interrupt Control Register */ | |
30 | #define U2DISR (0x000C) /* U2D Interrupt Status Register */ | |
31 | #define U2DINT_CC (1 << 31) /* Interrupt - Configuration Change */ | |
32 | #define U2DINT_SOF (1 << 30) /* Interrupt - SOF */ | |
33 | #define U2DINT_USOF (1 << 29) /* Interrupt - micro SOF */ | |
34 | #define U2DINT_RU (1 << 28) /* Interrupt - Resume */ | |
35 | #define U2DINT_SU (1 << 27) /* Interrupt - Suspend */ | |
36 | #define U2DINT_RS (1 << 26) /* Interrupt - Reset */ | |
37 | #define U2DINT_DPE (1 << 25) /* Interrupt - Data Packet Error */ | |
38 | #define U2DINT_FIFOERR (0x4) /* Interrupt - endpoint FIFO error */ | |
39 | #define U2DINT_PACKETCMP (0x2) /* Interrupt - endpoint packet complete */ | |
40 | #define U2DINT_SPACKETCMP (0x1) /* Interrupt - endpoint short packet complete */ | |
41 | ||
42 | #define U2DFNR (0x0014) /* U2D Frame Number Register */ | |
43 | ||
44 | #define U2DINT(n, intr) (((intr) & 0x07) << (((n) & 0x07) * 3)) | |
45 | #define U2DICR2 (0x0008) /* U2D Interrupt Control Register 2 */ | |
46 | #define U2DISR2 (0x0010) /* U2D Interrupt Status Register 2 */ | |
47 | ||
48 | #define U2DOTGCR (0x0020) /* U2D OTG Control Register */ | |
49 | #define U2DOTGCR_OTGEN (1 << 31) /* On-The-Go Enable */ | |
50 | #define U2DOTGCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation Protocal Port Support */ | |
51 | #define U2DOTGCR_AHNP (1 << 29) /* A-device Host Negotiation Protocal Support */ | |
52 | #define U2DOTGCR_BHNP (1 << 28) /* B-device Host Negotiation Protocal Enable */ | |
53 | ||
54 | #ifdef CONFIG_CPU_PXA930 | |
55 | #define U2DOTGCR_LPA (1 << 15) /* ULPI low power mode active */ | |
56 | #define U2DOTGCR_IESI (1 << 13) /* OTG interrupt Enable */ | |
57 | #define U2DOTGCR_ISSI (1 << 12) /* OTG interrupt status */ | |
58 | #endif | |
59 | ||
60 | #define U2DOTGCR_CKAF (1 << 5) /* Carkit Mode Alternate Function Select */ | |
61 | #define U2DOTGCR_UTMID (1 << 4) /* UTMI Interface Disable */ | |
62 | #define U2DOTGCR_ULAF (1 << 3) /* ULPI Mode Alternate Function Select */ | |
63 | #define U2DOTGCR_SMAF (1 << 2) /* Serial Mode Alternate Function Select */ | |
64 | #define U2DOTGCR_RTSM (1 << 1) /* Return to Synchronous Mode (ULPI Mode) */ | |
65 | #define U2DOTGCR_ULE (1 << 0) /* ULPI Wrapper Enable */ | |
66 | ||
67 | #define U2DOTGICR (0x0024) /* U2D OTG Interrupt Control Register */ | |
68 | #define U2DOTGISR (0x0028) /* U2D OTG Interrupt Status Register */ | |
69 | ||
70 | #define U2DOTGINT_SF (1 << 17) /* OTG Set Feature Command Received */ | |
71 | #define U2DOTGINT_SI (1 << 16) /* OTG Interrupt */ | |
72 | #define U2DOTGINT_RLS1 (1 << 14) /* RXCMD Linestate[1] Change Interrupt Rise */ | |
73 | #define U2DOTGINT_RLS0 (1 << 13) /* RXCMD Linestate[0] Change Interrupt Rise */ | |
74 | #define U2DOTGINT_RID (1 << 12) /* RXCMD OTG ID Change Interrupt Rise */ | |
75 | #define U2DOTGINT_RSE (1 << 11) /* RXCMD OTG Session End Interrupt Rise */ | |
76 | #define U2DOTGINT_RSV (1 << 10) /* RXCMD OTG Session Valid Interrupt Rise */ | |
77 | #define U2DOTGINT_RVV (1 << 9) /* RXCMD OTG Vbus Valid Interrupt Rise */ | |
78 | #define U2DOTGINT_RCK (1 << 8) /* RXCMD Carkit Interrupt Rise */ | |
79 | #define U2DOTGINT_FLS1 (1 << 6) /* RXCMD Linestate[1] Change Interrupt Fall */ | |
80 | #define U2DOTGINT_FLS0 (1 << 5) /* RXCMD Linestate[0] Change Interrupt Fall */ | |
81 | #define U2DOTGINT_FID (1 << 4) /* RXCMD OTG ID Change Interrupt Fall */ | |
82 | #define U2DOTGINT_FSE (1 << 3) /* RXCMD OTG Session End Interrupt Fall */ | |
83 | #define U2DOTGINT_FSV (1 << 2) /* RXCMD OTG Session Valid Interrupt Fall */ | |
84 | #define U2DOTGINT_FVV (1 << 1) /* RXCMD OTG Vbus Valid Interrupt Fall */ | |
85 | #define U2DOTGINT_FCK (1 << 0) /* RXCMD Carkit Interrupt Fall */ | |
86 | ||
87 | #define U2DOTGUSR (0x002C) /* U2D OTG ULPI Status Register */ | |
88 | #define U2DOTGUSR_LPA (1 << 31) /* ULPI Low Power Mode Active */ | |
89 | #define U2DOTGUSR_S6A (1 << 30) /* ULPI Serial Mode (6-pin) Active */ | |
90 | #define U2DOTGUSR_S3A (1 << 29) /* ULPI Serial Mode (3-pin) Active */ | |
91 | #define U2DOTGUSR_CKA (1 << 28) /* ULPI Car Kit Mode Active */ | |
92 | #define U2DOTGUSR_LS1 (1 << 6) /* RXCMD Linestate 1 Status */ | |
93 | #define U2DOTGUSR_LS0 (1 << 5) /* RXCMD Linestate 0 Status */ | |
94 | #define U2DOTGUSR_ID (1 << 4) /* OTG IDGnd Status */ | |
95 | #define U2DOTGUSR_SE (1 << 3) /* OTG Session End Status */ | |
96 | #define U2DOTGUSR_SV (1 << 2) /* OTG Session Valid Status */ | |
97 | #define U2DOTGUSR_VV (1 << 1) /* OTG Vbus Valid Status */ | |
98 | #define U2DOTGUSR_CK (1 << 0) /* Carkit Interrupt Status */ | |
99 | ||
100 | #define U2DOTGUCR (0x0030) /* U2D OTG ULPI Control Register */ | |
101 | #define U2DOTGUCR_RUN (1 << 25) /* RUN */ | |
102 | #define U2DOTGUCR_RNW (1 << 24) /* Read or Write operation */ | |
103 | #define U2DOTGUCR_ADDR (0x3f << 16) /* Address of the ULPI PHY register */ | |
104 | #define U2DOTGUCR_WDATA (0xff << 8) /* The data for a WRITE command */ | |
105 | #define U2DOTGUCR_RDATA (0xff << 0) /* The data for a READ command */ | |
106 | ||
107 | #define U2DP3CR (0x0034) /* U2D Port 3 Control Register */ | |
108 | #define U2DP3CR_P2SS (0x3 << 8) /* Host Port 2 Serial Mode Select */ | |
109 | #define U2DP3CR_P3SS (0x7 << 4) /* Host Port 3 Serial Mode Select */ | |
110 | #define U2DP3CR_VPVMBEN (0x1 << 2) /* Host Port 3 Vp/Vm Block Enable */ | |
111 | #define U2DP3CR_CFG (0x3 << 0) /* Host Port 3 Configuration */ | |
112 | ||
113 | #define U2DCSR0 (0x0100) /* U2D Control/Status Register - Endpoint 0 */ | |
114 | #define U2DCSR0_IPA (1 << 8) /* IN Packet Adjusted */ | |
115 | #define U2DCSR0_SA (1 << 7) /* SETUP Active */ | |
116 | #define U2DCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ | |
117 | #define U2DCSR0_FST (1 << 5) /* Force Stall */ | |
118 | #define U2DCSR0_SST (1 << 4) /* Send Stall */ | |
119 | #define U2DCSR0_DME (1 << 3) /* DMA Enable */ | |
120 | #define U2DCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ | |
121 | #define U2DCSR0_IPR (1 << 1) /* IN Packet Ready */ | |
122 | #define U2DCSR0_OPC (1 << 0) /* OUT Packet Complete */ | |
123 | ||
124 | #define U2DCSR(x) (0x0100 + ((x) << 2)) /* U2D Control/Status Register - Endpoint x */ | |
125 | #define U2DCSR_BF (1 << 10) /* Buffer Full, for OUT eps */ | |
126 | #define U2DCSR_BE (1 << 10) /* Buffer Empty, for IN eps */ | |
127 | #define U2DCSR_DPE (1 << 9) /* Data Packet Error, for ISO eps only */ | |
128 | #define U2DCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ | |
129 | #define U2DCSR_SP (1 << 7) /* Short Packet Control/Status, for OUT eps only, readonly */ | |
130 | #define U2DCSR_BNE (1 << 6) /* Buffer Not Empty, for OUT eps */ | |
131 | #define U2DCSR_BNF (1 << 6) /* Buffer Not Full, for IN eps */ | |
132 | #define U2DCSR_FST (1 << 5) /* Force STALL, write 1 set */ | |
133 | #define U2DCSR_SST (1 << 4) /* Sent STALL, write 1 clear */ | |
134 | #define U2DCSR_DME (1 << 3) /* DMA Enable */ | |
135 | #define U2DCSR_TRN (1 << 2) /* Tx/Rx NAK, write 1 clear */ | |
136 | #define U2DCSR_PC (1 << 1) /* Packet Complete, write 1 clear */ | |
137 | #define U2DCSR_FS (1 << 0) /* FIFO needs Service */ | |
138 | ||
139 | #define U2DBCR0 (0x0200) /* U2D Byte Count Register - Endpoint 0 */ | |
140 | #define U2DBCR(x) (0x0200 + ((x) << 2)) /* U2D Byte Count Register - Endpoint x */ | |
141 | ||
142 | #define U2DDR0 (0x0300) /* U2D Data Register - Endpoint 0 */ | |
143 | ||
144 | #define U2DEPCR(x) (0x0400 + ((x) << 2)) /* U2D Configuration Register - Endpoint x */ | |
145 | #define U2DEPCR_EE (1 << 0) /* Endpoint Enable */ | |
146 | #define U2DEPCR_BS_MASK (0x3FE) /* Buffer Size, BS*8=FIFO size, max 8184B = 8KB */ | |
147 | ||
148 | #define U2DSCA (0x0500) /* U2D Setup Command Address */ | |
149 | #define U2DSCA_VALUE (0x0120) | |
150 | ||
151 | #define U2DEN0 (0x0504) /* U2D Endpoint Information Register - Endpoint 0 */ | |
152 | #define U2DEN(x) (0x0504 + ((x) << 2)) /* U2D Endpoint Information Register - Endpoint x */ | |
153 | ||
154 | /* U2DMA registers */ | |
155 | #define U2DMACSR0 (0x1000) /* U2DMA Control/Status Register - Channel 0 */ | |
156 | #define U2DMACSR(x) (0x1000 + ((x) << 2)) /* U2DMA Control/Status Register - Channel x */ | |
157 | #define U2DMACSR_RUN (1 << 31) /* Run Bit (read / write) */ | |
158 | #define U2DMACSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */ | |
159 | #define U2DMACSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */ | |
160 | #define U2DMACSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */ | |
161 | #define U2DMACSR_EORSTOPEN (1 << 26) /* STOP on an EOR */ | |
162 | #define U2DMACSR_RASIRQEN (1 << 23) /* Request After Cnannel Stopped Interrupt Enable */ | |
163 | #define U2DMACSR_MASKRUN (1 << 22) /* Mask Run */ | |
164 | #define U2DMACSR_SCEMC (3 << 18) /* System Bus Split Completion Error Message Class */ | |
165 | #define U2DMACSR_SCEMI (0x1f << 13) /* System Bus Split Completion Error Message Index */ | |
166 | #define U2DMACSR_BUSERRTYPE (7 << 10) /* PX Bus Error Type */ | |
167 | #define U2DMACSR_EORINTR (1 << 9) /* End Of Receive */ | |
168 | #define U2DMACSR_REQPEND (1 << 8) /* Request Pending */ | |
169 | #define U2DMACSR_RASINTR (1 << 4) /* Request After Channel Stopped (read / write 1 clear) */#define U2DMACSR_STOPINTR (1 << 3) /* Stop Interrupt (read only) */ | |
170 | #define U2DMACSR_ENDINTR (1 << 2) /* End Interrupt (read / write 1 clear) */ | |
171 | #define U2DMACSR_STARTINTR (1 << 1) /* Start Interrupt (read / write 1 clear) */ | |
172 | #define U2DMACSR_BUSERRINTR (1 << 0) /* Bus Error Interrupt (read / write 1 clear) */ | |
173 | ||
174 | #define U2DMACR (0x1080) /* U2DMA Control Register */ | |
175 | #define U2DMAINT (0x10F0) /* U2DMA Interrupt Register */ | |
176 | ||
177 | #define U2DMABR0 (0x1100) /* U2DMA Branch Register - Channel 0 */ | |
178 | #define U2DMABR(x) (0x1100 + (x) << 2) /* U2DMA Branch Register - Channel x */ | |
179 | ||
180 | #define U2DMADADR0 (0x1200) /* U2DMA Descriptor Address Register - Channel 0 */ | |
181 | #define U2DMADADR(x) (0x1200 + (x) * 0x10) /* U2DMA Descriptor Address Register - Channel x */ | |
182 | ||
183 | #define U2DMADADR_STOP (1U << 0) | |
184 | ||
185 | #define U2DMASADR0 (0x1204) /* U2DMA Source Address Register - Channel 0 */ | |
186 | #define U2DMASADR(x) (0x1204 + (x) * 0x10) /* U2DMA Source Address Register - Channel x */ | |
187 | #define U2DMATADR0 (0x1208) /* U2DMA Target Address Register - Channel 0 */ | |
188 | #define U2DMATADR(x) (0x1208 + (x) * 0x10) /* U2DMA Target Address Register - Channel x */ | |
189 | ||
190 | #define U2DMACMDR0 (0x120C) /* U2DMA Command Address Register - Channel 0 */ | |
191 | #define U2DMACMDR(x) (0x120C + (x) * 0x10) /* U2DMA Command Address Register - Channel x */ | |
192 | ||
193 | #define U2DMACMDR_XFRDIS (1 << 31) /* Transfer Direction */ | |
194 | #define U2DMACMDR_STARTIRQEN (1 << 22) /* Start Interrupt Enable */ | |
195 | #define U2DMACMDR_ENDIRQEN (1 << 21) /* End Interrupt Enable */ | |
196 | #define U2DMACMDR_PACKCOMP (1 << 13) /* Packet Complete */ | |
197 | #define U2DMACMDR_LEN (0x07ff) /* length mask (max = 2K - 1) */ | |
198 | ||
199 | #endif /* __ASM_ARCH_PXA3xx_U2D_H */ |