[linux-2.6-block.git] / arch / arm / mach-orion5x / kurobox_pro-setup.c

/*
 * arch/arm/mach-orion5x/kurobox_pro-setup.c
 *
 * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
 *
 * This file is licensed under the terms of the GNU General Public
 * License version 2.  This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/nand.h>
#include <linux/mv643xx_eth.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include <plat/orion_nand.h>
#include "common.h"
#include "mpp.h"

/*****************************************************************************
 * KUROBOX-PRO Info
 ****************************************************************************/

/*
 * 256K NOR flash Device bus boot chip select
 */

#define KUROBOX_PRO_NOR_BOOT_BASE	0xf4000000
#define KUROBOX_PRO_NOR_BOOT_SIZE	SZ_256K

/*
 * 256M NAND flash on Device bus chip select 1
 */

#define KUROBOX_PRO_NAND_BASE		0xfc000000
#define KUROBOX_PRO_NAND_SIZE		SZ_2M

/*****************************************************************************
 * 256MB NAND Flash on Device bus CS0
 ****************************************************************************/

static struct mtd_partition kurobox_pro_nand_parts[] = {
	{
		.name	= "uImage",
		.offset	= 0,
		.size	= SZ_4M,
	}, {
		.name	= "rootfs",
		.offset	= SZ_4M,
		.size	= SZ_64M,
	}, {
		.name	= "extra",
		.offset	= SZ_4M + SZ_64M,
		.size	= SZ_256M - (SZ_4M + SZ_64M),
	},
};

static struct resource kurobox_pro_nand_resource = {
	.flags		= IORESOURCE_MEM,
	.start		= KUROBOX_PRO_NAND_BASE,
	.end		= KUROBOX_PRO_NAND_BASE + KUROBOX_PRO_NAND_SIZE - 1,
};

static struct orion_nand_data kurobox_pro_nand_data = {
	.parts		= kurobox_pro_nand_parts,
	.nr_parts	= ARRAY_SIZE(kurobox_pro_nand_parts),
	.cle		= 0,
	.ale		= 1,
	.width		= 8,
};

static struct platform_device kurobox_pro_nand_flash = {
	.name		= "orion_nand",
	.id		= -1,
	.dev		= {
		.platform_data	= &kurobox_pro_nand_data,
	},
	.resource	= &kurobox_pro_nand_resource,
	.num_resources	= 1,
};

/*****************************************************************************
 * 256KB NOR Flash on BOOT Device
 ****************************************************************************/

static struct physmap_flash_data kurobox_pro_nor_flash_data = {
	.width		= 1,
};

static struct resource kurobox_pro_nor_flash_resource = {
	.flags			= IORESOURCE_MEM,
	.start			= KUROBOX_PRO_NOR_BOOT_BASE,
	.end			= KUROBOX_PRO_NOR_BOOT_BASE + KUROBOX_PRO_NOR_BOOT_SIZE - 1,
};

static struct platform_device kurobox_pro_nor_flash = {
	.name			= "physmap-flash",
	.id			= 0,
	.dev		= {
		.platform_data	= &kurobox_pro_nor_flash_data,
	},
	.num_resources		= 1,
	.resource		= &kurobox_pro_nor_flash_resource,
};

/*****************************************************************************
 * PCI
 ****************************************************************************/

static int __init kurobox_pro_pci_map_irq(const struct pci_dev *dev, u8 slot,
	u8 pin)
{
	int irq;

	/*
	 * Check for devices with hard-wired IRQs.
	 */
	irq = orion5x_pci_map_irq(dev, slot, pin);
	if (irq != -1)
		return irq;

	/*
	 * PCI isn't used on the Kuro
	 */
	return -1;
}

static struct hw_pci kurobox_pro_pci __initdata = {
	.nr_controllers	= 2,
	.swizzle	= pci_std_swizzle,
	.setup		= orion5x_pci_sys_setup,
	.scan		= orion5x_pci_sys_scan_bus,
	.map_irq	= kurobox_pro_pci_map_irq,
};

static int __init kurobox_pro_pci_init(void)
{
	if (machine_is_kurobox_pro()) {
		orion5x_pci_disable();
		pci_common_init(&kurobox_pro_pci);
	}

	return 0;
}

subsys_initcall(kurobox_pro_pci_init);

/*****************************************************************************
 * Ethernet
 ****************************************************************************/

static struct mv643xx_eth_platform_data kurobox_pro_eth_data = {
	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
};

/*****************************************************************************
 * RTC 5C372a on I2C bus
 ****************************************************************************/
static struct i2c_board_info __initdata kurobox_pro_i2c_rtc = {
	I2C_BOARD_INFO("rs5c372a", 0x32),
};

/*****************************************************************************
 * SATA
 ****************************************************************************/
static struct mv_sata_platform_data kurobox_pro_sata_data = {
	.n_ports	= 2,
};

/*****************************************************************************
 * Kurobox Pro specific power off method via UART1-attached microcontroller
 ****************************************************************************/

#define UART1_REG(x)	(UART1_VIRT_BASE + ((UART_##x) << 2))

static int kurobox_pro_miconread(unsigned char *buf, int count)
{
	int i;
	int timeout;

	for (i = 0; i < count; i++) {
		timeout = 10;

		while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
			if (--timeout == 0)
				break;
			udelay(1000);
		}

		if (timeout == 0)
			break;
		buf[i] = readl(UART1_REG(RX));
	}

	/* return read bytes */
	return i;
}

static int kurobox_pro_miconwrite(const unsigned char *buf, int count)
{
	int i = 0;

	while (count--) {
		while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
			barrier();
		writel(buf[i++], UART1_REG(TX));
	}

	return 0;
}

static int kurobox_pro_miconsend(const unsigned char *data, int count)
{
	int i;
	unsigned char checksum = 0;
	unsigned char recv_buf[40];
	unsigned char send_buf[40];
	unsigned char correct_ack[3];
	int retry = 2;

	/* Generate checksum */
	for (i = 0; i < count; i++)
		checksum -=  data[i];

	do {
		/* Send data */
		kurobox_pro_miconwrite(data, count);

		/* send checksum */
		kurobox_pro_miconwrite(&checksum, 1);

		if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
			printk(KERN_ERR ">%s: receive failed.\n", __func__);

			/* send preamble to clear the receive buffer */
			memset(&send_buf, 0xff, sizeof(send_buf));
			kurobox_pro_miconwrite(send_buf, sizeof(send_buf));

			/* make dummy reads */
			mdelay(100);
			kurobox_pro_miconread(recv_buf, sizeof(recv_buf));
		} else {
			/* Generate expected ack */
			correct_ack[0] = 0x01;
			correct_ack[1] = data[1];
			correct_ack[2] = 0x00;

			/* checksum Check */
			if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
			     recv_buf[3]) & 0xFF) {
				printk(KERN_ERR ">%s: Checksum Error : "
					"Received data[%02x, %02x, %02x, %02x]"
					"\n", __func__, recv_buf[0],
					recv_buf[1], recv_buf[2], recv_buf[3]);
			} else {
				/* Check Received Data */
				if (correct_ack[0] == recv_buf[0] &&
				    correct_ack[1] == recv_buf[1] &&
				    correct_ack[2] == recv_buf[2]) {
					/* Interval for next command */
					mdelay(10);

					/* Receive ACK */
					return 0;
				}
			}
			/* Received NAK or illegal Data */
			printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
					"Received\n", __func__);
		}
	} while (retry--);

	/* Interval for next command */
	mdelay(10);

	return -1;
}

static void kurobox_pro_power_off(void)
{
	const unsigned char watchdogkill[]	= {0x01, 0x35, 0x00};
	const unsigned char shutdownwait[]	= {0x00, 0x0c};
	const unsigned char poweroff[]		= {0x00, 0x06};
	/* 38400 baud divisor */
	const unsigned divisor = ((orion5x_tclk + (8 * 38400)) / (16 * 38400));

	pr_info("%s: triggering power-off...\n", __func__);

	/* hijack uart1 and reset into sane state (38400,8n1,even parity) */
	writel(0x83, UART1_REG(LCR));
	writel(divisor & 0xff, UART1_REG(DLL));
	writel((divisor >> 8) & 0xff, UART1_REG(DLM));
	writel(0x1b, UART1_REG(LCR));
	writel(0x00, UART1_REG(IER));
	writel(0x07, UART1_REG(FCR));
	writel(0x00, UART1_REG(MCR));

	/* Send the commands to shutdown the Kurobox Pro */
	kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ;
	kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ;
	kurobox_pro_miconsend(poweroff, sizeof(poweroff));
}

/*****************************************************************************
 * General Setup
 ****************************************************************************/
static unsigned int kurobox_pro_mpp_modes[] __initdata = {
	MPP0_UNUSED,
	MPP1_UNUSED,
	MPP2_GPIO,		/* GPIO Micon */
	MPP3_GPIO,		/* GPIO Rtc */
	MPP4_UNUSED,
	MPP5_UNUSED,
	MPP6_NAND,		/* NAND Flash REn */
	MPP7_NAND,		/* NAND Flash WEn */
	MPP8_UNUSED,
	MPP9_UNUSED,
	MPP10_UNUSED,
	MPP11_UNUSED,
	MPP12_SATA_LED,		/* SATA 0 presence */
	MPP13_SATA_LED,		/* SATA 1 presence */
	MPP14_SATA_LED,		/* SATA 0 active */
	MPP15_SATA_LED,		/* SATA 1 active */
	MPP16_UART,		/* UART1 RXD */
	MPP17_UART,		/* UART1 TXD */
	MPP18_UART,		/* UART1 CTSn */
	MPP19_UART,		/* UART1 RTSn */
	0,
};

static void __init kurobox_pro_init(void)
{
	/*
	 * Setup basic Orion functions. Need to be called early.
	 */
	orion5x_init();

	orion5x_mpp_conf(kurobox_pro_mpp_modes);

	/*
	 * Configure peripherals.
	 */
	orion5x_ehci0_init();
	orion5x_ehci1_init();
	orion5x_eth_init(&kurobox_pro_eth_data);
	orion5x_i2c_init();
	orion5x_sata_init(&kurobox_pro_sata_data);
	orion5x_uart0_init();
	orion5x_uart1_init();
	orion5x_xor_init();

	orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
				   KUROBOX_PRO_NOR_BOOT_SIZE);
	platform_device_register(&kurobox_pro_nor_flash);

	if (machine_is_kurobox_pro()) {
		orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE,
				       KUROBOX_PRO_NAND_SIZE);
		platform_device_register(&kurobox_pro_nand_flash);
	}

	i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);

	/* register Kurobox Pro specific power-off method */
	pm_power_off = kurobox_pro_power_off;
}

#ifdef CONFIG_MACH_KUROBOX_PRO
MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro")
	/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
	.boot_params	= 0x00000100,
	.init_machine	= kurobox_pro_init,
	.map_io		= orion5x_map_io,
	.init_early	= orion5x_init_early,
	.init_irq	= orion5x_init_irq,
	.timer		= &orion5x_timer,
	.fixup		= tag_fixup_mem32,
MACHINE_END
#endif

#ifdef CONFIG_MACH_LINKSTATION_PRO
MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live")
	/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
	.boot_params	= 0x00000100,
	.init_machine	= kurobox_pro_init,
	.map_io		= orion5x_map_io,
	.init_early	= orion5x_init_early,
	.init_irq	= orion5x_init_irq,
	.timer		= &orion5x_timer,
	.fixup		= tag_fixup_mem32,
MACHINE_END
#endif
Commit	Line	Data
1e780453	1	/*
9dd0b194	2	* arch/arm/mach-orion5x/kurobox_pro-setup.c
1e780453 RS	3	*
	4	* Maintainer: Ronen Shitrit <rshitrit@marvell.com>
	5	*
159ffb3a LB	6	* This file is licensed under the terms of the GNU General Public
159ffb3a LB	7	* License version 2. This program is licensed "as is" without any
1e780453 RS	8	* warranty of any kind, whether express or implied.
	9	*/
	10
	11	#include <linux/kernel.h>
	12	#include <linux/init.h>
	13	#include <linux/platform_device.h>
	14	#include <linux/pci.h>
	15	#include <linux/irq.h>
a0087f2f	16	#include <linux/delay.h>
1e780453 RS	17	#include <linux/mtd/physmap.h>
	18	#include <linux/mtd/nand.h>
	19	#include <linux/mv643xx_eth.h>
	20	#include <linux/i2c.h>
a0087f2f	21	#include <linux/serial_reg.h>
3b277c29	22	#include <linux/ata_platform.h>
1e780453 RS	23	#include <asm/mach-types.h>
	24	#include <asm/gpio.h>
	25	#include <asm/mach/arch.h>
	26	#include <asm/mach/pci.h>
a09e64fb	27	#include <mach/orion5x.h>
6f088f1d	28	#include <plat/orion_nand.h>
1e780453	29	#include "common.h"
19cfd5c0	30	#include "mpp.h"
1e780453 RS	31
	32	/*****************************************************************************
	33	* KUROBOX-PRO Info
	34	****************************************************************************/
	35
	36	/*
	37	* 256K NOR flash Device bus boot chip select
	38	*/
	39
	40	#define KUROBOX_PRO_NOR_BOOT_BASE 0xf4000000
	41	#define KUROBOX_PRO_NOR_BOOT_SIZE SZ_256K
	42
	43	/*
	44	* 256M NAND flash on Device bus chip select 1
	45	*/
	46
	47	#define KUROBOX_PRO_NAND_BASE 0xfc000000
	48	#define KUROBOX_PRO_NAND_SIZE SZ_2M
	49
	50	/*****************************************************************************
	51	* 256MB NAND Flash on Device bus CS0
	52	****************************************************************************/
	53
	54	static struct mtd_partition kurobox_pro_nand_parts[] = {
	55	{
	56	.name = "uImage",
	57	.offset = 0,
	58	.size = SZ_4M,
e7068ad3	59	}, {
1e780453 RS	60	.name = "rootfs",
	61	.offset = SZ_4M,
	62	.size = SZ_64M,
e7068ad3	63	}, {
1e780453 RS	64	.name = "extra",
	65	.offset = SZ_4M + SZ_64M,
	66	.size = SZ_256M - (SZ_4M + SZ_64M),
	67	},
	68	};
	69
	70	static struct resource kurobox_pro_nand_resource = {
	71	.flags = IORESOURCE_MEM,
	72	.start = KUROBOX_PRO_NAND_BASE,
	73	.end = KUROBOX_PRO_NAND_BASE + KUROBOX_PRO_NAND_SIZE - 1,
	74	};
	75
	76	static struct orion_nand_data kurobox_pro_nand_data = {
	77	.parts = kurobox_pro_nand_parts,
	78	.nr_parts = ARRAY_SIZE(kurobox_pro_nand_parts),
	79	.cle = 0,
	80	.ale = 1,
	81	.width = 8,
	82	};
	83
	84	static struct platform_device kurobox_pro_nand_flash = {
	85	.name = "orion_nand",
	86	.id = -1,
	87	.dev = {
	88	.platform_data = &kurobox_pro_nand_data,
	89	},
	90	.resource = &kurobox_pro_nand_resource,
	91	.num_resources = 1,
	92	};
	93
	94	/*****************************************************************************
	95	* 256KB NOR Flash on BOOT Device
	96	****************************************************************************/
	97
	98	static struct physmap_flash_data kurobox_pro_nor_flash_data = {
	99	.width = 1,
	100	};
	101
	102	static struct resource kurobox_pro_nor_flash_resource = {
	103	.flags = IORESOURCE_MEM,
	104	.start = KUROBOX_PRO_NOR_BOOT_BASE,
	105	.end = KUROBOX_PRO_NOR_BOOT_BASE + KUROBOX_PRO_NOR_BOOT_SIZE - 1,
	106	};
	107
	108	static struct platform_device kurobox_pro_nor_flash = {
	109	.name = "physmap-flash",
	110	.id = 0,
	111	.dev = {
	112	.platform_data = &kurobox_pro_nor_flash_data,
	113	},
	114	.num_resources = 1,
	115	.resource = &kurobox_pro_nor_flash_resource,
	116	};
	117
	118	/*****************************************************************************
	119	* PCI
	120	****************************************************************************/
	121
d5341942 RB	122	static int __init kurobox_pro_pci_map_irq(const struct pci_dev *dev, u8 slot,
d5341942 RB	123	u8 pin)
1e780453	124	{
92b913b0 LB	125	int irq;
	126
	127	/*
	128	* Check for devices with hard-wired IRQs.
	129	*/
	130	irq = orion5x_pci_map_irq(dev, slot, pin);
	131	if (irq != -1)
	132	return irq;
	133
1e780453 RS	134	/*
	135	* PCI isn't used on the Kuro
	136	*/
1e780453 RS	137	return -1;
	138	}
	139
	140	static struct hw_pci kurobox_pro_pci __initdata = {
bbdf1c1e	141	.nr_controllers = 2,
1e780453	142	.swizzle = pci_std_swizzle,
9dd0b194 LB	143	.setup = orion5x_pci_sys_setup,
9dd0b194 LB	144	.scan = orion5x_pci_sys_scan_bus,
1e780453 RS	145	.map_irq = kurobox_pro_pci_map_irq,
	146	};
	147
	148	static int __init kurobox_pro_pci_init(void)
	149	{
7a6bb262 PA	150	if (machine_is_kurobox_pro()) {
7a6bb262 PA	151	orion5x_pci_disable();
1e780453	152	pci_common_init(&kurobox_pro_pci);
7a6bb262	153	}
1e780453 RS	154
	155	return 0;
	156	}
	157
	158	subsys_initcall(kurobox_pro_pci_init);
	159
	160	/*****************************************************************************
	161	* Ethernet
	162	****************************************************************************/
	163
	164	static struct mv643xx_eth_platform_data kurobox_pro_eth_data = {
ac840605	165	.phy_addr = MV643XX_ETH_PHY_ADDR(8),
1e780453 RS	166	};
	167
	168	/*****************************************************************************
	169	* RTC 5C372a on I2C bus
	170	****************************************************************************/
	171	static struct i2c_board_info __initdata kurobox_pro_i2c_rtc = {
3760f736	172	I2C_BOARD_INFO("rs5c372a", 0x32),
1e780453 RS	173	};
1e780453 RS	174
3b277c29 BB	175	/*****************************************************************************
	176	* SATA
	177	****************************************************************************/
	178	static struct mv_sata_platform_data kurobox_pro_sata_data = {
e7068ad3	179	.n_ports = 2,
3b277c29 BB	180	};
3b277c29 BB	181
a0087f2f SB	182	/*****************************************************************************
	183	* Kurobox Pro specific power off method via UART1-attached microcontroller
	184	****************************************************************************/
	185
	186	#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2))
	187
	188	static int kurobox_pro_miconread(unsigned char *buf, int count)
	189	{
	190	int i;
	191	int timeout;
	192
	193	for (i = 0; i < count; i++) {
	194	timeout = 10;
	195
	196	while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
	197	if (--timeout == 0)
	198	break;
	199	udelay(1000);
	200	}
	201
	202	if (timeout == 0)
	203	break;
	204	buf[i] = readl(UART1_REG(RX));
	205	}
	206
	207	/* return read bytes */
	208	return i;
	209	}
	210
	211	static int kurobox_pro_miconwrite(const unsigned char *buf, int count)
	212	{
	213	int i = 0;
	214
	215	while (count--) {
	216	while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
	217	barrier();
	218	writel(buf[i++], UART1_REG(TX));
	219	}
	220
	221	return 0;
	222	}
	223
	224	static int kurobox_pro_miconsend(const unsigned char *data, int count)
	225	{
	226	int i;
	227	unsigned char checksum = 0;
	228	unsigned char recv_buf[40];
	229	unsigned char send_buf[40];
	230	unsigned char correct_ack[3];
	231	int retry = 2;
	232
	233	/* Generate checksum */
	234	for (i = 0; i < count; i++)
	235	checksum -= data[i];
	236
	237	do {
	238	/* Send data */
	239	kurobox_pro_miconwrite(data, count);
	240
	241	/* send checksum */
	242	kurobox_pro_miconwrite(&checksum, 1);
	243
	244	if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
	245	printk(KERN_ERR ">%s: receive failed.\n", __func__);
246
247	/* send preamble to clear the receive buffer */
248	memset(&send_buf, 0xff, sizeof(send_buf));
249	kurobox_pro_miconwrite(send_buf, sizeof(send_buf));
250
251	/* make dummy reads */
252	mdelay(100);
253	kurobox_pro_miconread(recv_buf, sizeof(recv_buf));
254	} else {
255	/* Generate expected ack */
256	correct_ack[0] = 0x01;
257	correct_ack[1] = data[1];
258	correct_ack[2] = 0x00;
259
260	/* checksum Check */
261	if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
262	recv_buf[3]) & 0xFF) {
263	printk(KERN_ERR ">%s: Checksum Error : "
264	"Received data[%02x, %02x, %02x, %02x]"
265	"\n", __func__, recv_buf[0],
266	recv_buf[1], recv_buf[2], recv_buf[3]);
267	} else {
268	/* Check Received Data */
269	if (correct_ack[0] == recv_buf[0] &&
270	correct_ack[1] == recv_buf[1] &&
271	correct_ack[2] == recv_buf[2]) {
272	/* Interval for next command */
273	mdelay(10);
274
275	/* Receive ACK */
276	return 0;
277	}
278	}
279	/* Received NAK or illegal Data */
280	printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
281	"Received\n", __func__);
282	}
283	} while (retry--);
284
285	/* Interval for next command */
286	mdelay(10);
287
288	return -1;
289	}
290
291	static void kurobox_pro_power_off(void)
292	{
293	const unsigned char watchdogkill[] = {0x01, 0x35, 0x00};
294	const unsigned char shutdownwait[] = {0x00, 0x0c};
295	const unsigned char poweroff[] = {0x00, 0x06};
296	/* 38400 baud divisor */
ebe35aff	297	const unsigned divisor = ((orion5x_tclk + (8 * 38400)) / (16 * 38400));
a0087f2f SB	298
	299	pr_info("%s: triggering power-off...\n", __func__);
	300
	301	/* hijack uart1 and reset into sane state (38400,8n1,even parity) */
	302	writel(0x83, UART1_REG(LCR));
	303	writel(divisor & 0xff, UART1_REG(DLL));
	304	writel((divisor >> 8) & 0xff, UART1_REG(DLM));
	305	writel(0x1b, UART1_REG(LCR));
	306	writel(0x00, UART1_REG(IER));
	307	writel(0x07, UART1_REG(FCR));
	308	writel(0x00, UART1_REG(MCR));
	309
	310	/* Send the commands to shutdown the Kurobox Pro */
	311	kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ;
	312	kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ;
	313	kurobox_pro_miconsend(poweroff, sizeof(poweroff));
	314	}
	315
1e780453 RS	316	/*****************************************************************************
	317	* General Setup
	318	****************************************************************************/
554cdaef AL	319	static unsigned int kurobox_pro_mpp_modes[] __initdata = {
	320	MPP0_UNUSED,
	321	MPP1_UNUSED,
	322	MPP2_GPIO, /* GPIO Micon */
	323	MPP3_GPIO, /* GPIO Rtc */
	324	MPP4_UNUSED,
	325	MPP5_UNUSED,
	326	MPP6_NAND, /* NAND Flash REn */
	327	MPP7_NAND, /* NAND Flash WEn */
	328	MPP8_UNUSED,
	329	MPP9_UNUSED,
	330	MPP10_UNUSED,
	331	MPP11_UNUSED,
	332	MPP12_SATA_LED, /* SATA 0 presence */
	333	MPP13_SATA_LED, /* SATA 1 presence */
	334	MPP14_SATA_LED, /* SATA 0 active */
	335	MPP15_SATA_LED, /* SATA 1 active */
	336	MPP16_UART, /* UART1 RXD */
	337	MPP17_UART, /* UART1 TXD */
	338	MPP18_UART, /* UART1 CTSn */
	339	MPP19_UART, /* UART1 RTSn */
	340	0,
19cfd5c0	341	};
1e780453	342
1e780453 RS	343	static void __init kurobox_pro_init(void)
	344	{
	345	/*
	346	* Setup basic Orion functions. Need to be called early.
	347	*/
9dd0b194	348	orion5x_init();
1e780453	349
19cfd5c0	350	orion5x_mpp_conf(kurobox_pro_mpp_modes);
1e780453	351
044f6c7c LB	352	/*
	353	* Configure peripherals.
	354	*/
	355	orion5x_ehci0_init();
	356	orion5x_ehci1_init();
	357	orion5x_eth_init(&kurobox_pro_eth_data);
	358	orion5x_i2c_init();
	359	orion5x_sata_init(&kurobox_pro_sata_data);
	360	orion5x_uart0_init();
9e956850	361	orion5x_uart1_init();
1d5a1a6e	362	orion5x_xor_init();
044f6c7c LB	363
	364	orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
	365	KUROBOX_PRO_NOR_BOOT_SIZE);
87549251	366	platform_device_register(&kurobox_pro_nor_flash);
044f6c7c LB	367
	368	if (machine_is_kurobox_pro()) {
	369	orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE,
	370	KUROBOX_PRO_NAND_SIZE);
87549251	371	platform_device_register(&kurobox_pro_nand_flash);
044f6c7c LB	372	}
044f6c7c LB	373
1e780453	374	i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
a0087f2f SB	375
	376	/* register Kurobox Pro specific power-off method */
	377	pm_power_off = kurobox_pro_power_off;
1e780453 RS	378	}
1e780453 RS	379
87549251	380	#ifdef CONFIG_MACH_KUROBOX_PRO
1e780453 RS	381	MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro")
1e780453 RS	382	/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
1e780453 RS	383	.boot_params = 0x00000100,
1e780453 RS	384	.init_machine = kurobox_pro_init,
9dd0b194	385	.map_io = orion5x_map_io,
4ee1f6b5	386	.init_early = orion5x_init_early,
9dd0b194 LB	387	.init_irq = orion5x_init_irq,
9dd0b194 LB	388	.timer = &orion5x_timer,
be73a347	389	.fixup = tag_fixup_mem32,
1e780453	390	MACHINE_END
87549251 BB	391	#endif
	392
	393	#ifdef CONFIG_MACH_LINKSTATION_PRO
	394	MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live")
	395	/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
87549251 BB	396	.boot_params = 0x00000100,
	397	.init_machine = kurobox_pro_init,
	398	.map_io = orion5x_map_io,
4ee1f6b5	399	.init_early = orion5x_init_early,
87549251 BB	400	.init_irq = orion5x_init_irq,
	401	.timer = &orion5x_timer,
	402	.fixup = tag_fixup_mem32,
	403	MACHINE_END
	404	#endif