Commit | Line | Data |
---|---|---|
f3a131b9 MM |
1 | /* |
2 | * | |
3 | * QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS Board Setup | |
4 | * | |
5 | * Copyright (C) 2009 Martin Michlmayr <tbm@cyrius.com> | |
6 | * Copyright (C) 2008 Byron Bradley <byron.bbradley@gmail.com> | |
7 | * | |
8 | * This program is free software; you can redistribute it and/or | |
9 | * modify it under the terms of the GNU General Public License | |
10 | * as published by the Free Software Foundation; either version | |
11 | * 2 of the License, or (at your option) any later version. | |
12 | */ | |
13 | ||
14 | #include <linux/kernel.h> | |
15 | #include <linux/init.h> | |
16 | #include <linux/platform_device.h> | |
17 | #include <linux/mtd/physmap.h> | |
18 | #include <linux/spi/flash.h> | |
19 | #include <linux/spi/spi.h> | |
20 | #include <linux/spi/orion_spi.h> | |
21 | #include <linux/i2c.h> | |
22 | #include <linux/mv643xx_eth.h> | |
23 | #include <linux/ata_platform.h> | |
24 | #include <linux/gpio_keys.h> | |
25 | #include <linux/input.h> | |
26 | #include <linux/timex.h> | |
27 | #include <linux/serial_reg.h> | |
28 | #include <linux/pci.h> | |
29 | #include <asm/mach-types.h> | |
30 | #include <asm/mach/arch.h> | |
31 | #include <mach/kirkwood.h> | |
32 | #include "common.h" | |
33 | #include "mpp.h" | |
34 | ||
35 | /**************************************************************************** | |
36 | * 16 MiB NOR flash. The struct mtd_partition is not in the same order as the | |
37 | * partitions on the device because we want to keep compatability with | |
38 | * the QNAP firmware. | |
39 | * Layout as used by QNAP: | |
40 | * 0x00000000-0x00080000 : "U-Boot" | |
41 | * 0x00200000-0x00400000 : "Kernel" | |
42 | * 0x00400000-0x00d00000 : "RootFS" | |
43 | * 0x00d00000-0x01000000 : "RootFS2" | |
44 | * 0x00080000-0x000c0000 : "U-Boot Config" | |
45 | * 0x000c0000-0x00200000 : "NAS Config" | |
46 | * | |
47 | * We'll use "RootFS1" instead of "RootFS" to stay compatible with the layout | |
48 | * used by the QNAP TS-109/TS-209. | |
49 | * | |
50 | ***************************************************************************/ | |
51 | ||
52 | static struct mtd_partition qnap_ts41x_partitions[] = { | |
53 | { | |
54 | .name = "U-Boot", | |
55 | .size = 0x00080000, | |
56 | .offset = 0, | |
57 | .mask_flags = MTD_WRITEABLE, | |
58 | }, { | |
59 | .name = "Kernel", | |
60 | .size = 0x00200000, | |
61 | .offset = 0x00200000, | |
62 | }, { | |
63 | .name = "RootFS1", | |
64 | .size = 0x00900000, | |
65 | .offset = 0x00400000, | |
66 | }, { | |
67 | .name = "RootFS2", | |
68 | .size = 0x00300000, | |
69 | .offset = 0x00d00000, | |
70 | }, { | |
71 | .name = "U-Boot Config", | |
72 | .size = 0x00040000, | |
73 | .offset = 0x00080000, | |
74 | }, { | |
75 | .name = "NAS Config", | |
76 | .size = 0x00140000, | |
77 | .offset = 0x000c0000, | |
78 | }, | |
79 | }; | |
80 | ||
81 | static const struct flash_platform_data qnap_ts41x_flash = { | |
82 | .type = "m25p128", | |
83 | .name = "spi_flash", | |
84 | .parts = qnap_ts41x_partitions, | |
85 | .nr_parts = ARRAY_SIZE(qnap_ts41x_partitions), | |
86 | }; | |
87 | ||
88 | static struct spi_board_info __initdata qnap_ts41x_spi_slave_info[] = { | |
89 | { | |
90 | .modalias = "m25p80", | |
91 | .platform_data = &qnap_ts41x_flash, | |
92 | .irq = -1, | |
93 | .max_speed_hz = 20000000, | |
94 | .bus_num = 0, | |
95 | .chip_select = 0, | |
96 | }, | |
97 | }; | |
98 | ||
99 | static struct i2c_board_info __initdata qnap_ts41x_i2c_rtc = { | |
100 | I2C_BOARD_INFO("s35390a", 0x30), | |
101 | }; | |
102 | ||
103 | static struct mv643xx_eth_platform_data qnap_ts41x_ge00_data = { | |
104 | .phy_addr = MV643XX_ETH_PHY_ADDR(8), | |
105 | }; | |
106 | ||
107 | static struct mv643xx_eth_platform_data qnap_ts41x_ge01_data = { | |
108 | .phy_addr = MV643XX_ETH_PHY_ADDR(0), | |
109 | }; | |
110 | ||
111 | static struct mv_sata_platform_data qnap_ts41x_sata_data = { | |
112 | .n_ports = 2, | |
113 | }; | |
114 | ||
115 | static struct gpio_keys_button qnap_ts41x_buttons[] = { | |
116 | { | |
117 | .code = KEY_COPY, | |
118 | .gpio = 43, | |
119 | .desc = "USB Copy", | |
120 | .active_low = 1, | |
121 | }, | |
122 | { | |
123 | .code = KEY_RESTART, | |
124 | .gpio = 37, | |
125 | .desc = "Reset", | |
126 | .active_low = 1, | |
127 | }, | |
128 | }; | |
129 | ||
130 | static struct gpio_keys_platform_data qnap_ts41x_button_data = { | |
131 | .buttons = qnap_ts41x_buttons, | |
132 | .nbuttons = ARRAY_SIZE(qnap_ts41x_buttons), | |
133 | }; | |
134 | ||
135 | static struct platform_device qnap_ts41x_button_device = { | |
136 | .name = "gpio-keys", | |
137 | .id = -1, | |
138 | .num_resources = 0, | |
139 | .dev = { | |
140 | .platform_data = &qnap_ts41x_button_data, | |
141 | } | |
142 | }; | |
143 | ||
144 | static unsigned int qnap_ts41x_mpp_config[] __initdata = { | |
145 | MPP0_SPI_SCn, | |
146 | MPP1_SPI_MOSI, | |
147 | MPP2_SPI_SCK, | |
148 | MPP3_SPI_MISO, | |
149 | MPP6_SYSRST_OUTn, | |
150 | MPP7_PEX_RST_OUTn, | |
151 | MPP8_TW_SDA, | |
152 | MPP9_TW_SCK, | |
153 | MPP10_UART0_TXD, | |
154 | MPP11_UART0_RXD, | |
155 | MPP13_UART1_TXD, /* PIC controller */ | |
156 | MPP14_UART1_RXD, /* PIC controller */ | |
157 | MPP15_SATA0_ACTn, | |
158 | MPP16_SATA1_ACTn, | |
159 | MPP20_GE1_0, | |
160 | MPP21_GE1_1, | |
161 | MPP22_GE1_2, | |
162 | MPP23_GE1_3, | |
163 | MPP24_GE1_4, | |
164 | MPP25_GE1_5, | |
165 | MPP26_GE1_6, | |
166 | MPP27_GE1_7, | |
167 | MPP30_GE1_10, | |
168 | MPP31_GE1_11, | |
169 | MPP32_GE1_12, | |
170 | MPP33_GE1_13, | |
171 | MPP36_GPIO, /* RAM: 0: 256 MB, 1: 512 MB */ | |
172 | MPP37_GPIO, /* Reset button */ | |
173 | MPP43_GPIO, /* USB Copy button */ | |
174 | MPP44_GPIO, /* Board ID: 0: TS-419U, 1: TS-419 */ | |
175 | MPP45_GPIO, /* JP1: 0: console, 1: LCD */ | |
176 | MPP46_GPIO, /* External SATA HDD1 error indicator */ | |
177 | MPP47_GPIO, /* External SATA HDD2 error indicator */ | |
178 | MPP48_GPIO, /* External SATA HDD3 error indicator */ | |
179 | MPP49_GPIO, /* External SATA HDD4 error indicator */ | |
180 | 0 | |
181 | }; | |
182 | ||
183 | ||
184 | /***************************************************************************** | |
185 | * QNAP TS-x19 specific power off method via UART1-attached PIC | |
186 | ****************************************************************************/ | |
187 | ||
188 | #define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2)) | |
189 | ||
190 | void qnap_ts41x_power_off(void) | |
191 | { | |
192 | /* 19200 baud divisor */ | |
193 | const unsigned divisor = ((kirkwood_tclk + (8 * 19200)) / (16 * 19200)); | |
194 | ||
195 | pr_info("%s: triggering power-off...\n", __func__); | |
196 | ||
197 | /* hijack UART1 and reset into sane state (19200,8n1) */ | |
198 | writel(0x83, UART1_REG(LCR)); | |
199 | writel(divisor & 0xff, UART1_REG(DLL)); | |
200 | writel((divisor >> 8) & 0xff, UART1_REG(DLM)); | |
201 | writel(0x03, UART1_REG(LCR)); | |
202 | writel(0x00, UART1_REG(IER)); | |
203 | writel(0x00, UART1_REG(FCR)); | |
204 | writel(0x00, UART1_REG(MCR)); | |
205 | ||
206 | /* send the power-off command 'A' to PIC */ | |
207 | writel('A', UART1_REG(TX)); | |
208 | } | |
209 | ||
210 | static void __init qnap_ts41x_init(void) | |
211 | { | |
212 | /* | |
213 | * Basic setup. Needs to be called early. | |
214 | */ | |
215 | kirkwood_init(); | |
216 | kirkwood_mpp_conf(qnap_ts41x_mpp_config); | |
217 | ||
218 | kirkwood_uart0_init(); | |
219 | kirkwood_uart1_init(); /* A PIC controller is connected here. */ | |
220 | spi_register_board_info(qnap_ts41x_spi_slave_info, | |
221 | ARRAY_SIZE(qnap_ts41x_spi_slave_info)); | |
222 | kirkwood_spi_init(); | |
223 | kirkwood_i2c_init(); | |
224 | i2c_register_board_info(0, &qnap_ts41x_i2c_rtc, 1); | |
225 | kirkwood_ge00_init(&qnap_ts41x_ge00_data); | |
226 | kirkwood_ge01_init(&qnap_ts41x_ge01_data); | |
227 | kirkwood_sata_init(&qnap_ts41x_sata_data); | |
228 | kirkwood_ehci_init(); | |
229 | platform_device_register(&qnap_ts41x_button_device); | |
230 | ||
231 | pm_power_off = qnap_ts41x_power_off; | |
232 | ||
233 | } | |
234 | ||
235 | static int __init ts41x_pci_init(void) | |
236 | { | |
237 | if (machine_is_ts41x()) | |
238 | kirkwood_pcie_init(); | |
239 | ||
240 | return 0; | |
241 | } | |
242 | subsys_initcall(ts41x_pci_init); | |
243 | ||
244 | MACHINE_START(TS41X, "QNAP TS-41x") | |
245 | /* Maintainer: Martin Michlmayr <tbm@cyrius.com> */ | |
246 | .phys_io = KIRKWOOD_REGS_PHYS_BASE, | |
247 | .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, | |
248 | .boot_params = 0x00000100, | |
249 | .init_machine = qnap_ts41x_init, | |
250 | .map_io = kirkwood_map_io, | |
251 | .init_irq = kirkwood_init_irq, | |
252 | .timer = &kirkwood_timer, | |
253 | MACHINE_END |