projects / linux-2.6-block.git / blame
| Commit | Line | Data |
|---|---|---|
| d234e423 DL |
1 | /* |
| 2 | * Common support for CompuLab CM-T3x CoMs | |
| 3 | */ | |
| 4 | ||
| 5 | / { | |
| 6 | ||
| 7 | memory { | |
| 8 | device_type = "memory"; | |
| 9 | reg = <0x80000000 0x10000000>; /* 256 MB */ | |
| 10 | }; | |
| 11 | ||
| 12 | leds { | |
| 13 | compatible = "gpio-leds"; | |
| dc897926 DL |
14 | pinctrl-names = "default"; |
| 15 | pinctrl-0 = <&green_led_pins>; | |
| d234e423 DL |
16 | ledb { |
| 17 | label = "cm-t3x:green"; | |
| 18 | gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */ | |
| 19 | linux,default-trigger = "heartbeat"; | |
| 20 | }; | |
| 21 | }; | |
| ce5abbb8 DL |
22 | |
| 23 | /* HS USB Port 1 Power */ | |
| 24 | hsusb1_power: hsusb1_power_reg { | |
| 25 | compatible = "regulator-fixed"; | |
| 26 | regulator-name = "hsusb1_vbus"; | |
| 27 | regulator-min-microvolt = <3300000>; | |
| 28 | regulator-max-microvolt = <3300000>; | |
| 29 | startup-delay-us = <70000>; | |
| 30 | }; | |
| 31 | ||
| 32 | /* HS USB Port 2 Power */ | |
| 33 | hsusb2_power: hsusb2_power_reg { | |
| 34 | compatible = "regulator-fixed"; | |
| 35 | regulator-name = "hsusb2_vbus"; | |
| 36 | regulator-min-microvolt = <3300000>; | |
| 37 | regulator-max-microvolt = <3300000>; | |
| 38 | startup-delay-us = <70000>; | |
| 39 | }; | |
| 40 | ||
| 41 | /* HS USB Host PHY on PORT 1 */ | |
| 42 | hsusb1_phy: hsusb1_phy { | |
| 43 | compatible = "usb-nop-xceiv"; | |
| 44 | vcc-supply = <&hsusb1_power>; | |
| 45 | }; | |
| 46 | ||
| 47 | /* HS USB Host PHY on PORT 2 */ | |
| 48 | hsusb2_phy: hsusb2_phy { | |
| 49 | compatible = "usb-nop-xceiv"; | |
| 50 | vcc-supply = <&hsusb2_power>; | |
| 51 | }; | |
| d234e423 DL |
52 | }; |
| 53 | ||
| 54 | &omap3_pmx_core { | |
| 55 | ||
| 56 | uart3_pins: pinmux_uart3_pins { | |
| 57 | pinctrl-single,pins = < | |
| 58 | OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ | |
| 59 | OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ | |
| 60 | >; | |
| 61 | }; | |
| 62 | ||
| 63 | mmc1_pins: pinmux_mmc1_pins { | |
| 64 | pinctrl-single,pins = < | |
| 65 | OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ | |
| 66 | OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ | |
| 67 | OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ | |
| 68 | OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ | |
| 69 | OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ | |
| 70 | OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ | |
| 71 | >; | |
| 72 | }; | |
| dc897926 DL |
73 | |
| 74 | green_led_pins: pinmux_green_led_pins { | |
| 75 | pinctrl-single,pins = < | |
| 76 | OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4) /* sys_clkout2.gpio_186 */ | |
| 77 | >; | |
| 78 | }; | |
| d234e423 DL |
79 | }; |
| 80 | ||
| 81 | &uart3 { | |
| 82 | pinctrl-names = "default"; | |
| 83 | pinctrl-0 = <&uart3_pins>; | |
| 84 | }; | |
| 85 | ||
| 86 | &mmc1 { | |
| 87 | pinctrl-names = "default"; | |
| 88 | pinctrl-0 = <&mmc1_pins>; | |
| 89 | bus-width = <4>; | |
| 90 | }; | |
| 91 | ||
| 4ceb3936 DL |
92 | &mmc3 { |
| 93 | status = "disabled"; | |
| 94 | }; | |
| 95 | ||
| d234e423 DL |
96 | &i2c1 { |
| 97 | clock-frequency = <400000>; | |
| 98 | }; | |
| 99 | ||
| 100 | &i2c3 { | |
| 101 | clock-frequency = <400000>; | |
| 102 | }; | |
| ce5abbb8 DL |
103 | &usbhshost { |
| 104 | port1-mode = "ehci-phy"; | |
| 105 | port2-mode = "ehci-phy"; | |
| 106 | }; | |
| 107 | ||
| 108 | &usbhsehci { | |
| 109 | phys = <&hsusb1_phy &hsusb2_phy>; | |
| 110 | }; |