Commit | Line | Data |
---|---|---|
c769eaf7 SS |
1 | // SPDX-License-Identifier: GPL-2.0 |
2 | /* | |
3 | * Samsung's Exynos4412 based Trats 2 board device tree source | |
4 | * | |
5 | * Copyright (c) 2013 Samsung Electronics Co., Ltd. | |
6 | * http://www.samsung.com | |
7 | * | |
8 | * Device tree source file for Samsung's Trats 2 board which is based on | |
9 | * Samsung's Exynos4412 SoC. | |
10 | */ | |
11 | ||
12 | /dts-v1/; | |
13 | #include "exynos4412.dtsi" | |
14 | #include "exynos4412-ppmu-common.dtsi" | |
15 | #include <dt-bindings/gpio/gpio.h> | |
16 | #include <dt-bindings/interrupt-controller/irq.h> | |
17 | #include <dt-bindings/clock/maxim,max77686.h> | |
18 | #include <dt-bindings/pinctrl/samsung.h> | |
19 | ||
20 | / { | |
21 | compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4"; | |
22 | ||
23 | aliases { | |
24 | i2c11 = &i2c_max77693; | |
25 | i2c12 = &i2c_max77693_fuel; | |
26 | }; | |
27 | ||
28 | chosen { | |
29 | stdout-path = &serial_2; | |
30 | }; | |
31 | ||
32 | firmware@204f000 { | |
33 | compatible = "samsung,secure-firmware"; | |
34 | reg = <0x0204F000 0x1000>; | |
35 | }; | |
36 | ||
37 | fixed-rate-clocks { | |
38 | xxti { | |
39 | compatible = "samsung,clock-xxti", "fixed-clock"; | |
40 | clock-frequency = <0>; | |
41 | }; | |
42 | ||
43 | xusbxti { | |
44 | compatible = "samsung,clock-xusbxti", "fixed-clock"; | |
45 | clock-frequency = <24000000>; | |
46 | }; | |
47 | }; | |
48 | ||
33b9e719 KK |
49 | cam_io_reg: voltage-regulator-1 { |
50 | compatible = "regulator-fixed"; | |
51 | regulator-name = "CAM_SENSOR_A"; | |
52 | regulator-min-microvolt = <2800000>; | |
53 | regulator-max-microvolt = <2800000>; | |
54 | enable-active-high; | |
55 | status = "disabled"; | |
56 | }; | |
c769eaf7 | 57 | |
ca1378d1 | 58 | cam_af_reg: voltage-regulator-2 { |
33b9e719 KK |
59 | compatible = "regulator-fixed"; |
60 | regulator-name = "CAM_AF"; | |
61 | regulator-min-microvolt = <2800000>; | |
62 | regulator-max-microvolt = <2800000>; | |
63 | enable-active-high; | |
64 | status = "disabled"; | |
65 | }; | |
c769eaf7 | 66 | |
ca1378d1 | 67 | vsil12: voltage-regulator-3 { |
33b9e719 KK |
68 | compatible = "regulator-fixed"; |
69 | regulator-name = "VSIL_1.2V"; | |
70 | regulator-min-microvolt = <1200000>; | |
71 | regulator-max-microvolt = <1200000>; | |
72 | gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; | |
73 | enable-active-high; | |
74 | vin-supply = <&buck7_reg>; | |
75 | }; | |
c769eaf7 | 76 | |
ca1378d1 | 77 | vcc33mhl: voltage-regulator-4 { |
33b9e719 KK |
78 | compatible = "regulator-fixed"; |
79 | regulator-name = "VCC_3.3_MHL"; | |
80 | regulator-min-microvolt = <3300000>; | |
81 | regulator-max-microvolt = <3300000>; | |
82 | gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; | |
83 | enable-active-high; | |
84 | }; | |
c769eaf7 | 85 | |
ca1378d1 | 86 | vcc18mhl: voltage-regulator-5 { |
33b9e719 KK |
87 | compatible = "regulator-fixed"; |
88 | regulator-name = "VCC_1.8_MHL"; | |
89 | regulator-min-microvolt = <1800000>; | |
90 | regulator-max-microvolt = <1800000>; | |
91 | gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; | |
92 | enable-active-high; | |
c769eaf7 SS |
93 | }; |
94 | ||
95 | gpio-keys { | |
96 | compatible = "gpio-keys"; | |
492413dd SS |
97 | pinctrl-names = "default"; |
98 | pinctrl-0 = <&gpio_keys>; | |
c769eaf7 SS |
99 | |
100 | key-down { | |
101 | gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; | |
102 | linux,code = <114>; | |
103 | label = "volume down"; | |
104 | debounce-interval = <10>; | |
105 | }; | |
106 | ||
107 | key-up { | |
108 | gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; | |
109 | linux,code = <115>; | |
110 | label = "volume up"; | |
111 | debounce-interval = <10>; | |
112 | }; | |
113 | ||
114 | key-power { | |
115 | gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; | |
116 | linux,code = <116>; | |
117 | label = "power"; | |
118 | debounce-interval = <10>; | |
119 | wakeup-source; | |
120 | }; | |
121 | ||
122 | key-ok { | |
123 | gpios = <&gpx0 1 GPIO_ACTIVE_LOW>; | |
124 | linux,code = <139>; | |
125 | label = "ok"; | |
0076096b | 126 | debounce-interval = <10>; |
c769eaf7 SS |
127 | wakeup-source; |
128 | }; | |
129 | }; | |
130 | ||
131 | i2c_max77693: i2c-gpio-1 { | |
132 | compatible = "i2c-gpio"; | |
133 | gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>; | |
134 | i2c-gpio,delay-us = <2>; | |
135 | #address-cells = <1>; | |
136 | #size-cells = <0>; | |
137 | status = "okay"; | |
138 | ||
139 | max77693@66 { | |
140 | compatible = "maxim,max77693"; | |
141 | interrupt-parent = <&gpx1>; | |
142 | interrupts = <5 IRQ_TYPE_EDGE_FALLING>; | |
43efe4fa SS |
143 | pinctrl-names = "default"; |
144 | pinctrl-0 = <&max77693_irq>; | |
c769eaf7 SS |
145 | reg = <0x66>; |
146 | ||
147 | regulators { | |
148 | esafeout1_reg: ESAFEOUT1 { | |
149 | regulator-name = "ESAFEOUT1"; | |
150 | }; | |
151 | esafeout2_reg: ESAFEOUT2 { | |
152 | regulator-name = "ESAFEOUT2"; | |
153 | }; | |
154 | charger_reg: CHARGER { | |
155 | regulator-name = "CHARGER"; | |
156 | regulator-min-microamp = <60000>; | |
157 | regulator-max-microamp = <2580000>; | |
158 | }; | |
159 | }; | |
160 | ||
161 | max77693_haptic { | |
162 | compatible = "maxim,max77693-haptic"; | |
163 | haptic-supply = <&ldo26_reg>; | |
164 | pwms = <&pwm 0 38022 0>; | |
165 | }; | |
166 | ||
167 | charger { | |
168 | compatible = "maxim,max77693-charger"; | |
169 | ||
170 | maxim,constant-microvolt = <4350000>; | |
171 | maxim,min-system-microvolt = <3600000>; | |
172 | maxim,thermal-regulation-celsius = <100>; | |
173 | maxim,battery-overcurrent-microamp = <3500000>; | |
174 | maxim,charge-input-threshold-microvolt = <4300000>; | |
175 | }; | |
176 | }; | |
177 | }; | |
178 | ||
179 | i2c_max77693_fuel: i2c-gpio-3 { | |
180 | compatible = "i2c-gpio"; | |
181 | gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>, <&gpf1 4 GPIO_ACTIVE_HIGH>; | |
182 | i2c-gpio,delay-us = <2>; | |
183 | #address-cells = <1>; | |
184 | #size-cells = <0>; | |
185 | status = "okay"; | |
186 | ||
187 | max77693-fuel-gauge@36 { | |
188 | compatible = "maxim,max17047"; | |
189 | interrupt-parent = <&gpx2>; | |
190 | interrupts = <3 IRQ_TYPE_EDGE_FALLING>; | |
e2bae133 SS |
191 | pinctrl-names = "default"; |
192 | pinctrl-0 = <&max77693_fuel_irq>; | |
c769eaf7 SS |
193 | reg = <0x36>; |
194 | ||
195 | maxim,over-heat-temp = <700>; | |
196 | maxim,over-volt = <4500>; | |
197 | }; | |
198 | }; | |
199 | ||
200 | i2c-mhl { | |
201 | compatible = "i2c-gpio"; | |
202 | gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>; | |
203 | i2c-gpio,delay-us = <100>; | |
204 | #address-cells = <1>; | |
205 | #size-cells = <0>; | |
206 | ||
207 | pinctrl-0 = <&i2c_mhl_bus>; | |
208 | pinctrl-names = "default"; | |
209 | status = "okay"; | |
210 | ||
211 | sii9234: hdmi-bridge@39 { | |
212 | compatible = "sil,sii9234"; | |
213 | avcc33-supply = <&vcc33mhl>; | |
214 | iovcc18-supply = <&vcc18mhl>; | |
215 | avcc12-supply = <&vsil12>; | |
216 | cvcc12-supply = <&vsil12>; | |
217 | reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>; | |
218 | interrupt-parent = <&gpf3>; | |
219 | interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; | |
220 | reg = <0x39>; | |
221 | ||
222 | port { | |
223 | mhl_to_hdmi: endpoint { | |
224 | remote-endpoint = <&hdmi_to_mhl>; | |
225 | }; | |
226 | }; | |
227 | }; | |
228 | }; | |
229 | ||
230 | wlan_pwrseq: sdhci3-pwrseq { | |
231 | compatible = "mmc-pwrseq-simple"; | |
232 | reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>; | |
233 | clocks = <&max77686 MAX77686_CLK_PMIC>; | |
234 | clock-names = "ext_clock"; | |
235 | }; | |
236 | ||
237 | sound { | |
238 | compatible = "samsung,trats2-audio"; | |
239 | samsung,i2s-controller = <&i2s0>; | |
240 | samsung,model = "Trats2"; | |
241 | samsung,audio-codec = <&wm1811>; | |
242 | samsung,audio-routing = | |
243 | "SPK", "SPKOUTLN", | |
244 | "SPK", "SPKOUTLP", | |
245 | "SPK", "SPKOUTRN", | |
246 | "SPK", "SPKOUTRP"; | |
247 | }; | |
248 | ||
249 | thermistor-ap { | |
250 | compatible = "murata,ncp15wb473"; | |
251 | pullup-uv = <1800000>; /* VCC_1.8V_AP */ | |
252 | pullup-ohm = <100000>; /* 100K */ | |
253 | pulldown-ohm = <100000>; /* 100K */ | |
254 | io-channels = <&adc 1>; /* AP temperature */ | |
255 | }; | |
256 | ||
257 | thermistor-battery { | |
258 | compatible = "murata,ncp15wb473"; | |
259 | pullup-uv = <1800000>; /* VCC_1.8V_AP */ | |
260 | pullup-ohm = <100000>; /* 100K */ | |
261 | pulldown-ohm = <100000>; /* 100K */ | |
262 | io-channels = <&adc 2>; /* Battery temperature */ | |
263 | }; | |
264 | ||
265 | thermal-zones { | |
266 | cpu_thermal: cpu-thermal { | |
267 | cooling-maps { | |
268 | map0 { | |
269 | /* Corresponds to 800MHz at freq_table */ | |
270 | cooling-device = <&cpu0 7 7>; | |
271 | }; | |
272 | map1 { | |
273 | /* Corresponds to 200MHz at freq_table */ | |
274 | cooling-device = <&cpu0 13 13>; | |
275 | }; | |
276 | }; | |
277 | }; | |
278 | }; | |
279 | }; | |
280 | ||
281 | &adc { | |
282 | vdd-supply = <&ldo3_reg>; | |
283 | status = "okay"; | |
284 | }; | |
285 | ||
286 | &bus_dmc { | |
287 | devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; | |
288 | vdd-supply = <&buck1_reg>; | |
289 | status = "okay"; | |
290 | }; | |
291 | ||
292 | &bus_acp { | |
293 | devfreq = <&bus_dmc>; | |
294 | status = "okay"; | |
295 | }; | |
296 | ||
297 | &bus_c2c { | |
298 | devfreq = <&bus_dmc>; | |
299 | status = "okay"; | |
300 | }; | |
301 | ||
302 | &bus_leftbus { | |
303 | devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; | |
304 | vdd-supply = <&buck3_reg>; | |
305 | status = "okay"; | |
306 | }; | |
307 | ||
308 | &bus_rightbus { | |
309 | devfreq = <&bus_leftbus>; | |
310 | status = "okay"; | |
311 | }; | |
312 | ||
313 | &bus_display { | |
314 | devfreq = <&bus_leftbus>; | |
315 | status = "okay"; | |
316 | }; | |
317 | ||
318 | &bus_fsys { | |
319 | devfreq = <&bus_leftbus>; | |
320 | status = "okay"; | |
321 | }; | |
322 | ||
323 | &bus_peri { | |
324 | devfreq = <&bus_leftbus>; | |
325 | status = "okay"; | |
326 | }; | |
327 | ||
328 | &bus_mfc { | |
329 | devfreq = <&bus_leftbus>; | |
330 | status = "okay"; | |
331 | }; | |
332 | ||
333 | &camera { | |
334 | pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>; | |
335 | pinctrl-names = "default"; | |
336 | status = "okay"; | |
337 | assigned-clocks = <&clock CLK_MOUT_CAM0>, | |
338 | <&clock CLK_MOUT_CAM1>; | |
339 | assigned-clock-parents = <&clock CLK_XUSBXTI>, | |
340 | <&clock CLK_XUSBXTI>; | |
341 | }; | |
342 | ||
343 | &cpu0 { | |
344 | cpu0-supply = <&buck2_reg>; | |
345 | }; | |
346 | ||
347 | &csis_0 { | |
348 | status = "okay"; | |
349 | vddcore-supply = <&ldo8_reg>; | |
350 | vddio-supply = <&ldo10_reg>; | |
351 | assigned-clocks = <&clock CLK_MOUT_CSIS0>, | |
352 | <&clock CLK_SCLK_CSIS0>; | |
353 | assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; | |
354 | assigned-clock-rates = <0>, <176000000>; | |
355 | ||
356 | /* Camera C (3) MIPI CSI-2 (CSIS0) */ | |
357 | port@3 { | |
358 | reg = <3>; | |
359 | csis0_ep: endpoint { | |
360 | remote-endpoint = <&s5c73m3_ep>; | |
361 | data-lanes = <1 2 3 4>; | |
362 | samsung,csis-hs-settle = <12>; | |
363 | }; | |
364 | }; | |
365 | }; | |
366 | ||
367 | &csis_1 { | |
368 | status = "okay"; | |
369 | vddcore-supply = <&ldo8_reg>; | |
370 | vddio-supply = <&ldo10_reg>; | |
371 | assigned-clocks = <&clock CLK_MOUT_CSIS1>, | |
372 | <&clock CLK_SCLK_CSIS1>; | |
373 | assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; | |
374 | assigned-clock-rates = <0>, <176000000>; | |
375 | ||
376 | /* Camera D (4) MIPI CSI-2 (CSIS1) */ | |
377 | port@4 { | |
378 | reg = <4>; | |
379 | csis1_ep: endpoint { | |
380 | remote-endpoint = <&is_s5k6a3_ep>; | |
381 | data-lanes = <1>; | |
382 | samsung,csis-hs-settle = <18>; | |
383 | samsung,csis-wclk; | |
384 | }; | |
385 | }; | |
386 | }; | |
387 | ||
388 | &dsi_0 { | |
389 | vddcore-supply = <&ldo8_reg>; | |
390 | vddio-supply = <&ldo10_reg>; | |
391 | samsung,burst-clock-frequency = <500000000>; | |
392 | samsung,esc-clock-frequency = <20000000>; | |
393 | samsung,pll-clock-frequency = <24000000>; | |
394 | }; | |
395 | ||
396 | &exynos_usbphy { | |
397 | vbus-supply = <&esafeout1_reg>; | |
398 | status = "okay"; | |
399 | }; | |
400 | ||
401 | &fimc_0 { | |
402 | status = "okay"; | |
403 | assigned-clocks = <&clock CLK_MOUT_FIMC0>, | |
404 | <&clock CLK_SCLK_FIMC0>; | |
405 | assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; | |
406 | assigned-clock-rates = <0>, <176000000>; | |
407 | }; | |
408 | ||
409 | &fimc_1 { | |
410 | status = "okay"; | |
411 | assigned-clocks = <&clock CLK_MOUT_FIMC1>, | |
412 | <&clock CLK_SCLK_FIMC1>; | |
413 | assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; | |
414 | assigned-clock-rates = <0>, <176000000>; | |
415 | }; | |
416 | ||
417 | &fimc_2 { | |
418 | status = "okay"; | |
419 | assigned-clocks = <&clock CLK_MOUT_FIMC2>, | |
420 | <&clock CLK_SCLK_FIMC2>; | |
421 | assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; | |
422 | assigned-clock-rates = <0>, <176000000>; | |
423 | }; | |
424 | ||
425 | &fimc_3 { | |
426 | status = "okay"; | |
427 | assigned-clocks = <&clock CLK_MOUT_FIMC3>, | |
428 | <&clock CLK_SCLK_FIMC3>; | |
429 | assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; | |
430 | assigned-clock-rates = <0>, <176000000>; | |
431 | }; | |
432 | ||
433 | &fimc_is { | |
434 | pinctrl-0 = <&fimc_is_uart>; | |
435 | pinctrl-names = "default"; | |
436 | status = "okay"; | |
437 | ||
438 | }; | |
439 | ||
440 | &fimc_lite_0 { | |
441 | status = "okay"; | |
442 | }; | |
443 | ||
444 | &fimc_lite_1 { | |
445 | status = "okay"; | |
446 | }; | |
447 | ||
448 | &fimd { | |
449 | status = "okay"; | |
450 | }; | |
451 | ||
452 | &hdmi { | |
453 | hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>; | |
454 | pinctrl-names = "default"; | |
455 | pinctrl-0 = <&hdmi_hpd>; | |
456 | vdd-supply = <&ldo3_reg>; | |
457 | vdd_osc-supply = <&ldo4_reg>; | |
458 | vdd_pll-supply = <&ldo3_reg>; | |
459 | ddc = <&i2c_5>; | |
460 | status = "okay"; | |
461 | ||
462 | ports { | |
463 | #address-cells = <1>; | |
464 | #size-cells = <0>; | |
465 | ||
466 | port@1 { | |
467 | reg = <1>; | |
468 | hdmi_to_mhl: endpoint { | |
469 | remote-endpoint = <&mhl_to_hdmi>; | |
470 | }; | |
471 | }; | |
472 | }; | |
473 | }; | |
474 | ||
475 | &hsotg { | |
476 | vusb_d-supply = <&ldo15_reg>; | |
477 | vusb_a-supply = <&ldo12_reg>; | |
478 | dr_mode = "peripheral"; | |
479 | status = "okay"; | |
480 | }; | |
481 | ||
482 | &i2c_0 { | |
483 | samsung,i2c-sda-delay = <100>; | |
484 | samsung,i2c-slave-addr = <0x10>; | |
485 | samsung,i2c-max-bus-freq = <400000>; | |
486 | pinctrl-0 = <&i2c0_bus>; | |
487 | pinctrl-names = "default"; | |
488 | status = "okay"; | |
489 | ||
490 | s5c73m3: s5c73m3@3c { | |
491 | compatible = "samsung,s5c73m3"; | |
492 | reg = <0x3c>; | |
493 | xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */ | |
494 | vdd-int-supply = <&buck9_reg>; | |
495 | vddio-cis-supply = <&ldo9_reg>; | |
496 | vddio-host-supply = <&ldo18_reg>; | |
497 | vdd-af-supply = <&cam_af_reg>; | |
498 | vdd-reg-supply = <&cam_io_reg>; | |
499 | clock-frequency = <24000000>; | |
500 | /* CAM_A_CLKOUT */ | |
501 | clocks = <&camera 0>; | |
502 | clock-names = "cis_extclk"; | |
503 | status = "disabled"; | |
504 | port { | |
505 | s5c73m3_ep: endpoint { | |
506 | remote-endpoint = <&csis0_ep>; | |
507 | data-lanes = <1 2 3 4>; | |
508 | }; | |
509 | }; | |
510 | }; | |
511 | }; | |
512 | ||
513 | &i2c1_isp { | |
514 | pinctrl-0 = <&fimc_is_i2c1>; | |
515 | pinctrl-names = "default"; | |
516 | ||
517 | s5k6a3@10 { | |
518 | compatible = "samsung,s5k6a3"; | |
519 | reg = <0x10>; | |
520 | svdda-supply = <&cam_io_reg>; | |
521 | svddio-supply = <&ldo19_reg>; | |
522 | afvdd-supply = <&ldo19_reg>; | |
523 | clock-frequency = <24000000>; | |
524 | /* CAM_B_CLKOUT */ | |
525 | clocks = <&camera 1>; | |
526 | clock-names = "extclk"; | |
527 | samsung,camclk-out = <1>; | |
528 | gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>; | |
529 | ||
530 | port { | |
531 | is_s5k6a3_ep: endpoint { | |
532 | remote-endpoint = <&csis1_ep>; | |
533 | data-lanes = <1>; | |
534 | }; | |
535 | }; | |
536 | }; | |
537 | }; | |
538 | ||
539 | &i2c_3 { | |
540 | samsung,i2c-sda-delay = <100>; | |
541 | samsung,i2c-slave-addr = <0x10>; | |
542 | samsung,i2c-max-bus-freq = <400000>; | |
543 | pinctrl-0 = <&i2c3_bus>; | |
544 | pinctrl-names = "default"; | |
545 | status = "okay"; | |
546 | }; | |
547 | ||
548 | &i2c_4 { | |
549 | samsung,i2c-sda-delay = <100>; | |
550 | samsung,i2c-slave-addr = <0x10>; | |
551 | samsung,i2c-max-bus-freq = <100000>; | |
552 | pinctrl-0 = <&i2c4_bus>; | |
553 | pinctrl-names = "default"; | |
554 | status = "okay"; | |
555 | ||
556 | wm1811: wm1811@1a { | |
557 | compatible = "wlf,wm1811"; | |
558 | reg = <0x1a>; | |
559 | clocks = <&pmu_system_controller 0>; | |
560 | clock-names = "MCLK1"; | |
561 | DCVDD-supply = <&ldo3_reg>; | |
562 | DBVDD1-supply = <&ldo3_reg>; | |
563 | wlf,ldo1ena = <&gpj0 4 0>; | |
564 | }; | |
565 | }; | |
566 | ||
567 | &i2c_5 { | |
568 | status = "okay"; | |
569 | }; | |
570 | ||
571 | &i2c_7 { | |
572 | samsung,i2c-sda-delay = <100>; | |
573 | samsung,i2c-slave-addr = <0x10>; | |
574 | samsung,i2c-max-bus-freq = <100000>; | |
575 | pinctrl-0 = <&i2c7_bus>; | |
576 | pinctrl-names = "default"; | |
577 | status = "okay"; | |
578 | ||
579 | max77686: max77686_pmic@9 { | |
580 | compatible = "maxim,max77686"; | |
581 | interrupt-parent = <&gpx0>; | |
582 | interrupts = <7 IRQ_TYPE_NONE>; | |
73d2f794 SS |
583 | pinctrl-0 = <&max77686_irq>; |
584 | pinctrl-names = "default"; | |
c769eaf7 SS |
585 | reg = <0x09>; |
586 | #clock-cells = <1>; | |
587 | ||
588 | voltage-regulators { | |
589 | ldo1_reg: LDO1 { | |
590 | regulator-name = "VALIVE_1.0V_AP"; | |
591 | regulator-min-microvolt = <1000000>; | |
592 | regulator-max-microvolt = <1000000>; | |
593 | regulator-always-on; | |
594 | }; | |
595 | ||
596 | ldo2_reg: LDO2 { | |
597 | regulator-name = "VM1M2_1.2V_AP"; | |
598 | regulator-min-microvolt = <1200000>; | |
599 | regulator-max-microvolt = <1200000>; | |
600 | regulator-always-on; | |
601 | regulator-state-mem { | |
602 | regulator-on-in-suspend; | |
603 | }; | |
604 | }; | |
605 | ||
606 | ldo3_reg: LDO3 { | |
607 | regulator-name = "VCC_1.8V_AP"; | |
608 | regulator-min-microvolt = <1800000>; | |
609 | regulator-max-microvolt = <1800000>; | |
610 | regulator-always-on; | |
611 | }; | |
612 | ||
613 | ldo4_reg: LDO4 { | |
614 | regulator-name = "VCC_2.8V_AP"; | |
615 | regulator-min-microvolt = <2800000>; | |
616 | regulator-max-microvolt = <2800000>; | |
617 | regulator-always-on; | |
618 | }; | |
619 | ||
620 | ldo5_reg: LDO5 { | |
621 | regulator-name = "VCC_1.8V_IO"; | |
622 | regulator-min-microvolt = <1800000>; | |
623 | regulator-max-microvolt = <1800000>; | |
624 | regulator-always-on; | |
625 | }; | |
626 | ||
627 | ldo6_reg: LDO6 { | |
628 | regulator-name = "VMPLL_1.0V_AP"; | |
629 | regulator-min-microvolt = <1000000>; | |
630 | regulator-max-microvolt = <1000000>; | |
631 | regulator-always-on; | |
632 | regulator-state-mem { | |
633 | regulator-on-in-suspend; | |
634 | }; | |
635 | }; | |
636 | ||
637 | ldo7_reg: LDO7 { | |
638 | regulator-name = "VPLL_1.0V_AP"; | |
639 | regulator-min-microvolt = <1000000>; | |
640 | regulator-max-microvolt = <1000000>; | |
641 | regulator-always-on; | |
642 | regulator-state-mem { | |
643 | regulator-on-in-suspend; | |
644 | }; | |
645 | }; | |
646 | ||
647 | ldo8_reg: LDO8 { | |
648 | regulator-name = "VMIPI_1.0V"; | |
649 | regulator-min-microvolt = <1000000>; | |
650 | regulator-max-microvolt = <1000000>; | |
651 | regulator-state-mem { | |
652 | regulator-off-in-suspend; | |
653 | }; | |
654 | }; | |
655 | ||
656 | ldo9_reg: LDO9 { | |
657 | regulator-name = "CAM_ISP_MIPI_1.2V"; | |
658 | regulator-min-microvolt = <1200000>; | |
659 | regulator-max-microvolt = <1200000>; | |
660 | }; | |
661 | ||
662 | ldo10_reg: LDO10 { | |
663 | regulator-name = "VMIPI_1.8V"; | |
664 | regulator-min-microvolt = <1800000>; | |
665 | regulator-max-microvolt = <1800000>; | |
666 | regulator-state-mem { | |
667 | regulator-off-in-suspend; | |
668 | }; | |
669 | }; | |
670 | ||
671 | ldo11_reg: LDO11 { | |
672 | regulator-name = "VABB1_1.95V"; | |
673 | regulator-min-microvolt = <1950000>; | |
674 | regulator-max-microvolt = <1950000>; | |
675 | regulator-always-on; | |
676 | regulator-state-mem { | |
677 | regulator-off-in-suspend; | |
678 | }; | |
679 | }; | |
680 | ||
681 | ldo12_reg: LDO12 { | |
682 | regulator-name = "VUOTG_3.0V"; | |
683 | regulator-min-microvolt = <3000000>; | |
684 | regulator-max-microvolt = <3000000>; | |
685 | regulator-state-mem { | |
686 | regulator-off-in-suspend; | |
687 | }; | |
688 | }; | |
689 | ||
690 | ldo13_reg: LDO13 { | |
691 | regulator-name = "NFC_AVDD_1.8V"; | |
692 | regulator-min-microvolt = <1800000>; | |
693 | regulator-max-microvolt = <1800000>; | |
694 | }; | |
695 | ||
696 | ldo14_reg: LDO14 { | |
697 | regulator-name = "VABB2_1.95V"; | |
698 | regulator-min-microvolt = <1950000>; | |
699 | regulator-max-microvolt = <1950000>; | |
700 | regulator-always-on; | |
701 | regulator-state-mem { | |
702 | regulator-off-in-suspend; | |
703 | }; | |
704 | }; | |
705 | ||
706 | ldo15_reg: LDO15 { | |
707 | regulator-name = "VHSIC_1.0V"; | |
708 | regulator-min-microvolt = <1000000>; | |
709 | regulator-max-microvolt = <1000000>; | |
710 | regulator-state-mem { | |
711 | regulator-on-in-suspend; | |
712 | }; | |
713 | }; | |
714 | ||
715 | ldo16_reg: LDO16 { | |
716 | regulator-name = "VHSIC_1.8V"; | |
717 | regulator-min-microvolt = <1800000>; | |
718 | regulator-max-microvolt = <1800000>; | |
719 | regulator-state-mem { | |
720 | regulator-on-in-suspend; | |
721 | }; | |
722 | }; | |
723 | ||
724 | ldo17_reg: LDO17 { | |
725 | regulator-name = "CAM_SENSOR_CORE_1.2V"; | |
726 | regulator-min-microvolt = <1200000>; | |
727 | regulator-max-microvolt = <1200000>; | |
728 | }; | |
729 | ||
730 | ldo18_reg: LDO18 { | |
731 | regulator-name = "CAM_ISP_SEN_IO_1.8V"; | |
732 | regulator-min-microvolt = <1800000>; | |
733 | regulator-max-microvolt = <1800000>; | |
734 | }; | |
735 | ||
736 | ldo19_reg: LDO19 { | |
737 | regulator-name = "VT_CAM_1.8V"; | |
738 | regulator-min-microvolt = <1800000>; | |
739 | regulator-max-microvolt = <1800000>; | |
740 | }; | |
741 | ||
742 | ldo20_reg: LDO20 { | |
743 | regulator-name = "VDDQ_PRE_1.8V"; | |
744 | regulator-min-microvolt = <1800000>; | |
745 | regulator-max-microvolt = <1800000>; | |
746 | }; | |
747 | ||
748 | ldo21_reg: LDO21 { | |
749 | regulator-name = "VTF_2.8V"; | |
750 | regulator-min-microvolt = <2800000>; | |
751 | regulator-max-microvolt = <2800000>; | |
752 | maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; | |
753 | }; | |
754 | ||
755 | ldo22_reg: LDO22 { | |
756 | regulator-name = "VMEM_VDD_2.8V"; | |
757 | regulator-min-microvolt = <2800000>; | |
758 | regulator-max-microvolt = <2800000>; | |
759 | maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; | |
760 | }; | |
761 | ||
762 | ldo23_reg: LDO23 { | |
763 | regulator-name = "TSP_AVDD_3.3V"; | |
764 | regulator-min-microvolt = <3300000>; | |
765 | regulator-max-microvolt = <3300000>; | |
766 | }; | |
767 | ||
768 | ldo24_reg: LDO24 { | |
769 | regulator-name = "TSP_VDD_1.8V"; | |
770 | regulator-min-microvolt = <1800000>; | |
771 | regulator-max-microvolt = <1800000>; | |
772 | }; | |
773 | ||
774 | ldo25_reg: LDO25 { | |
775 | regulator-name = "LDO25"; | |
776 | }; | |
777 | ||
778 | ldo26_reg: LDO26 { | |
779 | regulator-name = "MOTOR_VCC_3.0V"; | |
780 | regulator-min-microvolt = <3000000>; | |
781 | regulator-max-microvolt = <3000000>; | |
782 | }; | |
783 | ||
784 | buck1_reg: BUCK1 { | |
785 | regulator-name = "vdd_mif"; | |
786 | regulator-min-microvolt = <850000>; | |
787 | regulator-max-microvolt = <1100000>; | |
788 | regulator-always-on; | |
789 | regulator-boot-on; | |
790 | regulator-state-mem { | |
791 | regulator-off-in-suspend; | |
792 | }; | |
793 | }; | |
794 | ||
795 | buck2_reg: BUCK2 { | |
796 | regulator-name = "vdd_arm"; | |
797 | regulator-min-microvolt = <850000>; | |
798 | regulator-max-microvolt = <1500000>; | |
799 | regulator-always-on; | |
800 | regulator-boot-on; | |
801 | regulator-state-mem { | |
802 | regulator-on-in-suspend; | |
803 | }; | |
804 | }; | |
805 | ||
806 | buck3_reg: BUCK3 { | |
807 | regulator-name = "vdd_int"; | |
808 | regulator-min-microvolt = <850000>; | |
809 | regulator-max-microvolt = <1150000>; | |
810 | regulator-always-on; | |
811 | regulator-boot-on; | |
812 | regulator-state-mem { | |
813 | regulator-off-in-suspend; | |
814 | }; | |
815 | }; | |
816 | ||
817 | buck4_reg: BUCK4 { | |
818 | regulator-name = "vdd_g3d"; | |
819 | regulator-min-microvolt = <850000>; | |
820 | regulator-max-microvolt = <1150000>; | |
821 | regulator-boot-on; | |
822 | regulator-state-mem { | |
823 | regulator-off-in-suspend; | |
824 | }; | |
825 | }; | |
826 | ||
827 | buck5_reg: BUCK5 { | |
828 | regulator-name = "VMEM_1.2V_AP"; | |
829 | regulator-min-microvolt = <1200000>; | |
830 | regulator-max-microvolt = <1200000>; | |
831 | regulator-always-on; | |
832 | }; | |
833 | ||
834 | buck6_reg: BUCK6 { | |
835 | regulator-name = "VCC_SUB_1.35V"; | |
836 | regulator-min-microvolt = <1350000>; | |
837 | regulator-max-microvolt = <1350000>; | |
838 | regulator-always-on; | |
839 | }; | |
840 | ||
841 | buck7_reg: BUCK7 { | |
842 | regulator-name = "VCC_SUB_2.0V"; | |
843 | regulator-min-microvolt = <2000000>; | |
844 | regulator-max-microvolt = <2000000>; | |
845 | regulator-always-on; | |
846 | }; | |
847 | ||
848 | buck8_reg: BUCK8 { | |
849 | regulator-name = "VMEM_VDDF_3.0V"; | |
850 | regulator-min-microvolt = <2850000>; | |
851 | regulator-max-microvolt = <2850000>; | |
852 | maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; | |
853 | }; | |
854 | ||
855 | buck9_reg: BUCK9 { | |
856 | regulator-name = "CAM_ISP_CORE_1.2V"; | |
857 | regulator-min-microvolt = <1000000>; | |
858 | regulator-max-microvolt = <1200000>; | |
859 | }; | |
860 | }; | |
861 | }; | |
862 | }; | |
863 | ||
864 | &i2c_8 { | |
865 | status = "okay"; | |
866 | }; | |
867 | ||
868 | &i2s0 { | |
869 | pinctrl-0 = <&i2s0_bus>; | |
870 | pinctrl-names = "default"; | |
871 | status = "okay"; | |
872 | }; | |
873 | ||
874 | &mixer { | |
875 | status = "okay"; | |
876 | }; | |
877 | ||
878 | &mshc_0 { | |
879 | broken-cd; | |
880 | non-removable; | |
881 | card-detect-delay = <200>; | |
882 | vmmc-supply = <&ldo22_reg>; | |
883 | clock-frequency = <400000000>; | |
884 | samsung,dw-mshc-ciu-div = <0>; | |
885 | samsung,dw-mshc-sdr-timing = <2 3>; | |
886 | samsung,dw-mshc-ddr-timing = <1 2>; | |
887 | pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; | |
888 | pinctrl-names = "default"; | |
889 | status = "okay"; | |
890 | bus-width = <8>; | |
891 | cap-mmc-highspeed; | |
892 | }; | |
893 | ||
894 | &pmu_system_controller { | |
895 | assigned-clocks = <&pmu_system_controller 0>; | |
896 | assigned-clock-parents = <&clock CLK_XUSBXTI>; | |
897 | }; | |
898 | ||
899 | &pinctrl_0 { | |
900 | pinctrl-names = "default"; | |
901 | pinctrl-0 = <&sleep0>; | |
902 | ||
903 | mhl_int: mhl-int { | |
904 | samsung,pins = "gpf3-5"; | |
905 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; | |
906 | }; | |
907 | ||
908 | i2c_mhl_bus: i2c-mhl-bus { | |
909 | samsung,pins = "gpf0-4", "gpf0-6"; | |
910 | samsung,pin-function = <EXYNOS_PIN_FUNC_2>; | |
911 | samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; | |
912 | samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; | |
913 | }; | |
914 | ||
915 | sleep0: sleep-states { | |
916 | PIN_SLP(gpa0-0, INPUT, NONE); | |
917 | PIN_SLP(gpa0-1, OUT0, NONE); | |
918 | PIN_SLP(gpa0-2, INPUT, NONE); | |
919 | PIN_SLP(gpa0-3, INPUT, UP); | |
920 | PIN_SLP(gpa0-4, INPUT, NONE); | |
921 | PIN_SLP(gpa0-5, INPUT, DOWN); | |
922 | PIN_SLP(gpa0-6, INPUT, DOWN); | |
923 | PIN_SLP(gpa0-7, INPUT, UP); | |
924 | ||
925 | PIN_SLP(gpa1-0, INPUT, DOWN); | |
926 | PIN_SLP(gpa1-1, INPUT, DOWN); | |
927 | PIN_SLP(gpa1-2, INPUT, DOWN); | |
928 | PIN_SLP(gpa1-3, INPUT, DOWN); | |
929 | PIN_SLP(gpa1-4, INPUT, DOWN); | |
930 | PIN_SLP(gpa1-5, INPUT, DOWN); | |
931 | ||
932 | PIN_SLP(gpb-0, INPUT, NONE); | |
933 | PIN_SLP(gpb-1, INPUT, NONE); | |
934 | PIN_SLP(gpb-2, INPUT, NONE); | |
935 | PIN_SLP(gpb-3, INPUT, NONE); | |
936 | PIN_SLP(gpb-4, INPUT, DOWN); | |
937 | PIN_SLP(gpb-5, INPUT, UP); | |
938 | PIN_SLP(gpb-6, INPUT, DOWN); | |
939 | PIN_SLP(gpb-7, INPUT, DOWN); | |
940 | ||
941 | PIN_SLP(gpc0-0, INPUT, DOWN); | |
942 | PIN_SLP(gpc0-1, INPUT, DOWN); | |
943 | PIN_SLP(gpc0-2, INPUT, DOWN); | |
944 | PIN_SLP(gpc0-3, INPUT, DOWN); | |
945 | PIN_SLP(gpc0-4, INPUT, DOWN); | |
946 | ||
947 | PIN_SLP(gpc1-0, INPUT, NONE); | |
948 | PIN_SLP(gpc1-1, PREV, NONE); | |
949 | PIN_SLP(gpc1-2, INPUT, NONE); | |
950 | PIN_SLP(gpc1-3, INPUT, NONE); | |
951 | PIN_SLP(gpc1-4, INPUT, NONE); | |
952 | ||
953 | PIN_SLP(gpd0-0, INPUT, DOWN); | |
954 | PIN_SLP(gpd0-1, INPUT, DOWN); | |
955 | PIN_SLP(gpd0-2, INPUT, NONE); | |
956 | PIN_SLP(gpd0-3, INPUT, NONE); | |
957 | ||
958 | PIN_SLP(gpd1-0, INPUT, DOWN); | |
959 | PIN_SLP(gpd1-1, INPUT, DOWN); | |
960 | PIN_SLP(gpd1-2, INPUT, NONE); | |
961 | PIN_SLP(gpd1-3, INPUT, NONE); | |
962 | ||
963 | PIN_SLP(gpf0-0, INPUT, NONE); | |
964 | PIN_SLP(gpf0-1, INPUT, NONE); | |
965 | PIN_SLP(gpf0-2, INPUT, DOWN); | |
966 | PIN_SLP(gpf0-3, INPUT, DOWN); | |
967 | PIN_SLP(gpf0-4, INPUT, NONE); | |
968 | PIN_SLP(gpf0-5, INPUT, DOWN); | |
969 | PIN_SLP(gpf0-6, INPUT, NONE); | |
970 | PIN_SLP(gpf0-7, INPUT, DOWN); | |
971 | ||
972 | PIN_SLP(gpf1-0, INPUT, DOWN); | |
973 | PIN_SLP(gpf1-1, INPUT, DOWN); | |
974 | PIN_SLP(gpf1-2, INPUT, DOWN); | |
975 | PIN_SLP(gpf1-3, INPUT, DOWN); | |
976 | PIN_SLP(gpf1-4, INPUT, NONE); | |
977 | PIN_SLP(gpf1-5, INPUT, NONE); | |
978 | PIN_SLP(gpf1-6, INPUT, DOWN); | |
979 | PIN_SLP(gpf1-7, PREV, NONE); | |
980 | ||
981 | PIN_SLP(gpf2-0, PREV, NONE); | |
982 | PIN_SLP(gpf2-1, INPUT, DOWN); | |
983 | PIN_SLP(gpf2-2, INPUT, DOWN); | |
984 | PIN_SLP(gpf2-3, INPUT, DOWN); | |
985 | PIN_SLP(gpf2-4, INPUT, DOWN); | |
986 | PIN_SLP(gpf2-5, INPUT, DOWN); | |
987 | PIN_SLP(gpf2-6, INPUT, NONE); | |
988 | PIN_SLP(gpf2-7, INPUT, NONE); | |
989 | ||
990 | PIN_SLP(gpf3-0, INPUT, NONE); | |
991 | PIN_SLP(gpf3-1, PREV, NONE); | |
992 | PIN_SLP(gpf3-2, PREV, NONE); | |
993 | PIN_SLP(gpf3-3, PREV, NONE); | |
994 | PIN_SLP(gpf3-4, OUT1, NONE); | |
995 | PIN_SLP(gpf3-5, INPUT, DOWN); | |
996 | ||
997 | PIN_SLP(gpj0-0, PREV, NONE); | |
998 | PIN_SLP(gpj0-1, PREV, NONE); | |
999 | PIN_SLP(gpj0-2, PREV, NONE); | |
1000 | PIN_SLP(gpj0-3, INPUT, DOWN); | |
1001 | PIN_SLP(gpj0-4, PREV, NONE); | |
1002 | PIN_SLP(gpj0-5, PREV, NONE); | |
1003 | PIN_SLP(gpj0-6, INPUT, DOWN); | |
1004 | PIN_SLP(gpj0-7, INPUT, DOWN); | |
1005 | ||
1006 | PIN_SLP(gpj1-0, INPUT, DOWN); | |
1007 | PIN_SLP(gpj1-1, PREV, NONE); | |
1008 | PIN_SLP(gpj1-2, PREV, NONE); | |
1009 | PIN_SLP(gpj1-3, INPUT, DOWN); | |
1010 | PIN_SLP(gpj1-4, INPUT, DOWN); | |
1011 | }; | |
1012 | }; | |
1013 | ||
1014 | &pinctrl_1 { | |
1015 | pinctrl-names = "default"; | |
1016 | pinctrl-0 = <&sleep1>; | |
1017 | ||
492413dd SS |
1018 | gpio_keys: gpio-keys { |
1019 | samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3"; | |
1020 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; | |
1021 | }; | |
1022 | ||
73d2f794 SS |
1023 | max77686_irq: max77686-irq { |
1024 | samsung,pins = "gpx0-7"; | |
1025 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; | |
1026 | }; | |
1027 | ||
43efe4fa SS |
1028 | max77693_irq: max77693-irq { |
1029 | samsung,pins = "gpx1-5"; | |
1030 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; | |
1031 | }; | |
1032 | ||
e2bae133 SS |
1033 | max77693_fuel_irq: max77693-fuel-irq { |
1034 | samsung,pins = "gpx2-3"; | |
1035 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; | |
1036 | }; | |
1037 | ||
965228d3 SS |
1038 | sdhci2_cd: sdhci2-cd-irq { |
1039 | samsung,pins = "gpx3-4"; | |
1040 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; | |
1041 | }; | |
1042 | ||
c769eaf7 SS |
1043 | hdmi_hpd: hdmi-hpd { |
1044 | samsung,pins = "gpx3-7"; | |
1045 | samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; | |
1046 | }; | |
1047 | ||
1048 | sleep1: sleep-states { | |
1049 | PIN_SLP(gpk0-0, PREV, NONE); | |
1050 | PIN_SLP(gpk0-1, PREV, NONE); | |
1051 | PIN_SLP(gpk0-2, OUT0, NONE); | |
1052 | PIN_SLP(gpk0-3, PREV, NONE); | |
1053 | PIN_SLP(gpk0-4, PREV, NONE); | |
1054 | PIN_SLP(gpk0-5, PREV, NONE); | |
1055 | PIN_SLP(gpk0-6, PREV, NONE); | |
1056 | ||
1057 | PIN_SLP(gpk1-0, INPUT, DOWN); | |
1058 | PIN_SLP(gpk1-1, INPUT, DOWN); | |
1059 | PIN_SLP(gpk1-2, INPUT, DOWN); | |
1060 | PIN_SLP(gpk1-3, PREV, NONE); | |
1061 | PIN_SLP(gpk1-4, PREV, NONE); | |
1062 | PIN_SLP(gpk1-5, PREV, NONE); | |
1063 | PIN_SLP(gpk1-6, PREV, NONE); | |
1064 | ||
1065 | PIN_SLP(gpk2-0, INPUT, DOWN); | |
1066 | PIN_SLP(gpk2-1, INPUT, DOWN); | |
1067 | PIN_SLP(gpk2-2, INPUT, DOWN); | |
1068 | PIN_SLP(gpk2-3, INPUT, DOWN); | |
1069 | PIN_SLP(gpk2-4, INPUT, DOWN); | |
1070 | PIN_SLP(gpk2-5, INPUT, DOWN); | |
1071 | PIN_SLP(gpk2-6, INPUT, DOWN); | |
1072 | ||
1073 | PIN_SLP(gpk3-0, OUT0, NONE); | |
1074 | PIN_SLP(gpk3-1, INPUT, NONE); | |
1075 | PIN_SLP(gpk3-2, INPUT, DOWN); | |
1076 | PIN_SLP(gpk3-3, INPUT, NONE); | |
1077 | PIN_SLP(gpk3-4, INPUT, NONE); | |
1078 | PIN_SLP(gpk3-5, INPUT, NONE); | |
1079 | PIN_SLP(gpk3-6, INPUT, NONE); | |
1080 | ||
1081 | PIN_SLP(gpl0-0, INPUT, DOWN); | |
1082 | PIN_SLP(gpl0-1, INPUT, DOWN); | |
1083 | PIN_SLP(gpl0-2, INPUT, DOWN); | |
1084 | PIN_SLP(gpl0-3, INPUT, DOWN); | |
1085 | PIN_SLP(gpl0-4, PREV, NONE); | |
1086 | PIN_SLP(gpl0-6, PREV, NONE); | |
1087 | ||
1088 | PIN_SLP(gpl1-0, INPUT, DOWN); | |
1089 | PIN_SLP(gpl1-1, INPUT, DOWN); | |
1090 | PIN_SLP(gpl2-0, INPUT, DOWN); | |
1091 | PIN_SLP(gpl2-1, INPUT, DOWN); | |
1092 | PIN_SLP(gpl2-2, INPUT, DOWN); | |
1093 | PIN_SLP(gpl2-3, INPUT, DOWN); | |
1094 | PIN_SLP(gpl2-4, INPUT, DOWN); | |
1095 | PIN_SLP(gpl2-5, INPUT, DOWN); | |
1096 | PIN_SLP(gpl2-6, PREV, NONE); | |
1097 | PIN_SLP(gpl2-7, INPUT, DOWN); | |
1098 | ||
1099 | PIN_SLP(gpm0-0, INPUT, DOWN); | |
1100 | PIN_SLP(gpm0-1, INPUT, DOWN); | |
1101 | PIN_SLP(gpm0-2, INPUT, DOWN); | |
1102 | PIN_SLP(gpm0-3, INPUT, DOWN); | |
1103 | PIN_SLP(gpm0-4, INPUT, DOWN); | |
1104 | PIN_SLP(gpm0-5, INPUT, DOWN); | |
1105 | PIN_SLP(gpm0-6, INPUT, DOWN); | |
1106 | PIN_SLP(gpm0-7, INPUT, DOWN); | |
1107 | ||
1108 | PIN_SLP(gpm1-0, INPUT, DOWN); | |
1109 | PIN_SLP(gpm1-1, INPUT, DOWN); | |
1110 | PIN_SLP(gpm1-2, INPUT, NONE); | |
1111 | PIN_SLP(gpm1-3, INPUT, NONE); | |
1112 | PIN_SLP(gpm1-4, INPUT, NONE); | |
1113 | PIN_SLP(gpm1-5, INPUT, NONE); | |
1114 | PIN_SLP(gpm1-6, INPUT, DOWN); | |
1115 | ||
1116 | PIN_SLP(gpm2-0, INPUT, NONE); | |
1117 | PIN_SLP(gpm2-1, INPUT, NONE); | |
1118 | PIN_SLP(gpm2-2, INPUT, DOWN); | |
1119 | PIN_SLP(gpm2-3, INPUT, DOWN); | |
1120 | PIN_SLP(gpm2-4, INPUT, DOWN); | |
1121 | ||
1122 | PIN_SLP(gpm3-0, PREV, NONE); | |
1123 | PIN_SLP(gpm3-1, PREV, NONE); | |
1124 | PIN_SLP(gpm3-2, PREV, NONE); | |
1125 | PIN_SLP(gpm3-3, OUT1, NONE); | |
1126 | PIN_SLP(gpm3-4, INPUT, DOWN); | |
1127 | PIN_SLP(gpm3-5, INPUT, DOWN); | |
1128 | PIN_SLP(gpm3-6, INPUT, DOWN); | |
1129 | PIN_SLP(gpm3-7, INPUT, DOWN); | |
1130 | ||
1131 | PIN_SLP(gpm4-0, INPUT, DOWN); | |
1132 | PIN_SLP(gpm4-1, INPUT, DOWN); | |
1133 | PIN_SLP(gpm4-2, INPUT, DOWN); | |
1134 | PIN_SLP(gpm4-3, INPUT, DOWN); | |
1135 | PIN_SLP(gpm4-4, INPUT, DOWN); | |
1136 | PIN_SLP(gpm4-5, INPUT, DOWN); | |
1137 | PIN_SLP(gpm4-6, INPUT, DOWN); | |
1138 | PIN_SLP(gpm4-7, INPUT, DOWN); | |
1139 | ||
1140 | PIN_SLP(gpy0-0, INPUT, DOWN); | |
1141 | PIN_SLP(gpy0-1, INPUT, DOWN); | |
1142 | PIN_SLP(gpy0-2, INPUT, DOWN); | |
1143 | PIN_SLP(gpy0-3, INPUT, DOWN); | |
1144 | PIN_SLP(gpy0-4, INPUT, DOWN); | |
1145 | PIN_SLP(gpy0-5, INPUT, DOWN); | |
1146 | ||
1147 | PIN_SLP(gpy1-0, INPUT, DOWN); | |
1148 | PIN_SLP(gpy1-1, INPUT, DOWN); | |
1149 | PIN_SLP(gpy1-2, INPUT, DOWN); | |
1150 | PIN_SLP(gpy1-3, INPUT, DOWN); | |
1151 | ||
1152 | PIN_SLP(gpy2-0, PREV, NONE); | |
1153 | PIN_SLP(gpy2-1, INPUT, DOWN); | |
1154 | PIN_SLP(gpy2-2, INPUT, NONE); | |
1155 | PIN_SLP(gpy2-3, INPUT, NONE); | |
1156 | PIN_SLP(gpy2-4, INPUT, NONE); | |
1157 | PIN_SLP(gpy2-5, INPUT, NONE); | |
1158 | ||
1159 | PIN_SLP(gpy3-0, INPUT, DOWN); | |
1160 | PIN_SLP(gpy3-1, INPUT, DOWN); | |
1161 | PIN_SLP(gpy3-2, INPUT, DOWN); | |
1162 | PIN_SLP(gpy3-3, INPUT, DOWN); | |
1163 | PIN_SLP(gpy3-4, INPUT, DOWN); | |
1164 | PIN_SLP(gpy3-5, INPUT, DOWN); | |
1165 | PIN_SLP(gpy3-6, INPUT, DOWN); | |
1166 | PIN_SLP(gpy3-7, INPUT, DOWN); | |
1167 | ||
1168 | PIN_SLP(gpy4-0, INPUT, DOWN); | |
1169 | PIN_SLP(gpy4-1, INPUT, DOWN); | |
1170 | PIN_SLP(gpy4-2, INPUT, DOWN); | |
1171 | PIN_SLP(gpy4-3, INPUT, DOWN); | |
1172 | PIN_SLP(gpy4-4, INPUT, DOWN); | |
1173 | PIN_SLP(gpy4-5, INPUT, DOWN); | |
1174 | PIN_SLP(gpy4-6, INPUT, DOWN); | |
1175 | PIN_SLP(gpy4-7, INPUT, DOWN); | |
1176 | ||
1177 | PIN_SLP(gpy5-0, INPUT, DOWN); | |
1178 | PIN_SLP(gpy5-1, INPUT, DOWN); | |
1179 | PIN_SLP(gpy5-2, INPUT, DOWN); | |
1180 | PIN_SLP(gpy5-3, INPUT, DOWN); | |
1181 | PIN_SLP(gpy5-4, INPUT, DOWN); | |
1182 | PIN_SLP(gpy5-5, INPUT, DOWN); | |
1183 | PIN_SLP(gpy5-6, INPUT, DOWN); | |
1184 | PIN_SLP(gpy5-7, INPUT, DOWN); | |
1185 | ||
1186 | PIN_SLP(gpy6-0, INPUT, DOWN); | |
1187 | PIN_SLP(gpy6-1, INPUT, DOWN); | |
1188 | PIN_SLP(gpy6-2, INPUT, DOWN); | |
1189 | PIN_SLP(gpy6-3, INPUT, DOWN); | |
1190 | PIN_SLP(gpy6-4, INPUT, DOWN); | |
1191 | PIN_SLP(gpy6-5, INPUT, DOWN); | |
1192 | PIN_SLP(gpy6-6, INPUT, DOWN); | |
1193 | PIN_SLP(gpy6-7, INPUT, DOWN); | |
1194 | }; | |
1195 | }; | |
1196 | ||
1197 | &pinctrl_2 { | |
1198 | pinctrl-names = "default"; | |
1199 | pinctrl-0 = <&sleep2>; | |
1200 | ||
1201 | sleep2: sleep-states { | |
1202 | PIN_SLP(gpz-0, INPUT, DOWN); | |
1203 | PIN_SLP(gpz-1, INPUT, DOWN); | |
1204 | PIN_SLP(gpz-2, INPUT, DOWN); | |
1205 | PIN_SLP(gpz-3, INPUT, DOWN); | |
1206 | PIN_SLP(gpz-4, INPUT, DOWN); | |
1207 | PIN_SLP(gpz-5, INPUT, DOWN); | |
1208 | PIN_SLP(gpz-6, INPUT, DOWN); | |
1209 | }; | |
1210 | }; | |
1211 | ||
1212 | &pinctrl_3 { | |
1213 | pinctrl-names = "default"; | |
1214 | pinctrl-0 = <&sleep3>; | |
1215 | ||
1216 | sleep3: sleep-states { | |
1217 | PIN_SLP(gpv0-0, INPUT, DOWN); | |
1218 | PIN_SLP(gpv0-1, INPUT, DOWN); | |
1219 | PIN_SLP(gpv0-2, INPUT, DOWN); | |
1220 | PIN_SLP(gpv0-3, INPUT, DOWN); | |
1221 | PIN_SLP(gpv0-4, INPUT, DOWN); | |
1222 | PIN_SLP(gpv0-5, INPUT, DOWN); | |
1223 | PIN_SLP(gpv0-6, INPUT, DOWN); | |
1224 | PIN_SLP(gpv0-7, INPUT, DOWN); | |
1225 | ||
1226 | PIN_SLP(gpv1-0, INPUT, DOWN); | |
1227 | PIN_SLP(gpv1-1, INPUT, DOWN); | |
1228 | PIN_SLP(gpv1-2, INPUT, DOWN); | |
1229 | PIN_SLP(gpv1-3, INPUT, DOWN); | |
1230 | PIN_SLP(gpv1-4, INPUT, DOWN); | |
1231 | PIN_SLP(gpv1-5, INPUT, DOWN); | |
1232 | PIN_SLP(gpv1-6, INPUT, DOWN); | |
1233 | PIN_SLP(gpv1-7, INPUT, DOWN); | |
1234 | ||
1235 | PIN_SLP(gpv2-0, INPUT, DOWN); | |
1236 | PIN_SLP(gpv2-1, INPUT, DOWN); | |
1237 | PIN_SLP(gpv2-2, INPUT, DOWN); | |
1238 | PIN_SLP(gpv2-3, INPUT, DOWN); | |
1239 | PIN_SLP(gpv2-4, INPUT, DOWN); | |
1240 | PIN_SLP(gpv2-5, INPUT, DOWN); | |
1241 | PIN_SLP(gpv2-6, INPUT, DOWN); | |
1242 | PIN_SLP(gpv2-7, INPUT, DOWN); | |
1243 | ||
1244 | PIN_SLP(gpv3-0, INPUT, DOWN); | |
1245 | PIN_SLP(gpv3-1, INPUT, DOWN); | |
1246 | PIN_SLP(gpv3-2, INPUT, DOWN); | |
1247 | PIN_SLP(gpv3-3, INPUT, DOWN); | |
1248 | PIN_SLP(gpv3-4, INPUT, DOWN); | |
1249 | PIN_SLP(gpv3-5, INPUT, DOWN); | |
1250 | PIN_SLP(gpv3-6, INPUT, DOWN); | |
1251 | PIN_SLP(gpv3-7, INPUT, DOWN); | |
1252 | ||
1253 | PIN_SLP(gpv4-0, INPUT, DOWN); | |
1254 | }; | |
1255 | }; | |
1256 | ||
1257 | &pwm { | |
1258 | pinctrl-0 = <&pwm0_out>; | |
1259 | pinctrl-names = "default"; | |
1260 | samsung,pwm-outputs = <0>; | |
1261 | status = "okay"; | |
1262 | }; | |
1263 | ||
1264 | &rtc { | |
1265 | status = "okay"; | |
1266 | clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; | |
1267 | clock-names = "rtc", "rtc_src"; | |
1268 | }; | |
1269 | ||
1270 | &sdhci_2 { | |
1271 | bus-width = <4>; | |
b8032118 | 1272 | cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; |
965228d3 | 1273 | pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; |
c769eaf7 SS |
1274 | pinctrl-names = "default"; |
1275 | vmmc-supply = <&ldo21_reg>; | |
1276 | status = "okay"; | |
1277 | }; | |
1278 | ||
1279 | &sdhci_3 { | |
1280 | #address-cells = <1>; | |
1281 | #size-cells = <0>; | |
1282 | non-removable; | |
1283 | bus-width = <4>; | |
1284 | ||
1285 | mmc-pwrseq = <&wlan_pwrseq>; | |
1286 | pinctrl-names = "default"; | |
1287 | pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; | |
1288 | status = "okay"; | |
1289 | ||
1290 | brcmf: wifi@1 { | |
1291 | reg = <1>; | |
1292 | compatible = "brcm,bcm4329-fmac"; | |
1293 | interrupt-parent = <&gpx2>; | |
1294 | interrupts = <5 IRQ_TYPE_NONE>; | |
1295 | interrupt-names = "host-wake"; | |
1296 | }; | |
1297 | }; | |
1298 | ||
1299 | &serial_0 { | |
1300 | status = "okay"; | |
1301 | }; | |
1302 | ||
1303 | &serial_1 { | |
1304 | status = "okay"; | |
1305 | }; | |
1306 | ||
1307 | &serial_2 { | |
1308 | status = "okay"; | |
1309 | }; | |
1310 | ||
1311 | &serial_3 { | |
1312 | status = "okay"; | |
1313 | }; | |
1314 | ||
1315 | &spi_1 { | |
1316 | pinctrl-names = "default"; | |
1317 | pinctrl-0 = <&spi1_bus>; | |
1318 | cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; | |
1319 | status = "okay"; | |
1320 | ||
1321 | s5c73m3_spi: s5c73m3@0 { | |
1322 | compatible = "samsung,s5c73m3"; | |
1323 | spi-max-frequency = <50000000>; | |
1324 | reg = <0>; | |
1325 | controller-data { | |
1326 | samsung,spi-feedback-delay = <2>; | |
1327 | }; | |
1328 | }; | |
1329 | }; | |
1330 | ||
1331 | &tmu { | |
1332 | vtmu-supply = <&ldo10_reg>; | |
1333 | status = "okay"; | |
1334 | }; |