[linux-2.6-block.git] / arch / arm / boot / dts / at91sam9m10g45ek.dts

/*
 * at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board
 *
 *  Copyright (C) 2011 Atmel,
 *                2011 Nicolas Ferre <nicolas.ferre@atmel.com>
 *
 * Licensed under GPLv2 or later.
 */
/dts-v1/;
#include "at91sam9g45.dtsi"
#include <dt-bindings/pwm/pwm.h>

/ {
	model = "Atmel AT91SAM9M10G45-EK";
	compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";

	chosen {
		bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
		stdout-path = "serial0:115200n8";
	};

	memory {
		reg = <0x70000000 0x4000000>;
	};

	clocks {
		slow_xtal {
		      clock-frequency = <32768>;
		};

		main_xtal {
		      clock-frequency = <12000000>;
		};
	};

	ahb {
		apb {
			dbgu: serial@ffffee00 {
				status = "okay";
			};

			usart1: serial@fff90000 {
				pinctrl-0 =
					<&pinctrl_usart1
					 &pinctrl_usart1_rts
					 &pinctrl_usart1_cts>;
				status = "okay";
			};

			macb0: ethernet@fffbc000 {
				phy-mode = "rmii";
				status = "okay";
			};

			i2c0: i2c@fff84000 {
				status = "okay";
				ov2640: camera@30 {
					compatible = "ovti,ov2640";
					reg = <0x30>;
					pinctrl-names = "default";
					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
					resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
					pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
					clocks = <&pck1>;
					clock-names = "xvclk";
					assigned-clocks = <&pck1>;
					assigned-clock-rates = <25000000>;

					port {
						ov2640_0: endpoint {
							remote-endpoint = <&isi_0>;
							bus-width = <8>;
						};
					};
				};
			};

			i2c1: i2c@fff88000 {
				status = "okay";
			};

			watchdog@fffffd40 {
				status = "okay";
			};

			mmc0: mmc@fff80000 {
				pinctrl-0 = <
					&pinctrl_board_mmc0
					&pinctrl_mmc0_slot0_clk_cmd_dat0
					&pinctrl_mmc0_slot0_dat1_3>;
				status = "okay";
				slot@0 {
					reg = <0>;
					bus-width = <4>;
					cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
				};
			};

			mmc1: mmc@fffd0000 {
				pinctrl-0 = <
					&pinctrl_board_mmc1
					&pinctrl_mmc1_slot0_clk_cmd_dat0
					&pinctrl_mmc1_slot0_dat1_3>;
				status = "okay";
				slot@0 {
					reg = <0>;
					bus-width = <4>;
					cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
					wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
				};
			};

			pinctrl@fffff200 {
				camera_sensor {
					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
						atmel,pins =
							<AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
					};

					pinctrl_sensor_reset: sensor_reset-0 {
						atmel,pins =
							<AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
					};

					pinctrl_sensor_power: sensor_power-0 {
						atmel,pins =
							<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
					};
				};
				mmc0 {
					pinctrl_board_mmc0: mmc0-board {
						atmel,pins =
							<AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;	/* PD10 gpio CD pin pull up and deglitch */
					};
				};

				mmc1 {
					pinctrl_board_mmc1: mmc1-board {
						atmel,pins =
							<AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH	/* PD11 gpio CD pin pull up and deglitch */
							 AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;	/* PD29 gpio WP pin pull up */
					};
				};

				pwm0 {
					pinctrl_pwm_leds: pwm-led {
						atmel,pins =
							<AT91_PIOD 0  AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PD0 periph B */
							 AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;	/* PD31 periph B */
					};
				};
			};

			spi0: spi@fffa4000{
				status = "okay";
				cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
				mtd_dataflash@0 {
					compatible = "atmel,at45", "atmel,dataflash";
					spi-max-frequency = <13000000>;
					reg = <0>;
				};
			};

			usb2: gadget@fff78000 {
				atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>;
				status = "okay";
			};

			ac97: sound@fffac000 {
				status = "okay";
			};

			adc0: adc@fffb0000 {
				pinctrl-names = "default";
				pinctrl-0 = <
					&pinctrl_adc0_ad0
					&pinctrl_adc0_ad1
					&pinctrl_adc0_ad2
					&pinctrl_adc0_ad3
					&pinctrl_adc0_ad4
					&pinctrl_adc0_ad5
					&pinctrl_adc0_ad6
					&pinctrl_adc0_ad7>;
				atmel,adc-ts-wires = <4>;
				status = "okay";
			};

			isi@fffb4000 {
				pinctrl-names = "default";
				pinctrl-0 = <&pinctrl_isi_data_0_7>;
				status = "okay";
				port {
					isi_0: endpoint {
						remote-endpoint = <&ov2640_0>;
						bus-width = <8>;
						vsync-active = <1>;
						hsync-active = <1>;
					};
				};
			};

			pwm0: pwm@fffb8000 {
				status = "okay";

				pinctrl-names = "default";
				pinctrl-0 = <&pinctrl_pwm_leds>;
			};

			rtc@fffffd20 {
				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
				status = "okay";
			};

			gpbr: syscon@fffffd60 {
				status = "okay";
			};

			rtc@fffffdb0 {
				status = "okay";
			};
		};

		fb0: fb@0x00500000 {
			display = <&display0>;
			status = "okay";

			display0: display {
				bits-per-pixel = <32>;
				atmel,lcdcon-backlight;
				atmel,dmacon = <0x1>;
				atmel,lcdcon2 = <0x80008002>;
				atmel,guard-time = <9>;
				atmel,lcd-wiring-mode = "RGB";

				display-timings {
					native-mode = <&timing0>;
					timing0: timing0 {
						clock-frequency = <9000000>;
						hactive = <480>;
						vactive = <272>;
						hback-porch = <1>;
						hfront-porch = <1>;
						vback-porch = <40>;
						vfront-porch = <1>;
						hsync-len = <45>;
						vsync-len = <1>;
					};
				};
			};
		};

		ebi: ebi@10000000 {
			status = "okay";

			nand_controller: nand-controller {
				status = "okay";
				pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
				pinctrl-names = "default";

				nand@3 {
					reg = <0x3 0x0 0x800000>;
					rb-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>;
					cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
					nand-bus-width = <8>;
					nand-ecc-mode = "soft";
					nand-on-flash-bbt;
					label = "atmel_nand";

					partitions {
						compatible = "fixed-partitions";
						#address-cells = <1>;
						#size-cells = <1>;

						boot@0 {
							label = "bootstrap/uboot/kernel";
							reg = <0x0 0x400000>;
						};

						rootfs@400000 {
							label = "rootfs";
							reg = <0x400000 0x3C00000>;
						};

						data@4000000 {
							label = "data";
							reg = <0x4000000 0xC000000>;
						};
					};
				};
			};
		};

		usb0: ohci@00700000 {
			status = "okay";
			num-ports = <2>;
			atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
					   &pioD 3 GPIO_ACTIVE_LOW>;
		};

		usb1: ehci@00800000 {
			status = "okay";
		};
	};

	leds {
		compatible = "gpio-leds";

		d8 {
			label = "d8";
			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
			linux,default-trigger = "heartbeat";
		};
	};

	pwmleds {
		compatible = "pwm-leds";

		d6 {
			label = "d6";
			pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>;
			max-brightness = <255>;
			linux,default-trigger = "nand-disk";
		};

		d7 {
			label = "d7";
			pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
			max-brightness = <255>;
			linux,default-trigger = "mmc0";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";

		left_click {
			label = "left_click";
			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
			linux,code = <272>;
			wakeup-source;
		};

		right_click {
			label = "right_click";
			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
			linux,code = <273>;
			wakeup-source;
		};

		left {
			label = "Joystick Left";
			gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
			linux,code = <105>;
		};

		right {
			label = "Joystick Right";
			gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
			linux,code = <106>;
		};

		up {
			label = "Joystick Up";
			gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
			linux,code = <103>;
		};

		down {
			label = "Joystick Down";
			gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
			linux,code = <108>;
		};

		enter {
			label = "Joystick Press";
			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
			linux,code = <28>;
		};
	};
};
Commit	Line	Data
49fe2ba3 NF	1	/*
	2	* at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board
	3	*
	4	* Copyright (C) 2011 Atmel,
	5	* 2011 Nicolas Ferre <nicolas.ferre@atmel.com>
	6	*
	7	* Licensed under GPLv2 or later.
	8	*/
	9	/dts-v1/;
6db64d29	10	#include "at91sam9g45.dtsi"
66844c74	11	#include <dt-bindings/pwm/pwm.h>
49fe2ba3 NF	12
	13	/ {
	14	model = "Atmel AT91SAM9M10G45-EK";
	15	compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
	16
	17	chosen {
aa070464 AB	18	bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
aa070464 AB	19	stdout-path = "serial0:115200n8";
49fe2ba3 NF	20	};
49fe2ba3 NF	21
dcce6ce8	22	memory {
49fe2ba3 NF	23	reg = <0x70000000 0x4000000>;
	24	};
	25
eb5e76ff	26	clocks {
4c67a131 AB	27	slow_xtal {
	28	clock-frequency = <32768>;
	29	};
	30
	31	main_xtal {
	32	clock-frequency = <12000000>;
	33	};
eb5e76ff JCPV	34	};
eb5e76ff JCPV	35
49fe2ba3 NF	36	ahb {
	37	apb {
	38	dbgu: serial@ffffee00 {
	39	status = "okay";
	40	};
	41
	42	usart1: serial@fff90000 {
c58c0c5a JCPV	43	pinctrl-0 =
	44	<&pinctrl_usart1
	45	&pinctrl_usart1_rts
	46	&pinctrl_usart1_cts>;
49fe2ba3 NF	47	status = "okay";
49fe2ba3 NF	48	};
0d4f99d8 NF	49
	50	macb0: ethernet@fffbc000 {
	51	phy-mode = "rmii";
	52	status = "okay";
	53	};
fbc18715 LD	54
	55	i2c0: i2c@fff84000 {
	56	status = "okay";
917cdc5f JW	57	ov2640: camera@30 {
	58	compatible = "ovti,ov2640";
	59	reg = <0x30>;
	60	pinctrl-names = "default";
	61	pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
	62	resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
	63	pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
	64	clocks = <&pck1>;
	65	clock-names = "xvclk";
	66	assigned-clocks = <&pck1>;
	67	assigned-clock-rates = <25000000>;
	68
	69	port {
	70	ov2640_0: endpoint {
	71	remote-endpoint = <&isi_0>;
	72	bus-width = <8>;
	73	};
	74	};
	75	};
fbc18715 LD	76	};
	77
	78	i2c1: i2c@fff88000 {
	79	status = "okay";
	80	};
4134a455	81
c77bcef4 WY	82	watchdog@fffffd40 {
	83	status = "okay";
	84	};
	85
4134a455	86	mmc0: mmc@fff80000 {
199e2ede JCPV	87	pinctrl-0 = <
	88	&pinctrl_board_mmc0
	89	&pinctrl_mmc0_slot0_clk_cmd_dat0
	90	&pinctrl_mmc0_slot0_dat1_3>;
4134a455 LD	91	status = "okay";
	92	slot@0 {
	93	reg = <0>;
	94	bus-width = <4>;
92f8629b	95	cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
4134a455 LD	96	};
	97	};
	98
	99	mmc1: mmc@fffd0000 {
199e2ede JCPV	100	pinctrl-0 = <
	101	&pinctrl_board_mmc1
	102	&pinctrl_mmc1_slot0_clk_cmd_dat0
	103	&pinctrl_mmc1_slot0_dat1_3>;
4134a455 LD	104	status = "okay";
	105	slot@0 {
	106	reg = <0>;
	107	bus-width = <4>;
92f8629b JCPV	108	cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
92f8629b JCPV	109	wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
4134a455 LD	110	};
4134a455 LD	111	};
199e2ede JCPV	112
199e2ede JCPV	113	pinctrl@fffff200 {
917cdc5f JW	114	camera_sensor {
	115	pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
	116	atmel,pins =
	117	<AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
	118	};
	119
	120	pinctrl_sensor_reset: sensor_reset-0 {
	121	atmel,pins =
	122	<AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
	123	};
	124
	125	pinctrl_sensor_power: sensor_power-0 {
	126	atmel,pins =
	127	<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
	128	};
	129	};
199e2ede JCPV	130	mmc0 {
	131	pinctrl_board_mmc0: mmc0-board {
	132	atmel,pins =
c9d0f317	133	<AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD10 gpio CD pin pull up and deglitch */
199e2ede JCPV	134	};
	135	};
	136
	137	mmc1 {
	138	pinctrl_board_mmc1: mmc1-board {
	139	atmel,pins =
c9d0f317 JCPV	140	<AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* PD11 gpio CD pin pull up and deglitch */
c9d0f317 JCPV	141	AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PD29 gpio WP pin pull up */
199e2ede JCPV	142	};
199e2ede JCPV	143	};
eed97298 BS	144
	145	pwm0 {
	146	pinctrl_pwm_leds: pwm-led {
	147	atmel,pins =
	148	<AT91_PIOD 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PD0 periph B */
	149	AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PD31 periph B */
	150	};
	151	};
199e2ede	152	};
b6811e9a RG	153
	154	spi0: spi@fffa4000{
	155	status = "okay";
	156	cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
	157	mtd_dataflash@0 {
	158	compatible = "atmel,at45", "atmel,dataflash";
	159	spi-max-frequency = <13000000>;
	160	reg = <0>;
	161	};
	162	};
24ce10e1 JCPV	163
	164	usb2: gadget@fff78000 {
	165	atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>;
	166	status = "okay";
	167	};
eed97298	168
2b17939d DR	169	ac97: sound@fffac000 {
	170	status = "okay";
	171	};
	172
e10a57e3 AB	173	adc0: adc@fffb0000 {
	174	pinctrl-names = "default";
	175	pinctrl-0 = <
	176	&pinctrl_adc0_ad0
	177	&pinctrl_adc0_ad1
	178	&pinctrl_adc0_ad2
	179	&pinctrl_adc0_ad3
	180	&pinctrl_adc0_ad4
	181	&pinctrl_adc0_ad5
	182	&pinctrl_adc0_ad6
	183	&pinctrl_adc0_ad7>;
	184	atmel,adc-ts-wires = <4>;
	185	status = "okay";
	186	};
	187
917cdc5f JW	188	isi@fffb4000 {
	189	pinctrl-names = "default";
	190	pinctrl-0 = <&pinctrl_isi_data_0_7>;
	191	status = "okay";
	192	port {
	193	isi_0: endpoint {
	194	remote-endpoint = <&ov2640_0>;
	195	bus-width = <8>;
bc81beb8 JW	196	vsync-active = <1>;
bc81beb8 JW	197	hsync-active = <1>;
917cdc5f JW	198	};
	199	};
	200	};
	201
eed97298 BS	202	pwm0: pwm@fffb8000 {
	203	status = "okay";
	204
	205	pinctrl-names = "default";
	206	pinctrl-0 = <&pinctrl_pwm_leds>;
	207	};
4dd7933a	208
199ec7ab BB	209	rtc@fffffd20 {
	210	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
	211	status = "okay";
	212	};
	213
	214	gpbr: syscon@fffffd60 {
	215	status = "okay";
	216	};
	217
4dd7933a EL	218	rtc@fffffdb0 {
	219	status = "okay";
	220	};
49fe2ba3	221	};
d6a01661	222
f4390a79 JCPV	223	fb0: fb@0x00500000 {
	224	display = <&display0>;
	225	status = "okay";
	226
	227	display0: display {
	228	bits-per-pixel = <32>;
	229	atmel,lcdcon-backlight;
	230	atmel,dmacon = <0x1>;
	231	atmel,lcdcon2 = <0x80008002>;
	232	atmel,guard-time = <9>;
	233	atmel,lcd-wiring-mode = "RGB";
	234
	235	display-timings {
	236	native-mode = <&timing0>;
	237	timing0: timing0 {
	238	clock-frequency = <9000000>;
	239	hactive = <480>;
	240	vactive = <272>;
	241	hback-porch = <1>;
	242	hfront-porch = <1>;
	243	vback-porch = <40>;
	244	vfront-porch = <1>;
	245	hsync-len = <45>;
	246	vsync-len = <1>;
	247	};
	248	};
	249	};
	250	};
	251
1004a297	252	ebi: ebi@10000000 {
d6a01661 JCPV	253	status = "okay";
d6a01661 JCPV	254
1004a297 BB	255	nand_controller: nand-controller {
	256	status = "okay";
	257	pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
	258	pinctrl-names = "default";
d6a01661	259
1004a297 BB	260	nand@3 {
	261	reg = <0x3 0x0 0x800000>;
	262	rb-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>;
	263	cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
	264	nand-bus-width = <8>;
	265	nand-ecc-mode = "soft";
	266	nand-on-flash-bbt;
	267	label = "atmel_nand";
	268
	269	partitions {
	270	compatible = "fixed-partitions";
	271	#address-cells = <1>;
	272	#size-cells = <1>;
	273
	274	boot@0 {
	275	label = "bootstrap/uboot/kernel";
	276	reg = <0x0 0x400000>;
	277	};
d6a01661	278
1004a297 BB	279	rootfs@400000 {
	280	label = "rootfs";
	281	reg = <0x400000 0x3C00000>;
	282	};
	283
	284	data@4000000 {
	285	label = "data";
	286	reg = <0x4000000 0xC000000>;
	287	};
	288	};
	289	};
d6a01661	290	};
6a062459	291	};
d6a01661	292
6a062459 JCPV	293	usb0: ohci@00700000 {
	294	status = "okay";
	295	num-ports = <2>;
92f8629b JCPV	296	atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
92f8629b JCPV	297	&pioD 3 GPIO_ACTIVE_LOW>;
d6a01661	298	};
62c5553a JCPV	299
	300	usb1: ehci@00800000 {
	301	status = "okay";
	302	};
49fe2ba3	303	};
f2ee7acd JCPV	304
	305	leds {
	306	compatible = "gpio-leds";
	307
	308	d8 {
	309	label = "d8";
92f8629b	310	gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
f2ee7acd JCPV	311	linux,default-trigger = "heartbeat";
f2ee7acd JCPV	312	};
eed97298 BS	313	};
	314
	315	pwmleds {
	316	compatible = "pwm-leds";
f2ee7acd JCPV	317
	318	d6 {
	319	label = "d6";
66844c74	320	pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>;
eed97298	321	max-brightness = <255>;
f2ee7acd JCPV	322	linux,default-trigger = "nand-disk";
	323	};
	324
	325	d7 {
	326	label = "d7";
66844c74	327	pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
eed97298	328	max-brightness = <255>;
f2ee7acd JCPV	329	linux,default-trigger = "mmc0";
	330	};
	331	};
8a087b0c JCPV	332
	333	gpio_keys {
	334	compatible = "gpio-keys";
8a087b0c JCPV	335
	336	left_click {
	337	label = "left_click";
92f8629b	338	gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
8a087b0c	339	linux,code = <272>;
67ae8b9b	340	wakeup-source;
8a087b0c JCPV	341	};
	342
	343	right_click {
	344	label = "right_click";
92f8629b	345	gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
8a087b0c	346	linux,code = <273>;
67ae8b9b	347	wakeup-source;
8a087b0c JCPV	348	};
	349
	350	left {
	351	label = "Joystick Left";
92f8629b	352	gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
8a087b0c JCPV	353	linux,code = <105>;
	354	};
	355
	356	right {
	357	label = "Joystick Right";
92f8629b	358	gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
8a087b0c JCPV	359	linux,code = <106>;
	360	};
	361
	362	up {
	363	label = "Joystick Up";
92f8629b	364	gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
8a087b0c JCPV	365	linux,code = <103>;
	366	};
	367
	368	down {
	369	label = "Joystick Down";
92f8629b	370	gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
8a087b0c JCPV	371	linux,code = <108>;
	372	};
	373
	374	enter {
	375	label = "Joystick Press";
92f8629b	376	gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
8a087b0c JCPV	377	linux,code = <28>;
	378	};
	379	};
49fe2ba3	380	};