Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | |
2 | Note: "modinfo <module>" prints various informations about a kernel | |
3 | module, among them a complete and up-to-date list of insmod options. | |
4 | This list tends to be outdated because it is updated manually ... | |
5 | ||
6 | ========================================================================== | |
7 | ||
8 | bttv.o | |
9 | the bt848/878 (grabber chip) driver | |
10 | ||
11 | insmod args: | |
12 | card=n card type, see CARDLIST for a list. | |
13 | tuner=n tuner type, see CARDLIST for a list. | |
14 | radio=0/1 card supports radio | |
15 | pll=0/1/2 pll settings | |
16 | 0: don't use PLL | |
17 | 1: 28 MHz crystal installed | |
18 | 2: 35 MHz crystal installed | |
19 | ||
20 | triton1=0/1 for Triton1 (+others) compatibility | |
21 | vsfx=0/1 yet another chipset bug compatibility bit | |
22 | see README.quirks for details on these two. | |
23 | ||
24 | bigendian=n Set the endianness of the gfx framebuffer. | |
25 | Default is native endian. | |
26 | fieldnr=0/1 Count fields. Some TV descrambling software | |
27 | needs this, for others it only generates | |
28 | 50 useless IRQs/sec. default is 0 (off). | |
29 | autoload=0/1 autoload helper modules (tuner, audio). | |
30 | default is 1 (on). | |
31 | bttv_verbose=0/1/2 verbose level (at insmod time, while | |
32 | looking at the hardware). default is 1. | |
33 | bttv_debug=0/1 debug messages (for capture). | |
34 | default is 0 (off). | |
35 | irq_debug=0/1 irq handler debug messages. | |
36 | default is 0 (off). | |
37 | gbuffers=2-32 number of capture buffers for mmap'ed capture. | |
38 | default is 4. | |
39 | gbufsize= size of capture buffers. default and | |
40 | maximum value is 0x208000 (~2MB) | |
41 | no_overlay=0 Enable overlay on broken hardware. There | |
42 | are some chipsets (SIS for example) which | |
43 | are known to have problems with the PCI DMA | |
44 | push used by bttv. bttv will disable overlay | |
45 | by default on this hardware to avoid crashes. | |
46 | With this insmod option you can override this. | |
47 | automute=0/1 Automatically mutes the sound if there is | |
48 | no TV signal, on by default. You might try | |
49 | to disable this if you have bad input signal | |
50 | quality which leading to unwanted sound | |
51 | dropouts. | |
52 | chroma_agc=0/1 AGC of chroma signal, off by default. | |
53 | adc_crush=0/1 Luminance ADC crush, on by default. | |
54 | ||
55 | bttv_gpio=0/1 | |
56 | gpiomask= | |
57 | audioall= | |
58 | audiomux= | |
59 | See Sound-FAQ for a detailed description. | |
60 | ||
61 | remap, card, radio and pll accept up to four comma-separated arguments | |
62 | (for multiple boards). | |
63 | ||
64 | tuner.o | |
65 | The tuner driver. You need this unless you want to use only | |
66 | with a camera or external tuner ... | |
67 | ||
68 | insmod args: | |
69 | debug=1 print some debug info to the syslog | |
70 | type=n type of the tuner chip. n as follows: | |
71 | see CARDLIST for a complete list. | |
72 | pal=[bdgil] select PAL variant (used for some tuners | |
73 | only, important for the audio carrier). | |
74 | ||
75 | tvmixer.o | |
76 | registers a mixer device for the TV card's volume/bass/treble | |
77 | controls (requires a i2c audio control chip like the msp3400). | |
78 | ||
79 | insmod args: | |
80 | debug=1 print some debug info to the syslog. | |
81 | devnr=n allocate device #n (0 == /dev/mixer, | |
82 | 1 = /dev/mixer1, ...), default is to | |
83 | use the first free one. | |
84 | ||
85 | tvaudio.o | |
86 | new, experimental module which is supported to provide a single | |
87 | driver for all simple i2c audio control chips (tda/tea*). | |
88 | ||
89 | insmod args: | |
90 | tda8425 = 1 enable/disable the support for the | |
91 | tda9840 = 1 various chips. | |
92 | tda9850 = 1 The tea6300 can't be autodetected and is | |
93 | tda9855 = 1 therefore off by default, if you have | |
94 | tda9873 = 1 this one on your card (STB uses these) | |
95 | tda9874a = 1 you have to enable it explicitly. | |
96 | tea6300 = 0 The two tda985x chips use the same i2c | |
97 | tea6420 = 1 address and can't be disturgished from | |
98 | pic16c54 = 1 each other, you might have to disable | |
99 | the wrong one. | |
100 | debug = 1 print debug messages | |
101 | ||
102 | insmod args for tda9874a: | |
103 | tda9874a_SIF=1/2 select sound IF input pin (1 or 2) | |
104 | (default is pin 1) | |
105 | tda9874a_AMSEL=0/1 auto-mute select for NICAM (default=0) | |
106 | Please read note 3 below! | |
107 | tda9874a_STD=n select TV sound standard (0..8): | |
108 | 0 - A2, B/G | |
109 | 1 - A2, M (Korea) | |
110 | 2 - A2, D/K (1) | |
111 | 3 - A2, D/K (2) | |
112 | 4 - A2, D/K (3) | |
113 | 5 - NICAM, I | |
114 | 6 - NICAM, B/G | |
115 | 7 - NICAM, D/K (default) | |
116 | 8 - NICAM, L | |
117 | ||
118 | Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips. | |
119 | Note 2: tda9874h/a and tda9875 (which is supported separately by | |
120 | tda9875.o) use the same i2c address so both modules should not be | |
121 | used at the same time. | |
122 | Note 3: Using tda9874a_AMSEL option depends on your TV card design! | |
123 | AMSEL=0: auto-mute will switch between NICAM sound | |
124 | and the sound on 1st carrier (i.e. FM mono or AM). | |
125 | AMSEL=1: auto-mute will switch between NICAM sound | |
126 | and the analog mono input (MONOIN pin). | |
127 | If tda9874a decoder on your card has MONOIN pin not connected, then | |
128 | use only tda9874_AMSEL=0 or don't specify this option at all. | |
129 | For example: | |
130 | card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0 | |
131 | card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only | |
132 | ||
133 | msp3400.o | |
134 | The driver for the msp34xx sound processor chips. If you have a | |
135 | stereo card, you probably want to insmod this one. | |
136 | ||
137 | insmod args: | |
138 | debug=1/2 print some debug info to the syslog, | |
139 | 2 is more verbose. | |
140 | simple=1 Use the "short programming" method. Newer | |
141 | msp34xx versions support this. You need this | |
142 | for dbx stereo. Default is on if supported by | |
143 | the chip. | |
144 | once=1 Don't check the TV-stations Audio mode | |
145 | every few seconds, but only once after | |
146 | channel switches. | |
147 | amsound=1 Audio carrier is AM/NICAM at 6.5 Mhz. This | |
148 | should improve things for french people, the | |
149 | carrier autoscan seems to work with FM only... | |
150 | ||
151 | tea6300.o - OBSOLETE (use tvaudio instead) | |
152 | The driver for the tea6300 fader chip. If you have a stereo | |
153 | card and the msp3400.o doesn't work, you might want to try this | |
154 | one. This chip is seen on most STB TV/FM cards (usually from | |
155 | Gateway OEM sold surplus on auction sites). | |
156 | ||
157 | insmod args: | |
158 | debug=1 print some debug info to the syslog. | |
159 | ||
160 | tda8425.o - OBSOLETE (use tvaudio instead) | |
161 | The driver for the tda8425 fader chip. This driver used to be | |
162 | part of bttv.c, so if your sound used to work but does not | |
163 | anymore, try loading this module. | |
164 | ||
165 | insmod args: | |
166 | debug=1 print some debug info to the syslog. | |
167 | ||
168 | tda985x.o - OBSOLETE (use tvaudio instead) | |
169 | The driver for the tda9850/55 audio chips. | |
170 | ||
171 | insmod args: | |
172 | debug=1 print some debug info to the syslog. | |
173 | chip=9850/9855 set the chip type. |