Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | Documentation for CMI 8330 (SoundPRO) |
2 | ------------------------------------- | |
3 | Alessandro Zummo <azummo@ita.flashnet.it> | |
4 | ||
5 | ( Be sure to read Documentation/sound/oss/SoundPro too ) | |
6 | ||
7 | ||
8 | This adapter is now directly supported by the sb driver. | |
9 | ||
10 | The only thing you have to do is to compile the kernel sound | |
11 | support as a module and to enable kernel ISAPnP support, | |
12 | as shown below. | |
13 | ||
14 | ||
15 | CONFIG_SOUND=m | |
16 | CONFIG_SOUND_SB=m | |
17 | ||
18 | CONFIG_PNP=y | |
19 | CONFIG_ISAPNP=y | |
20 | ||
21 | ||
22 | and optionally: | |
23 | ||
24 | ||
25 | CONFIG_SOUND_MPU401=m | |
26 | ||
27 | for MPU401 support. | |
28 | ||
29 | ||
30 | (I suggest you to use "make menuconfig" or "make xconfig" | |
31 | for a more comfortable configuration editing) | |
32 | ||
33 | ||
34 | ||
35 | Then you can do | |
36 | ||
37 | modprobe sb | |
38 | ||
39 | and everything will be (hopefully) configured. | |
40 | ||
41 | You should get something similar in syslog: | |
42 | ||
43 | sb: CMI8330 detected. | |
44 | sb: CMI8330 sb base located at 0x220 | |
45 | sb: CMI8330 mpu base located at 0x330 | |
46 | sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it> | |
47 | sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5 | |
48 | ||
49 | ||
50 | ||
51 | ||
52 | The old documentation file follows for reference | |
53 | purposes. | |
54 | ||
55 | ||
56 | How to enable CMI 8330 (SOUNDPRO) soundchip on Linux | |
57 | ------------------------------------------ | |
58 | Stefan Laudat <Stefan.Laudat@asit.ro> | |
59 | ||
60 | [Note: The CMI 8338 is unrelated and is supported by cmpci.o] | |
61 | ||
62 | ||
63 | In order to use CMI8330 under Linux you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience. I use isapnp 1.17, but | |
64 | you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/. | |
65 | ||
66 | Of course you will have to compile kernel sound support as module, as shown below: | |
67 | ||
68 | CONFIG_SOUND=m | |
69 | CONFIG_SOUND_OSS=m | |
70 | CONFIG_SOUND_SB=m | |
71 | CONFIG_SOUND_ADLIB=m | |
72 | CONFIG_SOUND_MPU401=m | |
73 | # Mikro$chaft sound system (kinda useful here ;)) | |
74 | CONFIG_SOUND_MSS=m | |
75 | ||
76 | The /etc/isapnp.conf file will be: | |
77 | ||
78 | <snip below> | |
79 | ||
80 | ||
81 | (READPORT 0x0203) | |
82 | (ISOLATE PRESERVE) | |
83 | (IDENTIFY *) | |
84 | (VERBOSITY 2) | |
85 | (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING | |
86 | (VERIFYLD N) | |
87 | ||
88 | ||
89 | # WSS | |
90 | ||
91 | (CONFIGURE CMI0001/16777472 (LD 0 | |
92 | (IO 0 (SIZE 8) (BASE 0x0530)) | |
93 | (IO 1 (SIZE 8) (BASE 0x0388)) | |
94 | (INT 0 (IRQ 7 (MODE +E))) | |
95 | (DMA 0 (CHANNEL 0)) | |
96 | (NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}") | |
97 | (ACT Y) | |
98 | )) | |
99 | ||
100 | # MPU | |
101 | ||
102 | (CONFIGURE CMI0001/16777472 (LD 1 | |
103 | (IO 0 (SIZE 2) (BASE 0x0330)) | |
104 | (INT 0 (IRQ 11 (MODE +E))) | |
105 | (NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}") | |
106 | (ACT Y) | |
107 | )) | |
108 | ||
109 | # Joystick | |
110 | ||
111 | (CONFIGURE CMI0001/16777472 (LD 2 | |
112 | (IO 0 (SIZE 8) (BASE 0x0200)) | |
113 | (NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}") | |
114 | (ACT Y) | |
115 | )) | |
116 | ||
117 | # SoundBlaster | |
118 | ||
119 | (CONFIGURE CMI0001/16777472 (LD 3 | |
120 | (IO 0 (SIZE 16) (BASE 0x0220)) | |
121 | (INT 0 (IRQ 5 (MODE +E))) | |
122 | (DMA 0 (CHANNEL 1)) | |
123 | (DMA 1 (CHANNEL 5)) | |
124 | (NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}") | |
125 | (ACT Y) | |
126 | )) | |
127 | ||
128 | ||
129 | (WAITFORKEY) | |
130 | ||
131 | <end of snip> | |
132 | ||
133 | The module sequence is trivial: | |
134 | ||
135 | /sbin/insmod soundcore | |
136 | /sbin/insmod sound | |
137 | /sbin/insmod uart401 | |
138 | # insert this first | |
139 | /sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1 | |
140 | # The sb module is an alternative to the ad1848 (Microsoft Sound System) | |
141 | # Anyhow, this is full duplex and has MIDI | |
142 | /sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330 | |
143 | ||
144 | ||
145 | ||
146 | Alma Chao <elysian@ethereal.torsion.org> suggests the following /etc/modprobe.conf: | |
147 | ||
148 | alias sound ad1848 | |
149 | alias synth0 opl3 | |
150 | options ad1848 io=0x530 irq=7 dma=0 soundpro=1 | |
151 | options opl3 io=0x388 | |
152 | ||
153 |