[linux-2.6-block.git] / Documentation / filesystems / nfs-rdma.txt

################################################################################
#									       #
#				NFS/RDMA README				       #
#									       #
################################################################################

 Author: NetApp and Open Grid Computing
 Date: February 25, 2008

Table of Contents
~~~~~~~~~~~~~~~~~
 - Overview
 - Getting Help
 - Installation
 - Check RDMA and NFS Setup
 - NFS/RDMA Setup

Overview
~~~~~~~~

  This document describes how to install and setup the Linux NFS/RDMA client
  and server software.

  The NFS/RDMA client was first included in Linux 2.6.24. The NFS/RDMA server
  was first included in the following release, Linux 2.6.25.

  In our testing, we have obtained excellent performance results (full 10Gbit
  wire bandwidth at minimal client CPU) under many workloads. The code passes
  the full Connectathon test suite and operates over both Infiniband and iWARP
  RDMA adapters.

Getting Help
~~~~~~~~~~~~

  If you get stuck, you can ask questions on the

                nfs-rdma-devel@lists.sourceforge.net

  mailing list.

Installation
~~~~~~~~~~~~

  These instructions are a step by step guide to building a machine for
  use with NFS/RDMA.

  - Install an RDMA device

    Any device supported by the drivers in drivers/infiniband/hw is acceptable.

    Testing has been performed using several Mellanox-based IB cards, the
    Ammasso AMS1100 iWARP adapter, and the Chelsio cxgb3 iWARP adapter.

  - Install a Linux distribution and tools

    The first kernel release to contain both the NFS/RDMA client and server was
    Linux 2.6.25  Therefore, a distribution compatible with this and subsequent
    Linux kernel release should be installed.

    The procedures described in this document have been tested with
    distributions from Red Hat's Fedora Project (http://fedora.redhat.com/).

  - Install nfs-utils-1.1.1 or greater on the client

    An NFS/RDMA mount point can only be obtained by using the mount.nfs
    command in nfs-utils-1.1.1 or greater. To see which version of mount.nfs
    you are using, type:

    > /sbin/mount.nfs -V

    If the version is less than 1.1.1 or the command does not exist,
    then you will need to install the latest version of nfs-utils.

    Download the latest package from:

    http://www.kernel.org/pub/linux/utils/nfs

    Uncompress the package and follow the installation instructions.

    If you will not be using GSS and NFSv4, the installation process
    can be simplified by disabling these features when running configure:

    > ./configure --disable-gss --disable-nfsv4

    For more information on this see the package's README and INSTALL files.

    After building the nfs-utils package, there will be a mount.nfs binary in
    the utils/mount directory. This binary can be used to initiate NFS v2, v3,
    or v4 mounts. To initiate a v4 mount, the binary must be called mount.nfs4.
    The standard technique is to create a symlink called mount.nfs4 to mount.nfs.

    NOTE: mount.nfs and therefore nfs-utils-1.1.1 or greater is only needed
    on the NFS client machine. You do not need this specific version of
    nfs-utils on the server. Furthermore, only the mount.nfs command from
    nfs-utils-1.1.1 is needed on the client.

  - Install a Linux kernel with NFS/RDMA

    The NFS/RDMA client and server are both included in the mainline Linux
    kernel version 2.6.25 and later. This and other versions of the 2.6 Linux
    kernel can be found at:

    ftp://ftp.kernel.org/pub/linux/kernel/v2.6/

    Download the sources and place them in an appropriate location.

  - Configure the RDMA stack

    Make sure your kernel configuration has RDMA support enabled. Under
    Device Drivers -> InfiniBand support, update the kernel configuration
    to enable InfiniBand support [NOTE: the option name is misleading. Enabling
    InfiniBand support is required for all RDMA devices (IB, iWARP, etc.)].

    Enable the appropriate IB HCA support (mlx4, mthca, ehca, ipath, etc.) or
    iWARP adapter support (amso, cxgb3, etc.).

    If you are using InfiniBand, be sure to enable IP-over-InfiniBand support.

  - Configure the NFS client and server

    Your kernel configuration must also have NFS file system support and/or
    NFS server support enabled. These and other NFS related configuration
    options can be found under File Systems -> Network File Systems.

  - Build, install, reboot

    The NFS/RDMA code will be enabled automatically if NFS and RDMA
    are turned on. The NFS/RDMA client and server are configured via the hidden
    SUNRPC_XPRT_RDMA config option that depends on SUNRPC and INFINIBAND. The
    value of SUNRPC_XPRT_RDMA will be:

     - N if either SUNRPC or INFINIBAND are N, in this case the NFS/RDMA client
       and server will not be built
     - M if both SUNRPC and INFINIBAND are on (M or Y) and at least one is M,
       in this case the NFS/RDMA client and server will be built as modules
     - Y if both SUNRPC and INFINIBAND are Y, in this case the NFS/RDMA client
       and server will be built into the kernel

    Therefore, if you have followed the steps above and turned no NFS and RDMA,
    the NFS/RDMA client and server will be built.

    Build a new kernel, install it, boot it.

Check RDMA and NFS Setup
~~~~~~~~~~~~~~~~~~~~~~~~

    Before configuring the NFS/RDMA software, it is a good idea to test
    your new kernel to ensure that the kernel is working correctly.
    In particular, it is a good idea to verify that the RDMA stack
    is functioning as expected and standard NFS over TCP/IP and/or UDP/IP
    is working properly.

  - Check RDMA Setup

    If you built the RDMA components as modules, load them at
    this time. For example, if you are using a Mellanox Tavor/Sinai/Arbel
    card:

    > modprobe ib_mthca
    > modprobe ib_ipoib

    If you are using InfiniBand, make sure there is a Subnet Manager (SM)
    running on the network. If your IB switch has an embedded SM, you can
    use it. Otherwise, you will need to run an SM, such as OpenSM, on one
    of your end nodes.

    If an SM is running on your network, you should see the following:

    > cat /sys/class/infiniband/driverX/ports/1/state
    4: ACTIVE

    where driverX is mthca0, ipath5, ehca3, etc.

    To further test the InfiniBand software stack, use IPoIB (this
    assumes you have two IB hosts named host1 and host2):

    host1> ifconfig ib0 a.b.c.x
    host2> ifconfig ib0 a.b.c.y
    host1> ping a.b.c.y
    host2> ping a.b.c.x

    For other device types, follow the appropriate procedures.

  - Check NFS Setup

    For the NFS components enabled above (client and/or server),
    test their functionality over standard Ethernet using TCP/IP or UDP/IP.

NFS/RDMA Setup
~~~~~~~~~~~~~~

  We recommend that you use two machines, one to act as the client and
  one to act as the server.

  One time configuration:

  - On the server system, configure the /etc/exports file and
    start the NFS/RDMA server.

    Exports entries with the following format have been tested:

    /vol0   10.97.103.47(rw,async) 192.168.0.47(rw,async,insecure,no_root_squash)

    Here the first IP address is the client's Ethernet address and the second
    IP address is the clients IPoIB address.

 Each time a machine boots:

  - Load and configure the RDMA drivers

    For InfiniBand using a Mellanox adapter:

    > modprobe ib_mthca
    > modprobe ib_ipoib
    > ifconfig ib0 a.b.c.d

    NOTE: use unique addresses for the client and server

  - Start the NFS server

    If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config),
    load the RDMA transport module:

    > modprobe svcrdma

    Regardless of how the server was built (module or built-in), start the server:

    > /etc/init.d/nfs start

    or

    > service nfs start

    Instruct the server to listen on the RDMA transport:

    > echo rdma 2050 > /proc/fs/nfsd/portlist

  - On the client system

    If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config),
    load the RDMA client module:

    > modprobe xprtrdma.ko

    Regardless of how the client was built (module or built-in), issue the mount.nfs command:

    > /path/to/your/mount.nfs <IPoIB-server-name-or-address>:/<export> /mnt -i -o rdma,port=2050

    To verify that the mount is using RDMA, run "cat /proc/mounts" and check the
    "proto" field for the given mount.

  Congratulations! You're using NFS/RDMA!
Commit	Line	Data
a3fa73bd JL	1	################################################################################
	2	# #
	3	# NFS/RDMA README #
	4	# #
	5	################################################################################
	6
	7	Author: NetApp and Open Grid Computing
	8	Date: February 25, 2008
	9
	10	Table of Contents
	11	~~~~~~~~~~~~~~~~~
	12	- Overview
	13	- Getting Help
	14	- Installation
	15	- Check RDMA and NFS Setup
	16	- NFS/RDMA Setup
	17
	18	Overview
	19	~~~~~~~~
	20
	21	This document describes how to install and setup the Linux NFS/RDMA client
	22	and server software.
	23
	24	The NFS/RDMA client was first included in Linux 2.6.24. The NFS/RDMA server
	25	was first included in the following release, Linux 2.6.25.
	26
	27	In our testing, we have obtained excellent performance results (full 10Gbit
	28	wire bandwidth at minimal client CPU) under many workloads. The code passes
	29	the full Connectathon test suite and operates over both Infiniband and iWARP
	30	RDMA adapters.
	31
	32	Getting Help
	33	~~~~~~~~~~~~
	34
	35	If you get stuck, you can ask questions on the
	36
	37	nfs-rdma-devel@lists.sourceforge.net
	38
	39	mailing list.
	40
	41	Installation
	42	~~~~~~~~~~~~
	43
	44	These instructions are a step by step guide to building a machine for
	45	use with NFS/RDMA.
	46
	47	- Install an RDMA device
	48
	49	Any device supported by the drivers in drivers/infiniband/hw is acceptable.
	50
	51	Testing has been performed using several Mellanox-based IB cards, the
	52	Ammasso AMS1100 iWARP adapter, and the Chelsio cxgb3 iWARP adapter.
	53
	54	- Install a Linux distribution and tools
	55
	56	The first kernel release to contain both the NFS/RDMA client and server was
	57	Linux 2.6.25 Therefore, a distribution compatible with this and subsequent
	58	Linux kernel release should be installed.
	59
	60	The procedures described in this document have been tested with
	61	distributions from Red Hat's Fedora Project (http://fedora.redhat.com/).
	62
	63	- Install nfs-utils-1.1.1 or greater on the client
	64
65	An NFS/RDMA mount point can only be obtained by using the mount.nfs
66	command in nfs-utils-1.1.1 or greater. To see which version of mount.nfs
67	you are using, type:
68
69	> /sbin/mount.nfs -V
70
71	If the version is less than 1.1.1 or the command does not exist,
72	then you will need to install the latest version of nfs-utils.
73
74	Download the latest package from:
75
76	http://www.kernel.org/pub/linux/utils/nfs
77
78	Uncompress the package and follow the installation instructions.
79
80	If you will not be using GSS and NFSv4, the installation process
81	can be simplified by disabling these features when running configure:
82
83	> ./configure --disable-gss --disable-nfsv4
84
85	For more information on this see the package's README and INSTALL files.
86
87	After building the nfs-utils package, there will be a mount.nfs binary in
88	the utils/mount directory. This binary can be used to initiate NFS v2, v3,
89	or v4 mounts. To initiate a v4 mount, the binary must be called mount.nfs4.
90	The standard technique is to create a symlink called mount.nfs4 to mount.nfs.
91
92	NOTE: mount.nfs and therefore nfs-utils-1.1.1 or greater is only needed
93	on the NFS client machine. You do not need this specific version of
94	nfs-utils on the server. Furthermore, only the mount.nfs command from
95	nfs-utils-1.1.1 is needed on the client.
96
97	- Install a Linux kernel with NFS/RDMA
98
99	The NFS/RDMA client and server are both included in the mainline Linux
100	kernel version 2.6.25 and later. This and other versions of the 2.6 Linux
101	kernel can be found at:
102
103	ftp://ftp.kernel.org/pub/linux/kernel/v2.6/
104
105	Download the sources and place them in an appropriate location.
106
107	- Configure the RDMA stack
108
109	Make sure your kernel configuration has RDMA support enabled. Under
110	Device Drivers -> InfiniBand support, update the kernel configuration
111	to enable InfiniBand support [NOTE: the option name is misleading. Enabling
112	InfiniBand support is required for all RDMA devices (IB, iWARP, etc.)].
113
114	Enable the appropriate IB HCA support (mlx4, mthca, ehca, ipath, etc.) or
115	iWARP adapter support (amso, cxgb3, etc.).
116
117	If you are using InfiniBand, be sure to enable IP-over-InfiniBand support.
118
119	- Configure the NFS client and server
120
121	Your kernel configuration must also have NFS file system support and/or
122	NFS server support enabled. These and other NFS related configuration
123	options can be found under File Systems -> Network File Systems.
124
125	- Build, install, reboot
126
127	The NFS/RDMA code will be enabled automatically if NFS and RDMA
128	are turned on. The NFS/RDMA client and server are configured via the hidden
129	SUNRPC_XPRT_RDMA config option that depends on SUNRPC and INFINIBAND. The
130	value of SUNRPC_XPRT_RDMA will be:
131
132	- N if either SUNRPC or INFINIBAND are N, in this case the NFS/RDMA client
133	and server will not be built
134	- M if both SUNRPC and INFINIBAND are on (M or Y) and at least one is M,
135	in this case the NFS/RDMA client and server will be built as modules
136	- Y if both SUNRPC and INFINIBAND are Y, in this case the NFS/RDMA client
137	and server will be built into the kernel
138
139	Therefore, if you have followed the steps above and turned no NFS and RDMA,
140	the NFS/RDMA client and server will be built.
141
142	Build a new kernel, install it, boot it.
143
144	Check RDMA and NFS Setup
145	~~~~~~~~~~~~~~~~~~~~~~~~
146
147	Before configuring the NFS/RDMA software, it is a good idea to test
148	your new kernel to ensure that the kernel is working correctly.
149	In particular, it is a good idea to verify that the RDMA stack
150	is functioning as expected and standard NFS over TCP/IP and/or UDP/IP
151	is working properly.
152
153	- Check RDMA Setup
154
155	If you built the RDMA components as modules, load them at
156	this time. For example, if you are using a Mellanox Tavor/Sinai/Arbel
157	card:
158
159	> modprobe ib_mthca
160	> modprobe ib_ipoib
161
162	If you are using InfiniBand, make sure there is a Subnet Manager (SM)
163	running on the network. If your IB switch has an embedded SM, you can
164	use it. Otherwise, you will need to run an SM, such as OpenSM, on one
165	of your end nodes.
166
167	If an SM is running on your network, you should see the following:
168
169	> cat /sys/class/infiniband/driverX/ports/1/state
170	4: ACTIVE
171
172	where driverX is mthca0, ipath5, ehca3, etc.
173
174	To further test the InfiniBand software stack, use IPoIB (this
175	assumes you have two IB hosts named host1 and host2):
176
177	host1> ifconfig ib0 a.b.c.x
178	host2> ifconfig ib0 a.b.c.y
179	host1> ping a.b.c.y
180	host2> ping a.b.c.x
181
182	For other device types, follow the appropriate procedures.
183
184	- Check NFS Setup
185
186	For the NFS components enabled above (client and/or server),
187	test their functionality over standard Ethernet using TCP/IP or UDP/IP.
188
189	NFS/RDMA Setup
190	~~~~~~~~~~~~~~
191
192	We recommend that you use two machines, one to act as the client and
193	one to act as the server.
194
195	One time configuration:
196
197	- On the server system, configure the /etc/exports file and
198	start the NFS/RDMA server.
199
200	Exports entries with the following format have been tested:
201
202	/vol0 10.97.103.47(rw,async) 192.168.0.47(rw,async,insecure,no_root_squash)
203
204	Here the first IP address is the client's Ethernet address and the second
205	IP address is the clients IPoIB address.
206
207	Each time a machine boots:
208
209	- Load and configure the RDMA drivers
210
211	For InfiniBand using a Mellanox adapter:
212
213	> modprobe ib_mthca
214	> modprobe ib_ipoib
215	> ifconfig ib0 a.b.c.d
216
217	NOTE: use unique addresses for the client and server
218
219	- Start the NFS server
220
221	If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config),
222	load the RDMA transport module:
223
224	> modprobe svcrdma
225
226	Regardless of how the server was built (module or built-in), start the server:
227
228	> /etc/init.d/nfs start
229
230	or
231
232	> service nfs start
233
234	Instruct the server to listen on the RDMA transport:
235
236	> echo rdma 2050 > /proc/fs/nfsd/portlist
237
238	- On the client system
239
240	If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config),
241	load the RDMA client module:
242
243	> modprobe xprtrdma.ko
244
245	Regardless of how the client was built (module or built-in), issue the mount.nfs command:
246
247	> /path/to/your/mount.nfs <IPoIB-server-name-or-address>:/<export> /mnt -i -o rdma,port=2050
248
249	To verify that the mount is using RDMA, run "cat /proc/mounts" and check the
250	"proto" field for the given mount.
251
252	Congratulations! You're using NFS/RDMA!