projects / linux-block.git / blame
| Commit | Line | Data |
|---|---|---|
| cd900f18 ML |
1 | What: /sys/class/power_supply/ltc4162-l/charge_status |
| 2 | Date: Januari 2021 | |
| 3 | KernelVersion: 5.11 | |
| 4 | Description: | |
| 5 | Detailed charge status information as reported by the chip. | |
| 6 | ||
| 7 | Access: Read | |
| 8 | ||
| 9 | Valid values: | |
| 10 | ilim_reg_active | |
| 11 | thermal_reg_active | |
| 12 | vin_uvcl_active | |
| 13 | iin_limit_active | |
| 14 | constant_current | |
| 15 | constant_voltage | |
| 16 | charger_off | |
| 17 | ||
| 18 | What: /sys/class/power_supply/ltc4162-l/ibat | |
| 19 | Date: Januari 2021 | |
| 20 | KernelVersion: 5.11 | |
| 21 | Description: | |
| 22 | Battery input current as measured by the charger. Negative value | |
| 23 | means that the battery is discharging. | |
| 24 | ||
| 25 | Access: Read | |
| 26 | ||
| 27 | Valid values: Signed value in microamps | |
| 28 | ||
| 29 | What: /sys/class/power_supply/ltc4162-l/vbat | |
| 30 | Date: Januari 2021 | |
| 31 | KernelVersion: 5.11 | |
| 32 | Description: | |
| 33 | Battery voltage as measured by the charger. | |
| 34 | ||
| 35 | Access: Read | |
| 36 | ||
| 37 | Valid values: In microvolts | |
| 38 | ||
| 39 | What: /sys/class/power_supply/ltc4162-l/vbat_avg | |
| 40 | Date: Januari 2021 | |
| 41 | KernelVersion: 5.11 | |
| 42 | Description: | |
| 43 | Battery voltage, averaged over time, as measured by the charger. | |
| 44 | ||
| 45 | Access: Read | |
| 46 | ||
| 47 | Valid values: In microvolts | |
| 48 | ||
| 49 | What: /sys/class/power_supply/ltc4162-l/force_telemetry | |
| 50 | Date: Januari 2021 | |
| 51 | KernelVersion: 5.11 | |
| 52 | Description: | |
| 53 | To save battery current, the measurement system is disabled if | |
| 54 | the battery is the only source of power. This affects all | |
| 55 | voltage, current and temperature measurements. | |
| 56 | Write a "1" to this to keep performing telemetry once every few | |
| 57 | seconds, even when running on battery (as reported by the online | |
| 58 | property, which is "1" when external power is available and "0" | |
| 59 | when the system runs on battery). | |
| 60 | ||
| 61 | Access: Read, Write | |
| 62 | ||
| 63 | Valid values: 0 (disabled) or 1 (enabled) | |
| 64 | ||
| 65 | What: /sys/class/power_supply/ltc4162-l/arm_ship_mode | |
| 66 | Date: Januari 2021 | |
| 67 | KernelVersion: 5.11 | |
| 68 | Description: | |
| 69 | The charger will normally drain the battery while inactive, | |
| 70 | typically drawing about 54 microamps. Write a "1" to this | |
| 71 | property to arm a special "ship" mode that extends shelf life | |
| 72 | by reducing the leakage to about 2.8 microamps. The chip will | |
| 73 | remain in this mode (and no longer respond to I2C commands) | |
| 74 | until some external power-supply is attached raising the input | |
| 75 | voltage above 1V. It will then automatically revert to "0". | |
| 76 | Writing a "0" to the property cancels the "ship" mode request. | |
| 77 | The ship mode, when armed, activates once the input voltage | |
| 78 | drops below 1V. | |
| 79 | ||
| 80 | Access: Read, Write | |
| 81 | ||
| 82 | Valid values: 0 (disable) or 1 (enable) |