drm/i915: Beef up skl_sanitize_cdclk() a bit

Also verify the DPLL_CTRL1 register value in skl_sanitize_cdclk(), throw
out a few unneeded variables, and write the CDCLK_CTL check a bit more
legible way.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Keep track of preferred cdclk vco frequency on SKL

Now that skl_vco_freq tracks the actual DPLL0 vco frequency, we'll need
something that keeps track of which vco frequency we want to use in case
the current vco is 0. This would be important across supend/resume since
we'll disable DPLL0 around those parts.

We'll also update our idea of max cdclk/dotclock when the preferred
vco changes. That could happen if out initial guess was wrong, and
later eDP would force us to change it. One issue here could be that
changing the max dotclock could cause our mode list to change during
next time the displays get probed. But I don't see a good way to avoid
that, except perhaps by allowing either vco frequency to be used as
needed. But the docs suggest that such usage wasn't really inteded.

Also need to make sure we don't update our max_cdclk value before we
have a preferred vco value, which means moving that to happen after
the cdclk sanitation.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Allow enable/disable of DPLL0 around cdclk changes on SKL

In case we originally guessed wrong which lcpll vco frequency to use,
we will need to shut down the pll and restart it when reprogamming the
cdclk.

This also allows us to track the actual vco frequency in dev_priv
instead of just a guess.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Report the current DPLL0 vco on SKL/KBL

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Actually read out DPLL0 vco on skl from hardware

Currently we're trying to guess which lcpll vco frequency is used
use based on the cdclk. That doesn't work for cdclk==540 since
both vco frequencies can generate a 540 Mhz output. Let's stop
guessing and just read the actual vco frequency from the
hardware.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Extract skl_calc_cdclk()

We have many places where we want to pick a suitable cdclk frequency for
skl based on the dotclock and lcpll vco. Split that code into a small
helper and call it from all over.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Move the SKL DPLL0 VCO computation into intel_dp_compute_config()

Shared plls won't get assigned until the .compute_clocks() hook gets
called, which happens from the crtc .atomic_check hook. That's too late
as the cdclk computation has already happened. So let's move the DPLL0
VCO computation into intel_dp_compute_config() so that it's done when
the cdclk computation happens. Also only do it for eDP since we only
pick DPLL0 for eDP.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/skl: SKL CDCLK change on modeset tracking VCO

WARNING: Using ChromeOS with an eDP panel and a 4K@60 DP monitor connected
to DDI1 the system will hard hang during a cold boot. Occurs when DDI1
is enabled when the cdclk is less then required. DP connected to DDI2
and HPD on either port works correctly.

Set cdclk based on the max required pixel clock based on VCO
selected. Track boot vco instead of boot cdclk.

The vco is now tracked at the atomic level and all CRTCs updated if
the required vco is changed. Not tested with eDP v1.4 panels that
require 8640 vco due to availability.

V1: initial version
V2: add vco tracking in intel_dp_compute_config(), rename
skl_boot_cdclk.
V3: rebase, V2 feedback not possible as encoders are not aware of
atomic.
V4: track target vco is atomic state. modeset all CRTCs if vco changes
V5: rename atomic variable, cleaner if/else logic, use existing vco if
      encoder does not return a new vco value. check_patch.pl cleanup
V6: simplify logic in intel_modeset_checks.
V7: reorder an IF for readability and whitespace fix.
V8: use dev_cdclk for tracking new cdclk during atomic
V9: correctly handle vco 8640 when crtcs==0
V10: Clean up if else in crtcs==0
V11: Rebase for new intel_dpll_mgr.c

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
[vsyrjala: rebased due to churn]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-3-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Fix BXT min_pixclk after state readout

commit 4e5ca60fd35a ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
tried to change BXT to use ilk_max_pixel_rate() to compute the
pipe pixel rate. I failed to notice that there was another place
in the state readout code that needs the same treatment. So let's
change that one too.

Should probably just change things to always compuyte the pipe pixel
rates, instead of just doing on platforms that can change cdclk
dynamically. But for now let's just move BXT fully over to the
side that uses ilk_pipe_pixel_rate().

Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 4e5ca60fd35a ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/opregion: Rename init/fini functions to register/unregister

Current intel_opregion_init is called during the driver registration
phase and intel_opregion_fini from the unregistration phase. Rename the
functions so that this is clear from their names. The phases tell us
what we expect the existing hw state to be, e.g. whether interrupts are
still enabled etc.

It should be noted that the opregion init/fini routines are asymmetric
and this is carried across into their new names. Indeed, their new names
make it even clearer that perhaps all is not well in the opregion
suspend/resume sequence (as well in the module unload).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>

drm/i915/opregion: Convert to using native drm_i915_private

Prefer passing struct drm_i915_private to internal interfaces as this
saves us having to dance between drm_device and our native struct. The
savings hare are small (only 70 bytes of unrequired dancing), but
progressive!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>

drm/i915: Enable GSE interrupt on BDW+

We've never actually enabled or unmasked the GSE interrupt on BDW+,
even though the interrupt handler was always prepared for it.
Let's enable it and see what happens.

Credit to Mark Kettenis who fixed this in the OpenBSD fork of the
driver. He reports that it fixed the "ACPI _BCM/_BCQ-based
brightness mechanism on a MacBookPro12,1 and a 3rd gen Lenovo X1
Carbon" for them.

Mark says:
"FWIW, this *is* needed if you want ACPI-based backlight control to
 work.  On Linux you probably don't notice, since "hardware" backlight
 control is preferred over "firmware" or "platform" backlight control.

 It would help me if this did land in the Linux tree though, as it will
 make future imports of the i915 driver into OpenBSD easier."

So even though we don't really need this, let's put it in to help Mark
with future porting efforts. Should be harmless to have it enabled in
any case.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/081799.html
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Cc: Mark Kettenis <mark.kettenis@xs4all.nl>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463649283-28698-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/guc: rework guc_add_workqueue_item()

Mostly little optimisations and future-proofing against code breakage.
For instance, if the driver is correctly following the submission
protocol, the "out of space" condition is impossible, so the previous
runtime WARN_ON() is promoted to a GEM_BUG_ON() for a more dramatic
effect in development and less impact in end-user systems.

Similarly we can make alignment checking more stringent and replace
other WARN_ON() conditions that don't relate to the runtime hardware
state with either BUILD_BUG_ON() for compile-time-detectable issues, or
GEM_BUG_ON() for logical "can't happen" errors.

With those changes, we can convert it to void, as suggested by Chris
Wilson, and update the calling code appropriately.

v2:
    Note that we're now putting the request seqno in the "fence_id"
    field of each GuC-work-item, in case it turns up somewhere useful
    (e.g. in a GuC log) [Tvrtko Ursulin].

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/guc: don't spinwait if the GuC's workqueue is full

Rather than wait to see whether more space becomes available in the GuC
submission workqueue, we can just return -EAGAIN and let the caller try
again in a little while. This gets rid of an uninterruptable sleep in
the polling code :)

We'll also add a counter to the GuC client statistics, to see how often
we find the WQ full.

v2:
    Flag the likely() code path (Tvtrko Ursulin).

v4:
    Add/update comments about failure counters (Tvtrko Ursulin).

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/guc: pass request (not client) to i915_guc_{wq_check_space, submit}()

The knowledge of how to derive the relevant client from the request
should be localised within i915_guc_submission.c; the LRC code shouldn't
have to know about the internal details of the GuC submission process.
And all the information the GuC code needs should be encapsulated in (or
reachable from) the request.

v2:
    GEM_BUG_ON() for bad GuC client (Tvrtko Ursulin).
    Add/update kerneldoc explaining check_space/submit protocol

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/guc: add enable_guc_loading parameter

Split the function of "enable_guc_submission" into two separate
options.  The new one ("enable_guc_loading") controls only the
*fetching and loading* of the GuC firmware image. The existing
one is redefined to control only the *use* of the GuC for batch
submission once the firmware is loaded.

In addition, the degree of control has been refined from a simple
bool to an integer key, allowing several options:
-1 (default)     whatever the platform default is
 0  DISABLE      don't load/use the GuC
 1  BEST EFFORT  try to load/use the GuC, fallback if not available
 2  REQUIRE      must load/use the GuC, else leave the GPU wedged

The new platform default (as coded here) will be to attempt to
load the GuC iff the device has a GuC that requires firmware,
but not yet to use it for submission. A later patch will change
to enable it if appropriate.

v4:
    Changed some error-message levels, mostly ERROR->INFO, per
    review comments by Tvrtko Ursulin.

v5:
    Dropped one more error message, disabled GuC submission on
    hypothetical firmware-free devices [Tvrtko Ursulin].

v6:
    Logging tidy by Tvrtko Ursulin:
     * Do not log falling back to execlists when wedging the GPU.
     * Do not log fw load errors when load was disabled by user.
     * Pass down some error code from fw load for log message to
       make more sense.

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Fiedorowicz, Lukasz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com> (v6)

drm/i915/guc: distinguish HAS_GUC() from HAS_GUC_UCODE/HAS_GUC_SCHED

For now, anything with a GuC requires uCode loading, and then supports
command submission once loaded. But these are logically distinct from
simply "having a GuC", so we need a separate macro for the latter. Then,
various tests should use this new macro rather than HAS_GUC_UCODE() or
testing enable_guc_submission.

v4:
    Added a couple more uses of the new macro.

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/guc: rename loader entry points

The GuC initialisation code could do other things apart from loading
firmware, so here we rename the three primary entry points to remove any
specific reference to "ucode" (no functional changes, just renaming).

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Update DRIVER_DATE to 20160522

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Inline sg_next() for the optimised SGL iterator

Avoiding the out-of-line call to sg_next() reduces the kernel execution
overhead by 10% in some workloads (for example the Unreal Engine 4 demo
Atlantis on 2GiB GTTs) which are dominated by the cost of inserting PTEs
due to texture thrashing. We can demonstrate this in a microbenchmark
that forces us to rebind the object on every execbuf, where we can
measure a 25% improvement, in the time required to execute an execbuf
requiring a texture to be rebound, for inlining the sg_next() for large
texture sizes.

Benchmark: igt/benchmarks/gem_exec_fault
Benchmark: igt/benchmarks/gem_exec_trace/Atlantis
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-5-git-send-email-chris@chris-wilson.co.uk

drm/i915: Introduce & use new lightweight SGL iterators

The existing for_each_sg_page() iterator is somewhat heavyweight, and is
limiting i915 driver performance in a few benchmarks. So here we
introduce somewhat lighter weight iterators, primarily for use with GEM
objects or other case where we need only deal with whole aligned pages.

Unlike the old iterator, the new iterators use an internal state
structure which is not intended to be accessed by the caller; instead
each takes as a parameter an output variable which is set before each
iteration. This makes them particularly simple to use :)

One of the new iterators provides the caller with the DMA address of
each page in turn; the other provides the 'struct page' pointer required
by many memory management operations.

Various uses of for_each_sg_page() are then converted to the new macros.

v2: Force inlining of the sg_iter constructor and make the union
anonymous.

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-4-git-send-email-chris@chris-wilson.co.uk

drm/i915: optimise i915_gem_object_map() for small objects

We're using this function for ringbuffers and other "small" objects, so
it's worth avoiding an extra malloc()/free() cycle if the page array is
small enough to put on the stack. Here we've chosen an arbitrary cutoff
of 32 (4k) pages, which is big enough for a ringbuffer (4 pages) or a
context image (currently up to 22 pages).

v5:
    change name of local array [Chris Wilson]

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-3-git-send-email-chris@chris-wilson.co.uk

drm/i915: refactor i915_gem_object_pin_map()

The recently-added i915_gem_object_pin_map() can be further optimised
for "small" objects. To facilitate this, and simplify the error paths
before adding the new code, this patch pulls out the "mapping" part of
the operation (involving local allocations which must be undone before
return) into its own subfunction.

The next patch will then insert the new optimisation into the middle of
the now-separated subfunction.

This reorganisation will probably not affect the generated code, as the
compiler will most likely inline it anyway, but it makes the logical
structure a bit clearer and easier to modify.

v2:
    Restructure loop-over-pages & error check [Chris Wilson]

v3:
    Add page count to debug messages [Chris Wilson]
    Convert WARN_ON() to GEM_BUG_ON()

v4:
    Drop the DEBUG messages [Tvrtko Ursulin]

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-2-git-send-email-chris@chris-wilson.co.uk

drm/i915/psr: Implement PSR2 w/a for gen9

Found this while browsing Bspec. Looks like it applies to both skl and
kbl.

v2: Also for bxt (Art).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch

drm/i915/psr: Use ->get_aux_send_ctl functions

I just wanted to get rid of the rmw cycle for gen9, but this also
fixes some bugs we haven't carried over, like using recommended
precharge and timeout values.

Also I noticed that we don't set the fastwake sync length on skl, and
that's used by PSR2 selective updates. Fix that.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-6-git-send-email-daniel.vetter@ffwll.ch

drm/i915/psr: Order DP aux transactions correctly

On bdw/hsw we have a separate psr dp aux registers to set up, but on
bdw it's shared with the main dp aux thing. Which means any subsequent
dp aux transaction will trample over it, and hence must be done
beforehand.

Also this means we can't do any dp aux transactions while PSR is
active, or at least we must restore the old state.

Probably need a psr disable/enable pair around dp aux transactions in
general.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-5-git-send-email-daniel.vetter@ffwll.ch

drm/i915/psr: Make idle_frames sensible again

This reverts

commit dfaf37baa07513d2c37afff79978807d2d10221a
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date:   Mon Dec 7 14:45:20 2015 -0800

    drm/i915: Fix idle_frames counter.

and

commit 97173eaf5f33b1e85efdb06d593d333480b60bf3
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date:   Tue Jul 7 16:28:55 2015 -0700

    drm/i915: PSR: Increase idle_frames

and implements

commit d44b4dcbd1b44737462b77971d216d21a9413341
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date:   Fri Nov 14 08:52:31 2014 -0800

    drm/i915: HSW/BDW PSR Set idle_frames = VBT + 1

without the hack to use 2 idle frames when VBT says 1. We keep the + 1
just for safety, although I haven't really figured out why that one
exists.

It's nonsense. idle_frames = number of frames where the screen is
entirely idle before we think about entering PSR.

idle_patter = part of link training, and we probably totally butchered
link training because we told the hw to entirely skip it. No wonder
PSR occasionally just fell over.

I suspect the reason we've increased idle frames is that it makes PSR
entry slightly less likely, and more likely to happen in a quite
system, which probably increased the changes the panel came back up
without link training. The proper fix is to implement link training
for PSR.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-3-git-send-email-daniel.vetter@ffwll.ch

drm/i915/psr: Try to program link training times correctly

The default of 0 is 500us of link training, but that's not enough for
some platforms. Decoding this correctly means we're using 2.5ms of
link training on these platforms, which fixes flickering issues
associated with enabling PSR.

v2: Unbotch the math a bit.

v3: Drop debug hunk.

v4: Improve commit message.

Tested-by: Lyude <cpaul@redhat.com>
Cc: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: fritsch@kodi.tv
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-2-git-send-email-daniel.vetter@ffwll.ch

drm/i915/userptr: Convert to drm_i915_private

userptr directly only uses drm_device in a single interface where it
meant to use drm_i915_private (everywhere else we have to derive it from
the drm_i915_gem_object and so require going from drm_device).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463671036-3235-1-git-send-email-chris@chris-wilson.co.uk

drm/i915: Allow nonblocking update of pageflips.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-22-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Check for unpin correctness.

If planes are added to the state after the call to
drm_atomic_helper_check_planes planes_changed may not be set
and we will not unpin the old framebuffer. This results in a
pin leak long after the framebuffer is destroyed, so to find
this add some checks when it happens.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-21-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"

This reapplies commit acf4e84d6167317ff21be5c03e1ea76ea5783701.
With async unpin this should no longer break.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-20-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Make unpin async.

All of intel_post_plane_update is handled there now, so move it over.
This is run after the hw state checker because it can't handle checking
crtc's separately yet.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-19-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Prepare connectors for nonblocking checks.

intel_unpin_work may not take the list lock because it requires the connector_mutex.
To prevent taking locks we add an array of old and new state. The old state to free,
the new state to commit and verify.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-18-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Pass atomic states to fbc update functions.

This is required to let fbc updates run async. It has a lot of
checks whether certain locks are taken, which can be removed when
the relevant states are passed in as pointers.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-17-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove reset_counter from intel_crtc.

With the removal of cs-based flips all mmio waits will
finish without requiring the reset counter, because the
waits will complete during gpu reset.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-16-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove queue_flip pointer.

With the removal of cs support this is no longer reachable.
Can be revived if needed.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-15-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove use_mmio_flip kernel parameter.

With the removal of cs flips this is always force enabled.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-14-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove cs based page flip support.

With mmio flips now available on all platforms it's time to remove
support for cs flips.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-13-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.

Create a work structure that will be used for all changes. This will
be used later on in the atomic commit function.

Changes since v1:
- Free old_crtc_state from unpin_work_fn properly.
Changes since v2:
- Add hunk for calling hw state verifier.
- Add missing support for color spaces.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-12-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Add the exclusive fence to plane_state.

Set plane_state->base.fence to the dma_buf exclusive fence,
and add a wait to the mmio function. This will make it easier
to unify plane updates later on.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-11-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Convert flip_work to a list.

This will be required to allow more than 1 update in the future.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-10-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Allow mmio updates on all platforms, v2.

With intel_pipe_update begin/end we ensure that the mmio updates
don't run during vblank interrupt, using the hw counter we can
be sure that when current vblank count != vblank count at the time
of pipe_update_end the mmio update is complete.

This allows us to use mmio updates on all platforms, using the
update_plane call.

With Chris Wilson's patch to skip waiting for vblanks for
legacy_cursor_update this potentially leaves a small race
condition, in which update_plane can be called with a freed
crtc_state. Because of this commit acf4e84d61673
("drm/i915: Avoid stalling on pending flips for legacy cursor updates")
is temporarily reverted.

Changes since v1:
- Split out the flip_work rename.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"

This reverts commit acf4e84d6167317ff21be5c03e1ea76ea5783701.
Unfortunately this breaks the next commit with a use-after-free, so
temporarily revert until we can apply a solution.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-8-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Unify unpin_work and mmio_work into flip_work, v2.

Rename intel_unpin_work to intel_flip_work and use it for mmio flips
and unpinning. Use flip_queued_req to hold the wait request in the
mmio case, and the vblank counter from intel_crtc_get_vblank_counter.

MMIO flips get their own path through intel_finish_page_flip_mmio,
handled on vblank. CS page flips go through *_cs.

Changes since v1:
- Clean up destinction between MMIO and CS flips.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-7-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Add support for detecting vblanks when hw frame counter is unavailable.

This uses the newly created drm_accurate_vblank_count_and_time to accurately
get a vblank count when the hw counter is unavailable.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-6-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove intel_prepare_page_flip, v3.

Instead of calling prepare_flip right before calling finish_page_flip
do everything from prepare_page_flip in finish_page_flip.

Putting prepare and finish page_flip in a single step removes the need
for INTEL_FLIP_COMPLETE, so it can be removed. This simplifies the code
slightly.

Changes since v1:
- Invert if case to simplify code.
- Add missing barrier.
- Reword commit message.
Changes since v2:
- intel_page_flip_plane is removed.
- work->pending is turned into a bool.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove intel_finish_page_flip_plane.

This function is duplicated with intel_finish_page_flip,
and is only ever used from planes that could use the
other function anyway.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-4-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove stallcheck special handling, v3.

Both intel_unpin_work.pending and intel_unpin_work.enable_stall_check
were used to see if work should be enabled. By only using pending
some special cases are gone, and access to unpin_work can be simplified.

A flip could previously be queued before
stallcheck was active. With the addition of the pending member
enable_stall_check became obsolete and can thus be removed.

Use this to only access work members untilintel_mark_page_flip_active
is called, or intel_queue_mmio_flip is used. This will prevent
use-after-free, and makes it easier to verify accesses.

Changes since v1:
- Reword commit message.
- Do not access unpin_work after intel_mark_page_flip_active.
- Add the right memory barriers.
Changes since v2:
- atomic_read() needs a full smp_rmb.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/core: Add drm_accurate_vblank_count, v5.

This function is useful for gen2 intel devices which have no frame
counter, but need a way to determine the current vblank count without
racing with the vblank interrupt handler.

intel_pipe_update_start checks if no vblank interrupt will occur
during vblank evasion, but cannot check whether the vblank handler has
run to completion. This function uses the timestamps to determine
when the last vblank has happened, and interpolates from there.

Changes since v1:
- Take vblank_time_lock and don't use drm_vblank_count_and_time.
Changes since v2:
- Don't return time of last vblank.
Changes since v3:
- Change pipe to unsigned int. (Ville)
- Remove unused documentation for tv_ret. (kbuild)
Changes since v4:
- Add warning to docs when the function is useful.
- Add a WARN_ON when get_vblank_timestamp is unavailable.
- Use drm_vblank_count.

Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v4
Acked-by: David Airlie <airlied@linux.ie> #irc, v4
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>

drm/i915/bxt: reserve space for RC6 in the the GuC WOPCM

This patch resizes the GuC WOPCM (specifically on BXT)
so that the GuC and RC6 memory spaces do not overlap.

v2:
    Made calculation of WOPCM size into a separate function,
    so that it's consistent between the firmware size-check
    and the register-programming operations [Dave Gordon].

Issue: https://jira01.devtools.intel.com/browse/VIZ-6638
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Tested-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463494365-26330-1-git-send-email-david.s.gordon@intel.com

drm/i915: Simplify control flow in intel_atomic_check a bit.

- Unconditionally add plane states. Core helpers would have done this
  in drm_atomic_helper_check_modeset, doing it once more won't cause
  harm and is less fragile.

- Simplify the continue logic when disabling a pipe.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462779085-2458-1-git-send-email-daniel.vetter@ffwll.ch

drm/i915/dsi: CABC support for Panel PWM backlight control

In CABC (Content Adaptive Brightness Control) content grey level
scale can be increased while simultaneously decreasing
brightness of the backlight to achieve same perceived brightness.

The CABC is not standardized and panel vendors are free to follow
their implementation. The CABC implementaion here assumes that the
panels use standard SW register for control.

CABC is supported only when the PWM source for backlight is
from the panel.

v2 by Jani: rebase, renames, check cabc support earlier, etc.

Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/883faade74d2e598b143221ccc7df6daf4393a13.1461676337.git.jani.nikula@intel.com

drm/i915/dsi: Add DCS control for Panel PWM

If the source of the backlight PWM is from the
panel then the PWM can be controlled by DCS
command, this patch adds the support to
enable/disbale panel PWM, control backlight level
etc...

v2: Moving the CABC bkl functions to new file.(Jani)

v3: Rebase

v4: Rebase

v5: Use mipi_dsi_dcs_write() instead of mipi_dsi_dcs_write_buffer() (Jani)
    Move DCS macro`s to include/video/mipi_display.h (Jani)

v6: Rename the file to intel_dsi_panel_pwm.c
    Removing the CABC operations

v7 by Jani: renames, rebases, etc.

v8 by Jani: s/INTEL_BACKLIGHT_CABC/INTEL_BACKLIGHT_DSI_DCS/

v9 by Jani: rename init function to intel_dsi_dcs_init_backlight_funcs

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/71238a4b14b8c3a6c04070c789f09f1b4bc00a15.1461676337.git.jani.nikula@intel.com

Merge remote-tracking branch 'airlied/drm-next' into drm-intel-next-queued

Backmerge request by Jani to get at

commit 249c4f538b1aae55d41699f8bafc6cb762a7f48f
Author: Deepak M <m.deepak@intel.com>
Date:   Wed Mar 30 17:03:39 2016 +0300

    drm: Add new DCS commands in the enum list

Some simple conflicts in intel_dp.c.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

Merge tag 'topic/drm-misc-2016-05-13' of git://anongit.freedesktop.org/drm-intel into drm-next

I kinda hoped that I could still sneak in Noralf's
drm_simple_display_pipe, since there's intereset by others now (for tilcdc
at least). But it wasn't ready by a hair. Oh well.

Otherwise random stuff plus prep patches from Noralf.

* tag 'topic/drm-misc-2016-05-13' of git://anongit.freedesktop.org/drm-intel:
  drm/atomic: Add drm_atomic_helper_best_encoder()
  drm/atomic: Don't skip drm_bridge_*() calls if !drm_encoder_helper_funcs
  drm/fb-cma-helper: Hook up to DocBook and fix some docs
  drm/fb-helper: Remove mention of CONFIG_FB_DEFERRED_IO in docs
  drm/sti: include linux/seq_file.h where needed
  drm/tegra: Use lockless gem BO free callback
  drm/exynos: Use lockless gem BO free callback
  drm: Make drm_encoder_helper_funcs optional

Merge branch 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux into drm-next

Please pull this mini-series that allows ARC PGU to use
dedicated memory location as framebuffer backing storage.

* 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux:
  ARC: [axs10x] Specify reserved memory for frame buffer
  drm/arcpgu: use dedicated memory area for frame buffer

drm/i915: don't mix bitwise and logical operations for has_snoop

Also make the code more readable.

Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463148278-23193-2-git-send-email-jani.nikula@intel.com

drm/i915: Skip clearing the GGTT on full-ppgtt systems

Under full-ppgtt, access to the global GTT is carefully regulated
through hardware functions (i.e. userspace cannot read and write to
arbitrary locations in the GGTT via the GPU). With this restriction in
place, we can forgo clearing stale entries from the GGTT as they will
not be accessed.

For aliasing-ppgtt, we could almost do the same except that we do allow
userspace access to the global-GTT via execbuf in order to workraound
some quirks of certain instructions. (This execbuf path is filtered out
with EINVAL on full-ppgtt.)

The most dramatic effect this will have will be during resume, as with
full-ppgtt the GGTT is only used sparingly.

References: https://bugs.freedesktop.org/show_bug.cgi?id=94722
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-4-git-send-email-chris@chris-wilson.co.uk

drm/i915: Lazily migrate the objects after hibernation

Now that we mark the object domains for having been restored from the
hibernation image, we not need to flush everything during resume and
can instead rely on the normal domain tracking to flush only when
required. The only caveat here are objects that are pinned for use by
the hardware, whose contents must be coherent for when the device
resumes reading from then (shortly afterwards with the driver assuming
the objects are in the correct domain).

References: https://bugs.freedesktop.org/show_bug.cgi?id=94722
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-3-git-send-email-chris@chris-wilson.co.uk

drm/i915: Update domain tracking for GEM objects on hibernation

When creating the hibernation image, the CPU will read the pages of all
objects and thus conflict with our domain tracking. We need to update
our domain tracking to accurately reflect the state on restoration.

v2: Perform the domain tracking inside freeze, before the image is
written, rather than upon restoration.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-2-git-send-email-chris@chris-wilson.co.uk

drm/i915: Add distinct stubs for PM hibernation phases

Currently for handling the extra hibernation phases we just call the
equivalent suspend/resume phases. In the next couple of patches, I wish
to specialise the hibernation phases to reduce the amount of work
required for handling GEM objects.

v2: There are more! Don't forget the freeze phases.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-1-git-send-email-chris@chris-wilson.co.uk

drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)

When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.

In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.

Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.

v2:
 - Rebase; the SKL atomic WM patches that just landed changed the WM
   structure fields in intel_crtc_state slightly.  (Matt)

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca853 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com

drm/i915: Don't leave old junk in ilk active watermarks on readout

When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.

Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.

Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9ca ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Eliminate the CDCLK_CTL RMW on BXT

All the fields in CDCLK_CTL we don't program should be left at zero, so
let's just get rid of the RMW.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Program BXT_CDCLK_CD2X_PIPE

BXT could change the CD2X divider synchronized with a single pipe.
So assuming the DE PLL frequency doesn't need to be changed, we could
change cdclk without shutting off the pipe (when only a single pipe is
enabled). In the meantime let's configure CDCLK_CTL for non-double
buffered CD2X update, although it shouldn't really matter as long as
the selected pipe is disabled when reprogramming the divider.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: s/required_vco/vco/ in skl cdclk code

The 'required' part of 'required_vco' should be obvious. Let's just call
it 'vco' for brevity.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/freq/cdclk/

Rename the generic sounding freq/frequency parameters to the cdclk
functions to 'cdclk' so that we'll know which clock we're talking about
once we have to deal with the vco frequencies as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Kill off dead code from skl_dpll0_enable()

We calculate the CDCLK_CTL value from scratch so no need to attempt
some form of RMW first.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract skl_dpll0_disable()

Make thins a bit easier to read by extracting the SKL DPLL0
disable into separate functions. We already have the enable
counterpart. Down the line this will also help make the cdclk
programming on SKL, BXT, and following platforms look rather
consistent.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Remove 10% cdclk guardband on BXT

We don't need any pixel clock vs. cdclk guardband since HSW. BXT still
tries to add one though. Get rid of it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Use skl_cdclk_decimal() on bxt

Both SKL and BXT need to fill in the "decimal" cdclk frequency into
the CDCLK_CTL register. SKL uses a small helper to do the kHz->"decimal"
conversion, whereas BXT has it open-coded. Use the helper on BXT too.

While at it, change it to round to closest rather than down. It doesn't
actually matter with the frequencies we have to deal with, but it seems
like the right thing to do.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation

BXT uses the "pch" panel fitter configuration, so we can use
ilk_max_pixel_rate() instead of intel_mode_max_pixclk() to compute the
pipe pixel rate. ilk_max_pixel_rate() will account for the pipe
scaler downscaling factor whereas intel_mode_max_pixclk() will not.

I'm pretty sure the same limitation is there on GMCH platforms, but
no one just bothered to implement the downscaling adjustment for them.
Probably should just unify the panel fitter setup more across the
platforms and use the exact same code on all platforms for this.
But in the meantime, let's at least make BXT a bit more correct.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Don't pass dev_priv to broxton_calc_cdclk()

broxton_calc_cdclk() doesn't need dev_priv for anything, so let's not
bother passing it around.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Untangle .fdi_link_train and cdclk vfunc setup

Split the .fdi_link_train and .modeset_commit_cdclk/.modeset_calc_cdclk
into two separate if ladders. Much easier to read when you're not
confusing two totally separate subjects.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract broadwell_calc_cdclk()

Try to reduce the amount of duplicated cdclk magic numbers by
moving the max_pixclk->cdclk conversion into a helper.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Drop checks for max_pixclk failures in cdclk computation

commit 565602d7501a ("drm/i915: Do not acquire crtc state to check clock during modeset, v4.")
removed the possibility that intel_mode_max_pixclk() or
ilk_max_pixel_rate() might return an error, so let's get rid of the
error checks in the callers as well.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Remove wm_config from dev_priv/intel_atomic_state

We calculate the watermark config into intel_atomic_state and then save
it into dev_priv, but never actually use it from there.  This is
left-over from some early ILK-style watermark programming designs that
got changed over time.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-18-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Reject display updates that exceed wm limitations (v2)

If we can't find any valid level 0 watermark values for the requested
atomic transaction, reject the configuration before we try to start
programming the hardware.

v2:
 - Add extra debugging output when we reject level 0 watermarks so that
   we can more easily debug how/why they were rejected.

Cc: Lyude Paul <cpaul@redhat.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-17-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Calculate watermarks during atomic 'check' (v2)

Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).

Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction.  The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state.  That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time.  However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved).  With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).

We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.

v2:
 - Bail out of skl_write_wm_values() if the CRTC isn't active.  Now that
   we set dirty_pipes to ~0 if the active pipes change (because
   we need to deal with DDB changes), we can now wind up here for
   disabled pipes, whereas we couldn't before.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Propagate watermark calculation failures up the call chain

Once we move watermark calculation to the atomic check phase, we'll want
to start rejecting display configurations that exceed out watermark
limits.  At the moment we just assume that there's always a valid set of
watermarks, even though this may not actually be true.  Let's prepare by
passing return codes up through the call stack in preparation.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-15-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Use a bitmask to track dirty pipe watermarks

Slightly easier to work with than an array of bools.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-14-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Allow watermark calculation on in-flight atomic state (v3)

In an upcoming patch we'll move this calculation to the atomic 'check'
phase so that the display update can be rejected early if no valid
watermark programming is possible.

v2:
 - Drop intel_pstate_for_cstate_plane() helper and add note about how
   the code needs to evolve in the future if we start allowing more than
   one pending commit against a CRTC.  (Maarten)

v3:
 - Only have skl_compute_wm_level calculate watermarks for enabled
   planes; we can just set the other planes on a CRTC to disabled
   without having to look at the plane state.  This is important because
   despite our CRTC lock we can still have racing commits that modify
   a disabled plane's property without turning it on.  (Maarten)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-13-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Calculate plane WM's from state

In a future patch we'll want to calculate plane watermarks for in-flight
atomic state rather than the already-committed state.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-12-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Drop re-allocation of DDB at atomic commit (v2)

Now that we're properly pre-allocating the DDB during the atomic check
phase and we trust that the allocation is appropriate, let's actually
use the allocation computed and not duplicate that work during the
commit phase.

v2:
 - Significant rebasing now that we can use cached data rates and
   minimum block allocations to avoid grabbing additional plane states.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-11-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Compute DDB allocation at atomic check time (v4)

Calculate the DDB blocks needed to satisfy the current atomic
transaction at atomic check time.  This is a prerequisite to calculating
SKL watermarks during the 'check' phase and rejecting any configurations
that we can't find valid watermarks for.

Due to the nature of DDB allocation, it's possible for the addition of a
new CRTC to make the watermark configuration already in use on another,
unchanged CRTC become invalid.  A change in which CRTC's are active
triggers a recompute of the entire DDB, which unfortunately means we
need to disallow any other atomic commits from racing with such an
update.  If the active CRTC's change, we need to grab the lock on all
CRTC's and run all CRTC's through their 'check' handler to recompute and
re-check their per-CRTC DDB allocations.

Note that with this patch we only compute the DDB allocation but we
don't actually use the computed values during watermark programming yet.
For ease of review/testing/bisecting, we still recompute the DDB at
watermark programming time and just WARN() if it doesn't match the
precomputed values.  A future patch will switch over to using the
precomputed values once we're sure they're being properly computed.

Another clarifying note:  DDB allocation itself shouldn't ever fail with
the algorithm we use today (i.e., we have enough DDB blocks on BXT to
support the minimum needs of the worst-case scenario of every pipe/plane
enabled at full size).  However the watermarks calculations based on the
DDB may fail and we'll be moving those to the atomic check as well in
future patches.

v2:
 - Skip DDB calculations in the rare case where our transaction doesn't
   actually touch any CRTC's at all.  Assuming at least one CRTC state
   is present in our transaction, then it means we can't race with any
   transactions that would update dev_priv->active_crtcs (which requires
   _all_ CRTC locks).

v3:
 - Also calculate DDB during initial hw readout, to prevent using
   incorrect bios values. (Maarten)

v4:
 - Use new distrust_bios_wm flag instead of skip_initial_wm (which was
   never actually set).
 - Set intel_state->active_pipe_changes instead of just realloc_pipes

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude Paul <cpaul@redhat.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-10-git-send-email-matthew.d.roper@intel.com

drm/i915: Add distrust_bios_wm flag to dev_priv (v2)

SKL-style platforms can't fully trust the watermark/DDB settings
programmed by the BIOS and need to do extra sanitization on their first
atomic update.  Add a flag to dev_priv that is set during hardware
readout and cleared at the end of the first commit.

Note that for the somewhat common case where everything is turned off
when the driver starts up, we don't need to bother with a recompute...we
know exactly what the DDB should be (all zero's) so just setup the DDB
directly in that case.

v2:
 - Move clearing of distrust_bios_wm up below the swap_state call since
   it's a more natural / self-explanatory location.  (Maarten)
 - Use dev_priv->active_crtcs to test whether any CRTC's are turned on
   during HW WM readout rather than trying to count the active CRTC's
   again ourselves.  (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-9-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Allow skl_allocate_pipe_ddb() to operate on in-flight state (v3)

We eventually want to calculate watermark values at atomic 'check' time
instead of atomic 'commit' time so that any requested configurations
that result in impossible watermark requirements are properly rejected.
The first step along this path is to allocate the DDB at atomic 'check'
time.  As we perform this transition, allow the main allocation function
to operate successfully on either an in-flight state or an
already-commited state.  Once we complete the transition in a future
patch, we'll come back and remove the unnecessary logic for the
already-committed case.

v2: Rebase/refactor; we should no longer need to grab extra plane states
    while allocating the DDB since we can pull cached data rates and
    minimum block counts from the CRTC state for any planes that aren't
    being modified by this transaction.

v3:
 - Simplify memsets to clear DDB plane entries.  (Maarten)
 - Drop a redundant memset of plane[pipe][PLANE_CURSOR] that was added
   by an earlier Coccinelle patch.  (Maarten)
 - Assign *num_active at the top of skl_ddb_get_pipe_allocation_limits()
   so that no code paths return without setting it.  (kbuild robot)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-8-git-send-email-matthew.d.roper@intel.com

drm/i915: Track whether an atomic transaction changes the active CRTC's

For the purposes of DDB re-allocation we need to know whether a
transaction changes the list of CRTC's that are active.  While
state->modeset could be used for this purpose, that would be slightly
too aggressive since it would lead us to re-allocate the DDB when a
CRTC's mode changes, but not its final active state.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-7-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Store plane minimum blocks in CRTC wm state (v2)

This will eventually allow us to re-use old values without
re-calculating them for unchanged planes (which also helps us avoid
re-grabbing extra plane states).

v2:
 -  Drop unnecessary memset's; they were meant for a later patch (which
    got reworked anyway to not need them, but were mis-rebased into this
    one.  (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-6-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Allow calculation of data rate for in-flight state (v2)

Our skl_get_total_relative_data_rate() function gets passed a crtc state
object to calculate the data rate for, but it currently always looks
up the committed plane states that correspond to that CRTC.  Let's
check whether the CRTC state is an in-flight state (meaning
cstate->state is non-NULL) and if so, use the corresponding in-flight
plane states.

We'll soon be using this function exclusively for in-flight states; at
that time we'll be able to simplify the function a bit, but for now we
allow it to be used in either mode.

v2:
 - Rebase on top of changes to cache plane data rates.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-5-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Cache plane data rates in CRTC state

This will be important when we start calculating CRTC data rates for
in-flight CRTC states since it will allow us to calculate the total data
rate without needing to grab the plane state for any planes that aren't
updated by the transaction.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-4-git-send-email-matthew.d.roper@intel.com

drm/i915: Rename s/skl_compute_pipe_wm/skl_build_pipe_wm/

When we added atomic watermarks, we added a new display vfunc
'compute_pipe_wm' that is used to compute any pipe-specific watermark
information that we can at atomic check time.  This was a somewhat poor
naming choice since we already had a 'skl_compute_pipe_wm' function that
doesn't quite fit this model --- the existing SKL function is something
that gets used at atomic commit time, after the DDB allocation has been
determined.  Let's rename the existing SKL function to avoid confusion.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-3-git-send-email-matthew.d.roper@intel.com

drm/i915: Reorganize WM structs/unions in CRTC state

Reorganize the nested structures and unions we have for pipe watermark
data in intel_crtc_state so that platform-specific data can be added in
a more sensible manner (and save a bit of memory at the same time).

The change basically changes the organization from:

        union {
                struct intel_pipe_wm ilk;
                struct intel_pipe_wm skl;
        } optimal;

        struct intel_pipe_wm intermediate /* ILK-only */

to

        union {
                struct {
                        struct intel_pipe_wm intermediate;
                        struct intel_pipe_wm optimal;
                } ilk;

                struct {
                        struct intel_pipe_wm optimal;
                } skl;
        }

There should be no functional change here, but it will allow us to add
more platform-specific fields going forward (and more easily extend to
other platform types like VLV).

While we're at it, let's move the entire watermark substructure out to
its own structure definition to make the code slightly more readable.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-2-git-send-email-matthew.d.roper@intel.com

drm/i915: Remove redundant const from function return type

Marking function return types as const is redundant, as these are
rvalues and as such constant by definition. Code checkers and GCC will
warn about this so remove the modifier.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-5-git-send-email-imre.deak@intel.com

drm/i915: Handle error return from dma_set_coherent_mask()

A failure from these functions can lead to obscure bugs later, so it's
better not to suppress them and just fail module loading.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-4-git-send-email-imre.deak@intel.com

drm/i915: Add comments about fixed pipe->transcoder/PLL mapping

Code checkers may complain about the explicit casts between different
enum types, so add comments for known-valid cases to help future
triaging of such complaints.

v2:
- Make the comments more logical (Ville).

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-3-git-send-email-imre.deak@intel.com

drm/i915/gen9: Avoid using negative array index in skl_update_plane()

scaler_id may be negative as shown by conditions later in the function,
so don't use it as an array index in that case.

v2:
- Remove ps_ctrl while at it (Ville).

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-2-git-send-email-imre.deak@intel.com

drm/i915: Stop automatically retiring requests after a GPU hang

Following a GPU hang, we break out of the request loop in order to
unlock the struct_mutex for use by the GPU reset. However, if we retire
all the requests at that moment, we cannot identify the guilty request
after performing the reset.

v2: Not automatically retiring requests forces us to recheck for
available ringspace.

Fixes: f4457ae71fd6 ("drm/i915: Prevent leaking of -EIO from i915_wait_request()")
Testcase: igt/gem_reset_stats/ban-*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-4-git-send-email-chris@chris-wilson.co.uk

drm/i915: Stop retiring requests from busy/wait ioctls

In order to reduce the workload of the caller, we do not want to
actually have to retire requests of others when checking the busy status
of this object. This applies to both busy/wait ioctls as the wait ioctl
has a semantically equivalent mode to the busy ioctl.

At the present time, this is only a minor improvement to reduce the
workload of the busy ioctl under the struct_mutex which helps to reduce
its impact upon contention of struct_mutex. However, since it is mostly
a victim in highly contended scenarios, the impact is very minor until
we can eliminate the struct_mutex requirement for busy-ioctl in the near
future.

v2: Mention the patches intended limited impact. It is just paving the
way for greater changes whilst reducing the impact of a bugfix in the
next patch.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-3-git-send-email-chris@chris-wilson.co.uk