ics932s401: new clock generator chip driver
authorDarrick J. Wong <djwong@us.ibm.com>
Wed, 12 Nov 2008 21:27:04 +0000 (13:27 -0800)
committerLinus Torvalds <torvalds@linux-foundation.org>
Thu, 13 Nov 2008 01:17:18 +0000 (17:17 -0800)
The ics932s401 is a clock generator chip.  This driver allows users to
read the current clock outputs.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/ics932s401 [new file with mode: 0644]
drivers/misc/Kconfig
drivers/misc/Makefile
drivers/misc/ics932s401.c [new file with mode: 0644]

diff --git a/Documentation/ics932s401 b/Documentation/ics932s401
new file mode 100644 (file)
index 0000000..07a739f
--- /dev/null
@@ -0,0 +1,31 @@
+Kernel driver ics932s401
+======================
+
+Supported chips:
+  * IDT ICS932S401
+    Prefix: 'ics932s401'
+    Addresses scanned: I2C 0x69
+    Datasheet: Publically available at the IDT website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the IDT ICS932S401 chip family.
+
+This chip has 4 clock outputs--a base clock for the CPU (which is likely
+multiplied to get the real CPU clock), a system clock, a PCI clock, a USB
+clock, and a reference clock.  The driver reports selected and actual
+frequency.  If spread spectrum mode is enabled, the driver also reports by what
+percent the clock signal is being spread, which should be between 0 and -0.5%.
+All frequencies are reported in KHz.
+
+The ICS932S401 monitors all inputs continuously. The driver will not read
+the registers more often than once every other second.
+
+Special Features
+----------------
+
+The clocks could be reprogrammed to increase system speed.  I will not help you
+do this, as you risk damaging your system!
index 4494ad27cbf135b0156032d7224b989fe02b0723..dcac7ca76937dcfd14bd5f60f1d0d8e82a4c6ad4 100644 (file)
@@ -227,6 +227,16 @@ config HP_WMI
          To compile this driver as a module, choose M here: the module will
          be called hp-wmi.
 
+config ICS932S401
+       tristate "Integrated Circuits ICS932S401"
+       depends on I2C && EXPERIMENTAL
+       help
+         If you say yes here you get support for the Integrated Circuits
+         ICS932S401 clock control chips.
+
+         This driver can also be built as a module. If so, the module
+         will be called ics932s401.
+
 config MSI_LAPTOP
         tristate "MSI Laptop Extras"
         depends on X86
index 909e2468cdc974be5e4ffc7c3e85affc6f6129c6..bb14633d13628d8ec89a8d5fda60426cf50eed30 100644 (file)
@@ -14,6 +14,7 @@ obj-$(CONFIG_ATMEL_PWM)               += atmel_pwm.o
 obj-$(CONFIG_ATMEL_SSC)                += atmel-ssc.o
 obj-$(CONFIG_ATMEL_TCLIB)      += atmel_tclib.o
 obj-$(CONFIG_HP_WMI)           += hp-wmi.o
+obj-$(CONFIG_ICS932S401)       += ics932s401.o
 obj-$(CONFIG_TC1100_WMI)       += tc1100-wmi.o
 obj-$(CONFIG_LKDTM)            += lkdtm.o
 obj-$(CONFIG_TIFM_CORE)        += tifm_core.o
diff --git a/drivers/misc/ics932s401.c b/drivers/misc/ics932s401.c
new file mode 100644 (file)
index 0000000..6e43ab4
--- /dev/null
@@ -0,0 +1,515 @@
+/*
+ * A driver for the Integrated Circuits ICS932S401
+ * Copyright (C) 2008 IBM
+ *
+ * Author: Darrick J. Wong <djwong@us.ibm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+#include <linux/log2.h>
+
+/* Addresses to scan */
+static const unsigned short normal_i2c[] = { 0x69, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(ics932s401);
+
+/* ICS932S401 registers */
+#define ICS932S401_REG_CFG2                    0x01
+#define        ICS932S401_CFG1_SPREAD          0x01
+#define ICS932S401_REG_CFG7                    0x06
+#define                ICS932S401_FS_MASK              0x07
+#define        ICS932S401_REG_VENDOR_REV               0x07
+#define                ICS932S401_VENDOR               1
+#define                ICS932S401_VENDOR_MASK          0x0F
+#define                ICS932S401_REV                  4
+#define                ICS932S401_REV_SHIFT            4
+#define ICS932S401_REG_DEVICE                  0x09
+#define                ICS932S401_DEVICE               11
+#define        ICS932S401_REG_CTRL                     0x0A
+#define                ICS932S401_MN_ENABLED           0x80
+#define                ICS932S401_CPU_ALT              0x04
+#define                ICS932S401_SRC_ALT              0x08
+#define ICS932S401_REG_CPU_M_CTRL              0x0B
+#define                ICS932S401_M_MASK               0x3F
+#define        ICS932S401_REG_CPU_N_CTRL               0x0C
+#define        ICS932S401_REG_CPU_SPREAD1              0x0D
+#define ICS932S401_REG_CPU_SPREAD2             0x0E
+#define                ICS932S401_SPREAD_MASK          0x7FFF
+#define ICS932S401_REG_SRC_M_CTRL              0x0F
+#define ICS932S401_REG_SRC_N_CTRL              0x10
+#define        ICS932S401_REG_SRC_SPREAD1              0x11
+#define ICS932S401_REG_SRC_SPREAD2             0x12
+#define ICS932S401_REG_CPU_DIVISOR             0x13
+#define        ICS932S401_CPU_DIVISOR_SHIFT    4
+#define ICS932S401_REG_PCISRC_DIVISOR          0x14
+#define                ICS932S401_SRC_DIVISOR_MASK     0x0F
+#define                ICS932S401_PCI_DIVISOR_SHIFT    4
+
+/* Base clock is 14.318MHz */
+#define BASE_CLOCK                             14318
+
+#define NUM_REGS                               21
+#define NUM_MIRRORED_REGS                      15
+
+static int regs_to_copy[NUM_MIRRORED_REGS] = {
+       ICS932S401_REG_CFG2,
+       ICS932S401_REG_CFG7,
+       ICS932S401_REG_VENDOR_REV,
+       ICS932S401_REG_DEVICE,
+       ICS932S401_REG_CTRL,
+       ICS932S401_REG_CPU_M_CTRL,
+       ICS932S401_REG_CPU_N_CTRL,
+       ICS932S401_REG_CPU_SPREAD1,
+       ICS932S401_REG_CPU_SPREAD2,
+       ICS932S401_REG_SRC_M_CTRL,
+       ICS932S401_REG_SRC_N_CTRL,
+       ICS932S401_REG_SRC_SPREAD1,
+       ICS932S401_REG_SRC_SPREAD2,
+       ICS932S401_REG_CPU_DIVISOR,
+       ICS932S401_REG_PCISRC_DIVISOR,
+};
+
+/* How often do we reread sensors values? (In jiffies) */
+#define SENSOR_REFRESH_INTERVAL        (2 * HZ)
+
+/* How often do we reread sensor limit values? (In jiffies) */
+#define LIMIT_REFRESH_INTERVAL (60 * HZ)
+
+struct ics932s401_data {
+       struct attribute_group  attrs;
+       struct mutex            lock;
+       char                    sensors_valid;
+       unsigned long           sensors_last_updated;   /* In jiffies */
+
+       u8                      regs[NUM_REGS];
+};
+
+static int ics932s401_probe(struct i2c_client *client,
+                        const struct i2c_device_id *id);
+static int ics932s401_detect(struct i2c_client *client, int kind,
+                         struct i2c_board_info *info);
+static int ics932s401_remove(struct i2c_client *client);
+
+static const struct i2c_device_id ics932s401_id[] = {
+       { "ics932s401", ics932s401 },
+       { }
+};
+MODULE_DEVICE_TABLE(i2c, ics932s401_id);
+
+static struct i2c_driver ics932s401_driver = {
+       .class          = I2C_CLASS_HWMON,
+       .driver = {
+               .name   = "ics932s401",
+       },
+       .probe          = ics932s401_probe,
+       .remove         = ics932s401_remove,
+       .id_table       = ics932s401_id,
+       .detect         = ics932s401_detect,
+       .address_data   = &addr_data,
+};
+
+static struct ics932s401_data *ics932s401_update_device(struct device *dev)
+{
+       struct i2c_client *client = to_i2c_client(dev);
+       struct ics932s401_data *data = i2c_get_clientdata(client);
+       unsigned long local_jiffies = jiffies;
+       int i, temp;
+
+       mutex_lock(&data->lock);
+       if (time_before(local_jiffies, data->sensors_last_updated +
+               SENSOR_REFRESH_INTERVAL)
+               && data->sensors_valid)
+               goto out;
+
+       /*
+        * Each register must be read as a word and then right shifted 8 bits.
+        * Not really sure why this is; setting the "byte count programming"
+        * register to 1 does not fix this problem.
+        */
+       for (i = 0; i < NUM_MIRRORED_REGS; i++) {
+               temp = i2c_smbus_read_word_data(client, regs_to_copy[i]);
+               data->regs[regs_to_copy[i]] = temp >> 8;
+       }
+
+       data->sensors_last_updated = local_jiffies;
+       data->sensors_valid = 1;
+
+out:
+       mutex_unlock(&data->lock);
+       return data;
+}
+
+static ssize_t show_spread_enabled(struct device *dev,
+                                  struct device_attribute *devattr,
+                                  char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+
+       if (data->regs[ICS932S401_REG_CFG2] & ICS932S401_CFG1_SPREAD)
+               return sprintf(buf, "1\n");
+
+       return sprintf(buf, "0\n");
+}
+
+/* bit to cpu khz map */
+static const int fs_speeds[] = {
+       266666,
+       133333,
+       200000,
+       166666,
+       333333,
+       100000,
+       400000,
+       0,
+};
+
+/* clock divisor map */
+static const int divisors[] = {2, 3, 5, 15, 4, 6, 10, 30, 8, 12, 20, 60, 16,
+                              24, 40, 120};
+
+/* Calculate CPU frequency from the M/N registers. */
+static int calculate_cpu_freq(struct ics932s401_data *data)
+{
+       int m, n, freq;
+
+       m = data->regs[ICS932S401_REG_CPU_M_CTRL] & ICS932S401_M_MASK;
+       n = data->regs[ICS932S401_REG_CPU_N_CTRL];
+
+       /* Pull in bits 8 & 9 from the M register */
+       n |= ((int)data->regs[ICS932S401_REG_CPU_M_CTRL] & 0x80) << 1;
+       n |= ((int)data->regs[ICS932S401_REG_CPU_M_CTRL] & 0x40) << 3;
+
+       freq = BASE_CLOCK * (n + 8) / (m + 2);
+       freq /= divisors[data->regs[ICS932S401_REG_CPU_DIVISOR] >>
+                        ICS932S401_CPU_DIVISOR_SHIFT];
+
+       return freq;
+}
+
+static ssize_t show_cpu_clock(struct device *dev,
+                             struct device_attribute *devattr,
+                             char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+
+       return sprintf(buf, "%d\n", calculate_cpu_freq(data));
+}
+
+static ssize_t show_cpu_clock_sel(struct device *dev,
+                                 struct device_attribute *devattr,
+                                 char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+       int freq;
+
+       if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_MN_ENABLED)
+               freq = calculate_cpu_freq(data);
+       else {
+               /* Freq is neatly wrapped up for us */
+               int fid = data->regs[ICS932S401_REG_CFG7] & ICS932S401_FS_MASK;
+               freq = fs_speeds[fid];
+               if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_CPU_ALT) {
+                       switch (freq) {
+                       case 166666:
+                               freq = 160000;
+                               break;
+                       case 333333:
+                               freq = 320000;
+                               break;
+                       }
+               }
+       }
+
+       return sprintf(buf, "%d\n", freq);
+}
+
+/* Calculate SRC frequency from the M/N registers. */
+static int calculate_src_freq(struct ics932s401_data *data)
+{
+       int m, n, freq;
+
+       m = data->regs[ICS932S401_REG_SRC_M_CTRL] & ICS932S401_M_MASK;
+       n = data->regs[ICS932S401_REG_SRC_N_CTRL];
+
+       /* Pull in bits 8 & 9 from the M register */
+       n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x80) << 1;
+       n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x40) << 3;
+
+       freq = BASE_CLOCK * (n + 8) / (m + 2);
+       freq /= divisors[data->regs[ICS932S401_REG_PCISRC_DIVISOR] &
+                        ICS932S401_SRC_DIVISOR_MASK];
+
+       return freq;
+}
+
+static ssize_t show_src_clock(struct device *dev,
+                             struct device_attribute *devattr,
+                             char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+
+       return sprintf(buf, "%d\n", calculate_src_freq(data));
+}
+
+static ssize_t show_src_clock_sel(struct device *dev,
+                                 struct device_attribute *devattr,
+                                 char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+       int freq;
+
+       if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_MN_ENABLED)
+               freq = calculate_src_freq(data);
+       else
+               /* Freq is neatly wrapped up for us */
+               if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_CPU_ALT &&
+                   data->regs[ICS932S401_REG_CTRL] & ICS932S401_SRC_ALT)
+                       freq = 96000;
+               else
+                       freq = 100000;
+
+       return sprintf(buf, "%d\n", freq);
+}
+
+/* Calculate PCI frequency from the SRC M/N registers. */
+static int calculate_pci_freq(struct ics932s401_data *data)
+{
+       int m, n, freq;
+
+       m = data->regs[ICS932S401_REG_SRC_M_CTRL] & ICS932S401_M_MASK;
+       n = data->regs[ICS932S401_REG_SRC_N_CTRL];
+
+       /* Pull in bits 8 & 9 from the M register */
+       n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x80) << 1;
+       n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x40) << 3;
+
+       freq = BASE_CLOCK * (n + 8) / (m + 2);
+       freq /= divisors[data->regs[ICS932S401_REG_PCISRC_DIVISOR] >>
+                        ICS932S401_PCI_DIVISOR_SHIFT];
+
+       return freq;
+}
+
+static ssize_t show_pci_clock(struct device *dev,
+                             struct device_attribute *devattr,
+                             char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+
+       return sprintf(buf, "%d\n", calculate_pci_freq(data));
+}
+
+static ssize_t show_pci_clock_sel(struct device *dev,
+                                 struct device_attribute *devattr,
+                                 char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+       int freq;
+
+       if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_MN_ENABLED)
+               freq = calculate_pci_freq(data);
+       else
+               freq = 33333;
+
+       return sprintf(buf, "%d\n", freq);
+}
+
+static ssize_t show_value(struct device *dev,
+                         struct device_attribute *devattr,
+                         char *buf);
+
+static ssize_t show_spread(struct device *dev,
+                          struct device_attribute *devattr,
+                          char *buf);
+
+static DEVICE_ATTR(spread_enabled, S_IRUGO, show_spread_enabled, NULL);
+static DEVICE_ATTR(cpu_clock_selection, S_IRUGO, show_cpu_clock_sel, NULL);
+static DEVICE_ATTR(cpu_clock, S_IRUGO, show_cpu_clock, NULL);
+static DEVICE_ATTR(src_clock_selection, S_IRUGO, show_src_clock_sel, NULL);
+static DEVICE_ATTR(src_clock, S_IRUGO, show_src_clock, NULL);
+static DEVICE_ATTR(pci_clock_selection, S_IRUGO, show_pci_clock_sel, NULL);
+static DEVICE_ATTR(pci_clock, S_IRUGO, show_pci_clock, NULL);
+static DEVICE_ATTR(usb_clock, S_IRUGO, show_value, NULL);
+static DEVICE_ATTR(ref_clock, S_IRUGO, show_value, NULL);
+static DEVICE_ATTR(cpu_spread, S_IRUGO, show_spread, NULL);
+static DEVICE_ATTR(src_spread, S_IRUGO, show_spread, NULL);
+
+static struct attribute *ics932s401_attr[] =
+{
+       &dev_attr_spread_enabled.attr,
+       &dev_attr_cpu_clock_selection.attr,
+       &dev_attr_cpu_clock.attr,
+       &dev_attr_src_clock_selection.attr,
+       &dev_attr_src_clock.attr,
+       &dev_attr_pci_clock_selection.attr,
+       &dev_attr_pci_clock.attr,
+       &dev_attr_usb_clock.attr,
+       &dev_attr_ref_clock.attr,
+       &dev_attr_cpu_spread.attr,
+       &dev_attr_src_spread.attr,
+       NULL
+};
+
+static ssize_t show_value(struct device *dev,
+                         struct device_attribute *devattr,
+                         char *buf)
+{
+       int x;
+
+       if (devattr == &dev_attr_usb_clock)
+               x = 48000;
+       else if (devattr == &dev_attr_ref_clock)
+               x = BASE_CLOCK;
+       else
+               BUG();
+
+       return sprintf(buf, "%d\n", x);
+}
+
+static ssize_t show_spread(struct device *dev,
+                          struct device_attribute *devattr,
+                          char *buf)
+{
+       struct ics932s401_data *data = ics932s401_update_device(dev);
+       int reg;
+       unsigned long val;
+
+       if (!(data->regs[ICS932S401_REG_CFG2] & ICS932S401_CFG1_SPREAD))
+               return sprintf(buf, "0%%\n");
+
+       if (devattr == &dev_attr_src_spread)
+               reg = ICS932S401_REG_SRC_SPREAD1;
+       else if (devattr == &dev_attr_cpu_spread)
+               reg = ICS932S401_REG_CPU_SPREAD1;
+       else
+               BUG();
+
+       val = data->regs[reg] | (data->regs[reg + 1] << 8);
+       val &= ICS932S401_SPREAD_MASK;
+
+       /* Scale 0..2^14 to -0.5. */
+       val = 500000 * val / 16384;
+       return sprintf(buf, "-0.%lu%%\n", val);
+}
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int ics932s401_detect(struct i2c_client *client, int kind,
+                         struct i2c_board_info *info)
+{
+       struct i2c_adapter *adapter = client->adapter;
+
+       if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+               return -ENODEV;
+
+       if (kind <= 0) {
+               int vendor, device, revision;
+
+               vendor = i2c_smbus_read_word_data(client,
+                                                 ICS932S401_REG_VENDOR_REV);
+               vendor >>= 8;
+               revision = vendor >> ICS932S401_REV_SHIFT;
+               vendor &= ICS932S401_VENDOR_MASK;
+               if (vendor != ICS932S401_VENDOR)
+                       return -ENODEV;
+
+               device = i2c_smbus_read_word_data(client,
+                                                 ICS932S401_REG_DEVICE);
+               device >>= 8;
+               if (device != ICS932S401_DEVICE)
+                       return -ENODEV;
+
+               if (revision != ICS932S401_REV)
+                       dev_info(&adapter->dev, "Unknown revision %d\n",
+                                revision);
+       } else
+               dev_dbg(&adapter->dev, "detection forced\n");
+
+       strlcpy(info->type, "ics932s401", I2C_NAME_SIZE);
+
+       return 0;
+}
+
+static int ics932s401_probe(struct i2c_client *client,
+                        const struct i2c_device_id *id)
+{
+       struct ics932s401_data *data;
+       int err;
+
+       data = kzalloc(sizeof(struct ics932s401_data), GFP_KERNEL);
+       if (!data) {
+               err = -ENOMEM;
+               goto exit;
+       }
+
+       i2c_set_clientdata(client, data);
+       mutex_init(&data->lock);
+
+       dev_info(&client->dev, "%s chip found\n", client->name);
+
+       /* Register sysfs hooks */
+       data->attrs.attrs = ics932s401_attr;
+       err = sysfs_create_group(&client->dev.kobj, &data->attrs);
+       if (err)
+               goto exit_free;
+
+       return 0;
+
+exit_free:
+       kfree(data);
+exit:
+       return err;
+}
+
+static int ics932s401_remove(struct i2c_client *client)
+{
+       struct ics932s401_data *data = i2c_get_clientdata(client);
+
+       sysfs_remove_group(&client->dev.kobj, &data->attrs);
+       kfree(data);
+       return 0;
+}
+
+static int __init ics932s401_init(void)
+{
+       return i2c_add_driver(&ics932s401_driver);
+}
+
+static void __exit ics932s401_exit(void)
+{
+       i2c_del_driver(&ics932s401_driver);
+}
+
+MODULE_AUTHOR("Darrick J. Wong <djwong@us.ibm.com>");
+MODULE_DESCRIPTION("ICS932S401 driver");
+MODULE_LICENSE("GPL");
+
+module_init(ics932s401_init);
+module_exit(ics932s401_exit);
+
+/* IBM IntelliStation Z30 */
+MODULE_ALIAS("dmi:bvnIBM:*:rn9228:*");
+MODULE_ALIAS("dmi:bvnIBM:*:rn9232:*");
+
+/* IBM x3650/x3550 */
+MODULE_ALIAS("dmi:bvnIBM:*:pnIBMSystemx3650*");
+MODULE_ALIAS("dmi:bvnIBM:*:pnIBMSystemx3550*");