USB: CP210X Use official request code definitions
authorCraig Shelley <craig@microtron.org.uk>
Thu, 11 Jun 2009 12:53:30 +0000 (13:53 +0100)
committerLinus Torvalds <torvalds@linux-foundation.org>
Thu, 11 Jun 2009 15:51:05 +0000 (08:51 -0700)
The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.

Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/usb/serial/cp210x.c

index ac4944a8152155af8277f8c43bea7eb5e37fdba9..b50f27fa11d0a7bb7f4e42d9027184e8a19c49bf 100644 (file)
@@ -27,7 +27,7 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v0.08"
+#define DRIVER_VERSION "v0.09"
 #define DRIVER_DESC "Silicon Labs CP2101/CP2102 RS232 serial adaptor driver"
 
 /*
@@ -144,23 +144,40 @@ static struct usb_serial_driver cp2101_device = {
 #define REQTYPE_HOST_TO_DEVICE 0x41
 #define REQTYPE_DEVICE_TO_HOST 0xc1
 
-/* Config SET requests. To GET, add 1 to the request number */
-#define CP2101_UART            0x00    /* Enable / Disable */
-#define CP2101_BAUDRATE                0x01    /* (BAUD_RATE_GEN_FREQ / baudrate) */
-#define CP2101_BITS            0x03    /* 0x(0)(databits)(parity)(stopbits) */
-#define CP2101_BREAK           0x05    /* On / Off */
-#define CP2101_CONTROL         0x07    /* Flow control line states */
-#define CP2101_MODEMCTL                0x13    /* Modem controls */
-#define CP2101_CONFIG_6                0x19    /* 6 bytes of config data ??? */
-
-/* CP2101_UART */
+/* Config request codes */
+#define CP210X_IFC_ENABLE      0x00
+#define CP210X_SET_BAUDDIV     0x01
+#define CP210X_GET_BAUDDIV     0x02
+#define CP210X_SET_LINE_CTL    0x03
+#define CP210X_GET_LINE_CTL    0x04
+#define CP210X_SET_BREAK       0x05
+#define CP210X_IMM_CHAR                0x06
+#define CP210X_SET_MHS         0x07
+#define CP210X_GET_MDMSTS      0x08
+#define CP210X_SET_XON         0x09
+#define CP210X_SET_XOFF                0x0A
+#define CP210X_SET_EVENTMASK   0x0B
+#define CP210X_GET_EVENTMASK   0x0C
+#define CP210X_SET_CHAR                0x0D
+#define CP210X_GET_CHARS       0x0E
+#define CP210X_GET_PROPS       0x0F
+#define CP210X_GET_COMM_STATUS 0x10
+#define CP210X_RESET           0x11
+#define CP210X_PURGE           0x12
+#define CP210X_SET_FLOW                0x13
+#define CP210X_GET_FLOW                0x14
+#define CP210X_EMBED_EVENTS    0x15
+#define CP210X_GET_EVENTSTATE  0x16
+#define CP210X_SET_CHARS       0x19
+
+/* CP210X_IFC_ENABLE */
 #define UART_ENABLE            0x0001
 #define UART_DISABLE           0x0000
 
-/* CP2101_BAUDRATE */
+/* CP210X_(SET|GET)_BAUDDIV */
 #define BAUD_RATE_GEN_FREQ     0x384000
 
-/* CP2101_BITS */
+/* CP210X_(SET|GET)_LINE_CTL */
 #define BITS_DATA_MASK         0X0f00
 #define BITS_DATA_5            0X0500
 #define BITS_DATA_6            0X0600
@@ -180,11 +197,11 @@ static struct usb_serial_driver cp2101_device = {
 #define BITS_STOP_1_5          0x0001
 #define BITS_STOP_2            0x0002
 
-/* CP2101_BREAK */
+/* CP210X_SET_BREAK */
 #define BREAK_ON               0x0000
 #define BREAK_OFF              0x0001
 
-/* CP2101_CONTROL */
+/* CP210X_(SET_MHS|GET_MDMSTS) */
 #define CONTROL_DTR            0x0001
 #define CONTROL_RTS            0x0002
 #define CONTROL_CTS            0x0010
@@ -217,9 +234,6 @@ static int cp2101_get_config(struct usb_serial_port *port, u8 request,
                return -ENOMEM;
        }
 
-       /* For get requests, the request number must be incremented */
-       request++;
-
        /* Issue the request, attempting to read 'size' bytes */
        result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
                                request, REQTYPE_DEVICE_TO_HOST, 0x0000,
@@ -357,7 +371,7 @@ static int cp2101_open(struct tty_struct *tty, struct usb_serial_port *port,
 
        dbg("%s - port %d", __func__, port->number);
 
-       if (cp2101_set_config_single(port, CP2101_UART, UART_ENABLE)) {
+       if (cp2101_set_config_single(port, CP210X_IFC_ENABLE, UART_ENABLE)) {
                dev_err(&port->dev, "%s - Unable to enable UART\n",
                                __func__);
                return -EPROTO;
@@ -415,7 +429,7 @@ static void cp2101_close(struct usb_serial_port *port)
 
        mutex_lock(&port->serial->disc_mutex);
        if (!port->serial->disconnected)
-               cp2101_set_config_single(port, CP2101_UART, UART_DISABLE);
+               cp2101_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE);
        mutex_unlock(&port->serial->disc_mutex);
 }
 
@@ -456,7 +470,7 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
 
        dbg("%s - port %d", __func__, port->number);
 
-       cp2101_get_config(port, CP2101_BAUDRATE, &baud, 2);
+       cp2101_get_config(port, CP210X_GET_BAUDDIV, &baud, 2);
        /* Convert to baudrate */
        if (baud)
                baud = cp2101_quantise_baudrate((BAUD_RATE_GEN_FREQ + baud/2)/ baud);
@@ -466,7 +480,7 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
 
        cflag = *cflagp;
 
-       cp2101_get_config(port, CP2101_BITS, &bits, 2);
+       cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
        cflag &= ~CSIZE;
        switch (bits & BITS_DATA_MASK) {
        case BITS_DATA_5:
@@ -491,14 +505,14 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
                cflag |= CS8;
                bits &= ~BITS_DATA_MASK;
                bits |= BITS_DATA_8;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        default:
                dbg("%s - Unknown number of data bits, using 8", __func__);
                cflag |= CS8;
                bits &= ~BITS_DATA_MASK;
                bits |= BITS_DATA_8;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        }
 
@@ -521,20 +535,20 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
                                __func__);
                cflag &= ~PARENB;
                bits &= ~BITS_PARITY_MASK;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        case BITS_PARITY_SPACE:
                dbg("%s - parity = SPACE (not supported, disabling parity)",
                                __func__);
                cflag &= ~PARENB;
                bits &= ~BITS_PARITY_MASK;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        default:
                dbg("%s - Unknown parity mode, disabling parity", __func__);
                cflag &= ~PARENB;
                bits &= ~BITS_PARITY_MASK;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        }
 
@@ -547,7 +561,7 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
                dbg("%s - stop bits = 1.5 (not supported, using 1 stop bit)",
                                                                __func__);
                bits &= ~BITS_STOP_MASK;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        case BITS_STOP_2:
                dbg("%s - stop bits = 2", __func__);
@@ -557,11 +571,11 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
                dbg("%s - Unknown number of stop bits, using 1 stop bit",
                                                                __func__);
                bits &= ~BITS_STOP_MASK;
-               cp2101_set_config(port, CP2101_BITS, &bits, 2);
+               cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
                break;
        }
 
-       cp2101_get_config(port, CP2101_MODEMCTL, modem_ctl, 16);
+       cp2101_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
        if (modem_ctl[0] & 0x0008) {
                dbg("%s - flow control = CRTSCTS", __func__);
                cflag |= CRTSCTS;
@@ -594,7 +608,7 @@ static void cp2101_set_termios(struct tty_struct *tty,
        if (baud != tty_termios_baud_rate(old_termios) && baud != 0) {
                dbg("%s - Setting baud rate to %d baud", __func__,
                                baud);
-               if (cp2101_set_config_single(port, CP2101_BAUDRATE,
+               if (cp2101_set_config_single(port, CP210X_SET_BAUDDIV,
                                        ((BAUD_RATE_GEN_FREQ + baud/2) / baud))) {
                        dbg("Baud rate requested not supported by device\n");
                        baud = tty_termios_baud_rate(old_termios);
@@ -605,7 +619,7 @@ static void cp2101_set_termios(struct tty_struct *tty,
 
        /* If the number of data bits is to be updated */
        if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
-               cp2101_get_config(port, CP2101_BITS, &bits, 2);
+               cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
                bits &= ~BITS_DATA_MASK;
                switch (cflag & CSIZE) {
                case CS5:
@@ -635,13 +649,13 @@ static void cp2101_set_termios(struct tty_struct *tty,
                                bits |= BITS_DATA_8;
                                break;
                }
-               if (cp2101_set_config(port, CP2101_BITS, &bits, 2))
+               if (cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
                        dbg("Number of data bits requested "
                                        "not supported by device\n");
        }
 
        if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))) {
-               cp2101_get_config(port, CP2101_BITS, &bits, 2);
+               cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
                bits &= ~BITS_PARITY_MASK;
                if (cflag & PARENB) {
                        if (cflag & PARODD) {
@@ -652,13 +666,13 @@ static void cp2101_set_termios(struct tty_struct *tty,
                                dbg("%s - parity = EVEN", __func__);
                        }
                }
-               if (cp2101_set_config(port, CP2101_BITS, &bits, 2))
+               if (cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
                        dbg("Parity mode not supported "
                                        "by device\n");
        }
 
        if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
-               cp2101_get_config(port, CP2101_BITS, &bits, 2);
+               cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
                bits &= ~BITS_STOP_MASK;
                if (cflag & CSTOPB) {
                        bits |= BITS_STOP_2;
@@ -667,13 +681,13 @@ static void cp2101_set_termios(struct tty_struct *tty,
                        bits |= BITS_STOP_1;
                        dbg("%s - stop bits = 1", __func__);
                }
-               if (cp2101_set_config(port, CP2101_BITS, &bits, 2))
+               if (cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
                        dbg("Number of stop bits requested "
                                        "not supported by device\n");
        }
 
        if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
-               cp2101_get_config(port, CP2101_MODEMCTL, modem_ctl, 16);
+               cp2101_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
                dbg("%s - read modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
                                __func__, modem_ctl[0], modem_ctl[1],
                                modem_ctl[2], modem_ctl[3]);
@@ -693,7 +707,7 @@ static void cp2101_set_termios(struct tty_struct *tty,
                dbg("%s - write modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
                                __func__, modem_ctl[0], modem_ctl[1],
                                modem_ctl[2], modem_ctl[3]);
-               cp2101_set_config(port, CP2101_MODEMCTL, modem_ctl, 16);
+               cp2101_set_config(port, CP210X_SET_FLOW, modem_ctl, 16);
        }
 
 }
@@ -731,7 +745,7 @@ static int cp2101_tiocmset_port(struct usb_serial_port *port, struct file *file,
 
        dbg("%s - control = 0x%.4x", __func__, control);
 
-       return cp2101_set_config(port, CP2101_CONTROL, &control, 2);
+       return cp2101_set_config(port, CP210X_SET_MHS, &control, 2);
 }
 
 static int cp2101_tiocmget (struct tty_struct *tty, struct file *file)
@@ -742,7 +756,7 @@ static int cp2101_tiocmget (struct tty_struct *tty, struct file *file)
 
        dbg("%s - port %d", __func__, port->number);
 
-       cp2101_get_config(port, CP2101_CONTROL, &control, 1);
+       cp2101_get_config(port, CP210X_GET_MDMSTS, &control, 1);
 
        result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
                |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
@@ -768,7 +782,7 @@ static void cp2101_break_ctl (struct tty_struct *tty, int break_state)
                state = BREAK_ON;
        dbg("%s - turning break %s", __func__,
                        state == BREAK_OFF ? "off" : "on");
-       cp2101_set_config(port, CP2101_BREAK, &state, 2);
+       cp2101_set_config(port, CP210X_SET_BREAK, &state, 2);
 }
 
 static int cp2101_startup(struct usb_serial *serial)