atmel-mci: add MCI2 register definitions

New revision of Atmel MCI interface adds new features. This is a update of
register definition in header file. This new MCI IP is called MCI2.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>

diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h
index adfb885db60f1fed3176f126d867958b3d72fc09..fc8a0fe7c5c57b1fbf3282733b285c7da40aaf8f 100644 (file)
--- a/drivers/mmc/host/atmel-mci-regs.h
+++ b/drivers/mmc/host/atmel-mci-regs.h
@@ -10,6 +10,7 @@
 
 /*
  * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
  */
 
 #ifndef __DRIVERS_MMC_ATMEL_MCI_H__
@@ -39,6 +40,7 @@
 # define MCI_SDCSEL_MASK       (  3 <<  0)
 # define MCI_SDCBUS_1BIT       (  0 <<  6)     /* 1-bit data bus */
 # define MCI_SDCBUS_4BIT       (  2 <<  6)     /* 4-bit data bus */
+# define MCI_SDCBUS_8BIT       (  3 <<  6)     /* 8-bit data bus[2] */
 # define MCI_SDCBUS_MASK       (  3 <<  6)
 #define MCI_ARGR               0x0010  /* Command Argument */
 #define MCI_CMDR               0x0014  /* Command */
@@ -67,6 +69,9 @@
 #define MCI_BLKR               0x0018  /* Block */
 # define MCI_BCNT(x)           ((x) <<  0)     /* Data Block Count */
 # define MCI_BLKLEN(x)         ((x) << 16)     /* Data Block Length */
+#define MCI_CSTOR              0x001c  /* Completion Signal Timeout[2] */
+# define MCI_CSTOCYC(x)                ((x) <<  0)     /* CST cycles */
+# define MCI_CSTOMUL(x)                ((x) <<  4)     /* CST multiplier */
 #define MCI_RSPR               0x0020  /* Response 0 */
 #define MCI_RSPR1              0x0024  /* Response 1 */
 #define MCI_RSPR2              0x0028  /* Response 2 */
@@ -94,7 +99,24 @@
 # define MCI_DTOE              (  1 <<  22)    /* Data Time-Out Error */
 # define MCI_OVRE              (  1 <<  30)    /* RX Overrun Error */
 # define MCI_UNRE              (  1 <<  31)    /* TX Underrun Error */
+#define MCI_DMA                        0x0050  /* DMA Configuration[2] */
+# define MCI_DMA_OFFSET(x)     ((x) <<  0)     /* DMA Write Buffer Offset */
+# define MCI_DMA_CHKSIZE(x)    ((x) <<  4)     /* DMA Channel Read and Write Chunk Size */
+# define MCI_DMAEN             (  1 <<  8)     /* DMA Hardware Handshaking Enable */
+#define MCI_CFG                        0x0054  /* Configuration[2] */
+# define MCI_CFG_FIFOMODE_1DATA        (  1 <<  0)     /* MCI Internal FIFO control mode */
+# define MCI_CFG_FERRCTRL_COR  (  1 <<  4)     /* Flow Error flag reset control mode */
+# define MCI_CFG_HSMODE                (  1 <<  8)     /* High Speed Mode */
+# define MCI_CFG_LSYNC         (  1 << 12)     /* Synchronize on the last block */
+#define MCI_WPMR               0x00e4  /* Write Protection Mode[2] */
+# define MCI_WP_EN             (  1 <<  0)     /* WP Enable */
+# define MCI_WP_KEY            (0x4d4349 << 8) /* WP Key */
+#define MCI_WPSR               0x00e8  /* Write Protection Status[2] */
+# define MCI_GET_WP_VS(x)      ((x) & 0x0f)
+# define MCI_GET_WP_VSRC(x)    (((x) >> 8) & 0xffff)
+#define MCI_FIFO_APERTURE      0x0200  /* FIFO Aperture[2] */
 
+/* This is not including the FIFO Aperture on MCI2 */
 #define MCI_REGS_SIZE          0x100
 
 /* Register access macros */