drivers/staging/slicoss/slicoss.c

   1 /**************************************************************************
   2  *
   3  * Copyright  2000-2006 Alacritech, Inc.  All rights reserved.
   4  *
   5  * Redistribution and use in source and binary forms, with or without
   6  * modification, are permitted provided that the following conditions
   7  * are met:
   8  *
   9  * 1. Redistributions of source code must retain the above copyright
  10  *    notice, this list of conditions and the following disclaimer.
  11  * 2. Redistributions in binary form must reproduce the above
  12  *    copyright notice, this list of conditions and the following
  13  *    disclaimer in the documentation and/or other materials provided
  14  *    with the distribution.
  15  *
  16  * Alternatively, this software may be distributed under the terms of the
  17  * GNU General Public License ("GPL") version 2 as published by the Free
  18  * Software Foundation.
  19  *
  20  * THIS SOFTWARE IS PROVIDED BY ALACRITECH, INC. ``AS IS'' AND ANY
  21  * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  22  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
  23  * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL ALACRITECH, INC. OR
  24  * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
  25  * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
  26  * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
  27  * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  28  * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  29  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
  30  * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
  31  * SUCH DAMAGE.
  32  *
  33  * The views and conclusions contained in the software and documentation
  34  * are those of the authors and should not be interpreted as representing
  35  * official policies, either expressed or implied, of Alacritech, Inc.
  36  *
  37  **************************************************************************/
  38
  39 /*
  40  * FILENAME: slicoss.c
  41  *
  42  * The SLICOSS driver for Alacritech's IS-NIC products.
  43  *
  44  * This driver is supposed to support:
  45  *
  46  *      Mojave cards (single port PCI Gigabit) both copper and fiber
  47  *      Oasis cards (single and dual port PCI-x Gigabit) copper and fiber
  48  *      Kalahari cards (dual and quad port PCI-e Gigabit) copper and fiber
  49  *
  50  * The driver was acutally tested on Oasis and Kalahari cards.
  51  *
  52  *
  53  * NOTE: This is the standard, non-accelerated version of Alacritech's
  54  *       IS-NIC driver.
  55  */
  56
  57
  58 #define KLUDGE_FOR_4GB_BOUNDARY         1
  59 #define DEBUG_MICROCODE                 1
  60 #define DBG                             1
  61 #define SLIC_INTERRUPT_PROCESS_LIMIT    1
  62 #define SLIC_OFFLOAD_IP_CHECKSUM                1
  63 #define STATS_TIMER_INTERVAL                    2
  64 #define PING_TIMER_INTERVAL                         1
  65
  66 #include <linux/kernel.h>
  67 #include <linux/string.h>
  68 #include <linux/errno.h>
  69 #include <linux/ioport.h>
  70 #include <linux/slab.h>
  71 #include <linux/interrupt.h>
  72 #include <linux/timer.h>
  73 #include <linux/pci.h>
  74 #include <linux/spinlock.h>
  75 #include <linux/init.h>
  76 #include <linux/bitops.h>
  77 #include <linux/io.h>
  78 #include <linux/netdevice.h>
  79 #include <linux/etherdevice.h>
  80 #include <linux/skbuff.h>
  81 #include <linux/delay.h>
  82 #include <linux/debugfs.h>
  83 #include <linux/seq_file.h>
  84 #include <linux/kthread.h>
  85 #include <linux/module.h>
  86 #include <linux/moduleparam.h>
  87
  88 #include <linux/firmware.h>
  89 #include <linux/types.h>
  90 #include <linux/dma-mapping.h>
  91 #include <linux/mii.h>
  92 #include <linux/if_vlan.h>
  93 #include <asm/unaligned.h>
  94
  95 #include <linux/ethtool.h>
  96 #include <linux/uaccess.h>
  97 #include "slichw.h"
  98 #include "slic.h"
  99
 100 static struct net_device_stats *slic_get_stats(struct net_device *dev);
 101 static int slic_entry_open(struct net_device *dev);
 102 static int slic_entry_halt(struct net_device *dev);
 103 static int slic_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 104 static netdev_tx_t slic_xmit_start(struct sk_buff *skb, struct net_device *dev);
 105 static void slic_xmit_fail(struct adapter *adapter, struct sk_buff *skb,
 106                            void *cmd, u32 skbtype, u32 status);
 107 static void slic_config_pci(struct pci_dev *pcidev);
 108 static struct sk_buff *slic_rcvqueue_getnext(struct adapter *adapter);
 109 static int slic_mac_set_address(struct net_device *dev, void *ptr);
 110 static void slic_link_event_handler(struct adapter *adapter);
 111 static void slic_upr_request_complete(struct adapter *adapter, u32 isr);
 112 static int slic_rspqueue_init(struct adapter *adapter);
 113 static void slic_rspqueue_free(struct adapter *adapter);
 114 static struct slic_rspbuf *slic_rspqueue_getnext(struct adapter *adapter);
 115 static int slic_cmdq_init(struct adapter *adapter);
 116 static void slic_cmdq_free(struct adapter *adapter);
 117 static void slic_cmdq_reset(struct adapter *adapter);
 118 static void slic_cmdq_addcmdpage(struct adapter *adapter, u32 *page);
 119 static void slic_cmdq_getdone(struct adapter *adapter);
 120 static void slic_cmdq_putdone_irq(struct adapter *adapter,
 121                                   struct slic_hostcmd *cmd);
 122 static struct slic_hostcmd *slic_cmdq_getfree(struct adapter *adapter);
 123 static int slic_rcvqueue_init(struct adapter *adapter);
 124 static int slic_rcvqueue_fill(struct adapter *adapter);
 125 static u32 slic_rcvqueue_reinsert(struct adapter *adapter, struct sk_buff *skb);
 126 static void slic_rcvqueue_free(struct adapter *adapter);
 127 static void slic_adapter_set_hwaddr(struct adapter *adapter);
 128 static int slic_card_init(struct sliccard *card, struct adapter *adapter);
 129 static void slic_intagg_set(struct adapter *adapter, u32 value);
 130 static int slic_card_download(struct adapter *adapter);
 131 static u32 slic_card_locate(struct adapter *adapter);
 132 static int slic_if_init(struct adapter *adapter);
 133 static int slic_adapter_allocresources(struct adapter *adapter);
 134 static void slic_adapter_freeresources(struct adapter *adapter);
 135 static void slic_link_config(struct adapter *adapter, u32 linkspeed,
 136                              u32 linkduplex);
 137 static void slic_unmap_mmio_space(struct adapter *adapter);
 138 static void slic_card_cleanup(struct sliccard *card);
 139 static void slic_soft_reset(struct adapter *adapter);
 140 static bool slic_mac_filter(struct adapter *adapter,
 141                             struct ether_header *ether_frame);
 142 static void slic_mac_address_config(struct adapter *adapter);
 143 static void slic_mac_config(struct adapter *adapter);
 144 static void slic_mcast_set_mask(struct adapter *adapter);
 145 static void slic_config_set(struct adapter *adapter, bool linkchange);
 146 static void slic_config_clear(struct adapter *adapter);
 147 static void slic_config_get(struct adapter *adapter, u32 config,
 148                             u32 configh);
 149 static void slic_timer_load_check(ulong context);
 150 static void slic_assert_fail(void);
 151 static ushort slic_eeprom_cksum(char *m, int len);
 152 static void slic_upr_start(struct adapter *adapter);
 153 static void slic_link_upr_complete(struct adapter *adapter, u32 Isr);
 154 static int  slic_upr_request(struct adapter *adapter, u32 upr_request,
 155                              u32 upr_data, u32 upr_data_h, u32 upr_buffer,
 156                              u32 upr_buffer_h);
 157 static void slic_mcast_set_list(struct net_device *dev);
 158
 159
 160 static uint slic_first_init = 1;
 161 static char *slic_banner = "Alacritech SLIC Technology(tm) Server "\
 162                 "and Storage Accelerator (Non-Accelerated)";
 163
 164 static char *slic_proc_version = "2.0.351  2006/07/14 12:26:00";
 165 static char *slic_product_name = "SLIC Technology(tm) Server "\
 166                 "and Storage Accelerator (Non-Accelerated)";
 167 static char *slic_vendor = "Alacritech, Inc.";
 168
 169 static int slic_debug = 1;
 170 static int debug = -1;
 171 static struct net_device *head_netdevice;
 172
 173 static struct base_driver slic_global = { {}, 0, 0, 0, 1, NULL, NULL };
 174 static int intagg_delay = 100;
 175 static u32 dynamic_intagg;
 176 static unsigned int rcv_count;
 177 static struct dentry *slic_debugfs;
 178
 179 #define DRV_NAME          "slicoss"
 180 #define DRV_VERSION       "2.0.1"
 181 #define DRV_AUTHOR        "Alacritech, Inc. Engineering"
 182 #define DRV_DESCRIPTION   "Alacritech SLIC Techonology(tm) "\
 183                 "Non-Accelerated Driver"
 184 #define DRV_COPYRIGHT     "Copyright  2000-2006 Alacritech, Inc. "\
 185                 "All rights reserved."
 186 #define PFX                DRV_NAME " "
 187
 188 MODULE_AUTHOR(DRV_AUTHOR);
 189 MODULE_DESCRIPTION(DRV_DESCRIPTION);
 190 MODULE_LICENSE("Dual BSD/GPL");
 191
 192 module_param(dynamic_intagg, int, 0);
 193 MODULE_PARM_DESC(dynamic_intagg, "Dynamic Interrupt Aggregation Setting");
 194 module_param(intagg_delay, int, 0);
 195 MODULE_PARM_DESC(intagg_delay, "uSec Interrupt Aggregation Delay");
 196
 197 static struct pci_device_id slic_pci_tbl[] __devinitdata = {
 198         {PCI_VENDOR_ID_ALACRITECH,
 199          SLIC_1GB_DEVICE_ID,
 200          PCI_ANY_ID, PCI_ANY_ID,},
 201         {PCI_VENDOR_ID_ALACRITECH,
 202          SLIC_2GB_DEVICE_ID,
 203          PCI_ANY_ID, PCI_ANY_ID,},
 204         {0,}
 205 };
 206
 207 MODULE_DEVICE_TABLE(pci, slic_pci_tbl);
 208
 209 #ifdef ASSERT
 210 #undef ASSERT
 211 #endif
 212
 213 #ifndef ASSERT
 214 #define ASSERT(a) do {                                                  \
 215         if (!(a)) {                                                     \
 216                 printk(KERN_ERR "slicoss ASSERT() Failure: function %s" \
 217                         "line %d\n", __func__, __LINE__);               \
 218                 slic_assert_fail();                                     \
 219         }                                                               \
 220 } while (0)
 221 #endif
 222
 223
 224 #define SLIC_GET_SLIC_HANDLE(_adapter, _pslic_handle)                   \
 225 {                                                                       \
 226     spin_lock_irqsave(&_adapter->handle_lock.lock,                      \
 227                         _adapter->handle_lock.flags);                   \
 228     _pslic_handle  =  _adapter->pfree_slic_handles;                     \
 229     if (_pslic_handle) {                                                \
 230         ASSERT(_pslic_handle->type == SLIC_HANDLE_FREE);                \
 231         _adapter->pfree_slic_handles = _pslic_handle->next;             \
 232     }                                                                   \
 233     spin_unlock_irqrestore(&_adapter->handle_lock.lock,                 \
 234                         _adapter->handle_lock.flags);                   \
 235 }
 236
 237 #define SLIC_FREE_SLIC_HANDLE(_adapter, _pslic_handle)                  \
 238 {                                                                       \
 239     _pslic_handle->type = SLIC_HANDLE_FREE;                             \
 240     spin_lock_irqsave(&_adapter->handle_lock.lock,                      \
 241                         _adapter->handle_lock.flags);                   \
 242     _pslic_handle->next = _adapter->pfree_slic_handles;                 \
 243     _adapter->pfree_slic_handles = _pslic_handle;                       \
 244     spin_unlock_irqrestore(&_adapter->handle_lock.lock,                 \
 245                         _adapter->handle_lock.flags);                   \
 246 }
 247
 248 static void slic_debug_init(void);
 249 static void slic_debug_cleanup(void);
 250 static void slic_debug_adapter_create(struct adapter *adapter);
 251 static void slic_debug_adapter_destroy(struct adapter *adapter);
 252 static void slic_debug_card_create(struct sliccard *card);
 253 static void slic_debug_card_destroy(struct sliccard *card);
 254
 255 static inline void slic_reg32_write(void __iomem *reg, u32 value, bool flush)
 256 {
 257         writel(value, reg);
 258         if (flush)
 259                 mb();
 260 }
 261
 262 static inline void slic_reg64_write(struct adapter *adapter, void __iomem *reg,
 263                                     u32 value, void __iomem *regh, u32 paddrh,
 264                                     bool flush)
 265 {
 266         spin_lock_irqsave(&adapter->bit64reglock.lock,
 267                                 adapter->bit64reglock.flags);
 268         if (paddrh != adapter->curaddrupper) {
 269                 adapter->curaddrupper = paddrh;
 270                 writel(paddrh, regh);
 271         }
 272         writel(value, reg);
 273         if (flush)
 274                 mb();
 275         spin_unlock_irqrestore(&adapter->bit64reglock.lock,
 276                                 adapter->bit64reglock.flags);
 277 }
 278
 279 static void slic_init_driver(void)
 280 {
 281         if (slic_first_init) {
 282                 slic_first_init = 0;
 283                 spin_lock_init(&slic_global.driver_lock.lock);
 284                 slic_debug_init();
 285         }
 286 }
 287
 288 static void slic_init_adapter(struct net_device *netdev,
 289                               struct pci_dev *pcidev,
 290                               const struct pci_device_id *pci_tbl_entry,
 291                               void __iomem *memaddr, int chip_idx)
 292 {
 293         ushort index;
 294         struct slic_handle *pslic_handle;
 295         struct adapter *adapter = (struct adapter *)netdev_priv(netdev);
 296
 297 /*      adapter->pcidev = pcidev;*/
 298         adapter->vendid = pci_tbl_entry->vendor;
 299         adapter->devid = pci_tbl_entry->device;
 300         adapter->subsysid = pci_tbl_entry->subdevice;
 301         adapter->busnumber = pcidev->bus->number;
 302         adapter->slotnumber = ((pcidev->devfn >> 3) & 0x1F);
 303         adapter->functionnumber = (pcidev->devfn & 0x7);
 304         adapter->memorylength = pci_resource_len(pcidev, 0);
 305         adapter->slic_regs = (__iomem struct slic_regs *)memaddr;
 306         adapter->irq = pcidev->irq;
 307 /*      adapter->netdev = netdev;*/
 308         adapter->next_netdevice = head_netdevice;
 309         head_netdevice = netdev;
 310         adapter->chipid = chip_idx;
 311         adapter->port = 0;      /*adapter->functionnumber;*/
 312         adapter->cardindex = adapter->port;
 313         adapter->memorybase = memaddr;
 314         spin_lock_init(&adapter->upr_lock.lock);
 315         spin_lock_init(&adapter->bit64reglock.lock);
 316         spin_lock_init(&adapter->adapter_lock.lock);
 317         spin_lock_init(&adapter->reset_lock.lock);
 318         spin_lock_init(&adapter->handle_lock.lock);
 319
 320         adapter->card_size = 1;
 321         /*
 322           Initialize slic_handle array
 323         */
 324         ASSERT(SLIC_CMDQ_MAXCMDS <= 0xFFFF);
 325         /*
 326          Start with 1.  0 is an invalid host handle.
 327         */
 328         for (index = 1, pslic_handle = &adapter->slic_handles[1];
 329              index < SLIC_CMDQ_MAXCMDS; index++, pslic_handle++) {
 330
 331                 pslic_handle->token.handle_index = index;
 332                 pslic_handle->type = SLIC_HANDLE_FREE;
 333                 pslic_handle->next = adapter->pfree_slic_handles;
 334                 adapter->pfree_slic_handles = pslic_handle;
 335         }
 336         adapter->pshmem = (struct slic_shmem *)
 337                                         pci_alloc_consistent(adapter->pcidev,
 338                                         sizeof(struct slic_shmem),
 339                                         &adapter->
 340                                         phys_shmem);
 341         ASSERT(adapter->pshmem);
 342
 343         memset(adapter->pshmem, 0, sizeof(struct slic_shmem));
 344
 345         return;
 346 }
 347
 348 static const struct net_device_ops slic_netdev_ops = {
 349         .ndo_open               = slic_entry_open,
 350         .ndo_stop               = slic_entry_halt,
 351         .ndo_start_xmit         = slic_xmit_start,
 352         .ndo_do_ioctl           = slic_ioctl,
 353         .ndo_set_mac_address    = slic_mac_set_address,
 354         .ndo_get_stats          = slic_get_stats,
 355         .ndo_set_multicast_list = slic_mcast_set_list,
 356         .ndo_validate_addr      = eth_validate_addr,
 357         .ndo_change_mtu         = eth_change_mtu,
 358 };
 359
 360 static int __devinit slic_entry_probe(struct pci_dev *pcidev,
 361                                const struct pci_device_id *pci_tbl_entry)
 362 {
 363         static int cards_found;
 364         static int did_version;
 365         int err = -ENODEV;
 366         struct net_device *netdev;
 367         struct adapter *adapter;
 368         void __iomem *memmapped_ioaddr = NULL;
 369         u32 status = 0;
 370         ulong mmio_start = 0;
 371         ulong mmio_len = 0;
 372         struct sliccard *card = NULL;
 373
 374         slic_global.dynamic_intagg = dynamic_intagg;
 375
 376         err = pci_enable_device(pcidev);
 377
 378         if (err)
 379                 return err;
 380
 381         if (slic_debug > 0 && did_version++ == 0) {
 382                 printk(KERN_DEBUG "%s\n", slic_banner);
 383                 printk(KERN_DEBUG "%s\n", slic_proc_version);
 384         }
 385
 386         err = pci_set_dma_mask(pcidev, DMA_BIT_MASK(64));
 387         if (err) {
 388                 err = pci_set_dma_mask(pcidev, DMA_BIT_MASK(32));
 389                 if (err)
 390                         goto err_out_disable_pci;
 391         }
 392
 393         err = pci_request_regions(pcidev, DRV_NAME);
 394         if (err)
 395                 goto err_out_disable_pci;
 396
 397         pci_set_master(pcidev);
 398
 399         netdev = alloc_etherdev(sizeof(struct adapter));
 400         if (!netdev) {
 401                 err = -ENOMEM;
 402                 goto err_out_exit_slic_probe;
 403         }
 404
 405         SET_NETDEV_DEV(netdev, &pcidev->dev);
 406
 407         pci_set_drvdata(pcidev, netdev);
 408         adapter = netdev_priv(netdev);
 409         adapter->netdev = netdev;
 410         adapter->pcidev = pcidev;
 411
 412         mmio_start = pci_resource_start(pcidev, 0);
 413         mmio_len = pci_resource_len(pcidev, 0);
 414
 415
 416 /*      memmapped_ioaddr =  (u32)ioremap_nocache(mmio_start, mmio_len);*/
 417         memmapped_ioaddr = ioremap(mmio_start, mmio_len);
 418         if (!memmapped_ioaddr) {
 419                 dev_err(&pcidev->dev, "cannot remap MMIO region %lx @ %lx\n",
 420                         mmio_len, mmio_start);
 421                 goto err_out_free_netdev;
 422         }
 423
 424         slic_config_pci(pcidev);
 425
 426         slic_init_driver();
 427
 428         slic_init_adapter(netdev,
 429                           pcidev, pci_tbl_entry, memmapped_ioaddr, cards_found);
 430
 431         status = slic_card_locate(adapter);
 432         if (status) {
 433                 dev_err(&pcidev->dev, "cannot locate card\n");
 434                 goto err_out_free_mmio_region;
 435         }
 436
 437         card = adapter->card;
 438
 439         if (!adapter->allocated) {
 440                 card->adapters_allocated++;
 441                 adapter->allocated = 1;
 442         }
 443
 444         status = slic_card_init(card, adapter);
 445
 446         if (status != STATUS_SUCCESS) {
 447                 card->state = CARD_FAIL;
 448                 adapter->state = ADAPT_FAIL;
 449                 adapter->linkstate = LINK_DOWN;
 450                 dev_err(&pcidev->dev, "FAILED status[%x]\n", status);
 451         } else {
 452                 slic_adapter_set_hwaddr(adapter);
 453         }
 454
 455         netdev->base_addr = (unsigned long)adapter->memorybase;
 456         netdev->irq = adapter->irq;
 457         netdev->netdev_ops = &slic_netdev_ops;
 458
 459         slic_debug_adapter_create(adapter);
 460
 461         strcpy(netdev->name, "eth%d");
 462         err = register_netdev(netdev);
 463         if (err) {
 464                 dev_err(&pcidev->dev, "Cannot register net device, aborting.\n");
 465                 goto err_out_unmap;
 466         }
 467
 468         cards_found++;
 469
 470         return status;
 471
 472 err_out_unmap:
 473         iounmap(memmapped_ioaddr);
 474 err_out_free_mmio_region:
 475         release_mem_region(mmio_start, mmio_len);
 476 err_out_free_netdev:
 477         free_netdev(netdev);
 478 err_out_exit_slic_probe:
 479         pci_release_regions(pcidev);
 480 err_out_disable_pci:
 481         pci_disable_device(pcidev);
 482         return err;
 483 }
 484
 485 static int slic_entry_open(struct net_device *dev)
 486 {
 487         struct adapter *adapter = (struct adapter *) netdev_priv(dev);
 488         struct sliccard *card = adapter->card;
 489         u32 locked = 0;
 490         int status;
 491
 492         ASSERT(adapter);
 493         ASSERT(card);
 494
 495         netif_stop_queue(adapter->netdev);
 496
 497         spin_lock_irqsave(&slic_global.driver_lock.lock,
 498                                 slic_global.driver_lock.flags);
 499         locked = 1;
 500         if (!adapter->activated) {
 501                 card->adapters_activated++;
 502                 slic_global.num_slic_ports_active++;
 503                 adapter->activated = 1;
 504         }
 505         status = slic_if_init(adapter);
 506
 507         if (status != STATUS_SUCCESS) {
 508                 if (adapter->activated) {
 509                         card->adapters_activated--;
 510                         slic_global.num_slic_ports_active--;
 511                         adapter->activated = 0;
 512                 }
 513                 if (locked) {
 514                         spin_unlock_irqrestore(&slic_global.driver_lock.lock,
 515                                                 slic_global.driver_lock.flags);
 516                         locked = 0;
 517                 }
 518                 return status;
 519         }
 520         if (!card->master)
 521                 card->master = adapter;
 522
 523         if (locked) {
 524                 spin_unlock_irqrestore(&slic_global.driver_lock.lock,
 525                                         slic_global.driver_lock.flags);
 526                 locked = 0;
 527         }
 528
 529         return STATUS_SUCCESS;
 530 }
 531
 532 static void __devexit slic_entry_remove(struct pci_dev *pcidev)
 533 {
 534         struct net_device *dev = pci_get_drvdata(pcidev);
 535         u32 mmio_start = 0;
 536         uint mmio_len = 0;
 537         struct adapter *adapter = (struct adapter *) netdev_priv(dev);
 538         struct sliccard *card;
 539         struct mcast_address *mcaddr, *mlist;
 540
 541         ASSERT(adapter);
 542         slic_adapter_freeresources(adapter);
 543         slic_unmap_mmio_space(adapter);
 544         unregister_netdev(dev);
 545
 546         mmio_start = pci_resource_start(pcidev, 0);
 547         mmio_len = pci_resource_len(pcidev, 0);
 548
 549         release_mem_region(mmio_start, mmio_len);
 550
 551         iounmap((void __iomem *)dev->base_addr);
 552         /* free multicast addresses */
 553         mlist = adapter->mcastaddrs;
 554         while (mlist) {
 555                 mcaddr = mlist;
 556                 mlist = mlist->next;
 557                 kfree(mcaddr);
 558         }
 559         ASSERT(adapter->card);
 560         card = adapter->card;
 561         ASSERT(card->adapters_allocated);
 562         card->adapters_allocated--;
 563         adapter->allocated = 0;
 564         if (!card->adapters_allocated) {
 565                 struct sliccard *curr_card = slic_global.slic_card;
 566                 if (curr_card == card) {
 567                         slic_global.slic_card = card->next;
 568                 } else {
 569                         while (curr_card->next != card)
 570                                 curr_card = curr_card->next;
 571                         ASSERT(curr_card);
 572                         curr_card->next = card->next;
 573                 }
 574                 ASSERT(slic_global.num_slic_cards);
 575                 slic_global.num_slic_cards--;
 576                 slic_card_cleanup(card);
 577         }
 578         kfree(dev);
 579         pci_release_regions(pcidev);
 580 }
 581
 582 static int slic_entry_halt(struct net_device *dev)
 583 {
 584         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
 585         struct sliccard *card = adapter->card;
 586         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
 587
 588         spin_lock_irqsave(&slic_global.driver_lock.lock,
 589                                 slic_global.driver_lock.flags);
 590         ASSERT(card);
 591         netif_stop_queue(adapter->netdev);
 592         adapter->state = ADAPT_DOWN;
 593         adapter->linkstate = LINK_DOWN;
 594         adapter->upr_list = NULL;
 595         adapter->upr_busy = 0;
 596         adapter->devflags_prev = 0;
 597         ASSERT(card->adapter[adapter->cardindex] == adapter);
 598         slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH);
 599         adapter->all_reg_writes++;
 600         adapter->icr_reg_writes++;
 601         slic_config_clear(adapter);
 602         if (adapter->activated) {
 603                 card->adapters_activated--;
 604                 slic_global.num_slic_ports_active--;
 605                 adapter->activated = 0;
 606         }
 607 #ifdef AUTOMATIC_RESET
 608         slic_reg32_write(&slic_regs->slic_reset_iface, 0, FLUSH);
 609 #endif
 610         /*
 611          *  Reset the adapter's cmd queues
 612          */
 613         slic_cmdq_reset(adapter);
 614
 615 #ifdef AUTOMATIC_RESET
 616         if (!card->adapters_activated)
 617                 slic_card_init(card, adapter);
 618 #endif
 619
 620         spin_unlock_irqrestore(&slic_global.driver_lock.lock,
 621                                 slic_global.driver_lock.flags);
 622         return STATUS_SUCCESS;
 623 }
 624
 625 static int slic_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 626 {
 627         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
 628         struct ethtool_cmd edata;
 629         struct ethtool_cmd ecmd;
 630         u32 data[7];
 631         u32 intagg;
 632
 633         ASSERT(rq);
 634         switch (cmd) {
 635         case SIOCSLICSETINTAGG:
 636                 if (copy_from_user(data, rq->ifr_data, 28))
 637                         return -EFAULT;
 638                 intagg = data[0];
 639                 dev_err(&dev->dev, "%s: set interrupt aggregation to %d\n",
 640                         __func__, intagg);
 641                 slic_intagg_set(adapter, intagg);
 642                 return 0;
 643
 644 #ifdef SLIC_TRACE_DUMP_ENABLED
 645         case SIOCSLICTRACEDUMP:
 646                 {
 647                         u32 value;
 648                         DBG_IOCTL("slic_ioctl  SIOCSLIC_TRACE_DUMP\n");
 649
 650                         if (copy_from_user(data, rq->ifr_data, 28)) {
 651                                 PRINT_ERROR
 652                                     ("slic: copy_from_user FAILED getting \
 653                                      initial simba param\n");
 654                                 return -EFAULT;
 655                         }
 656
 657                         value = data[0];
 658                         if (tracemon_request == SLIC_DUMP_DONE) {
 659                                 PRINT_ERROR
 660                                     ("ATK Diagnostic Trace Dump Requested\n");
 661                                 tracemon_request = SLIC_DUMP_REQUESTED;
 662                                 tracemon_request_type = value;
 663                                 tracemon_timestamp = jiffies;
 664                         } else if ((tracemon_request == SLIC_DUMP_REQUESTED) ||
 665                                    (tracemon_request ==
 666                                     SLIC_DUMP_IN_PROGRESS)) {
 667                                 PRINT_ERROR
 668                                     ("ATK Diagnostic Trace Dump Requested but \
 669                                      already in progress... ignore\n");
 670                         } else {
 671                                 PRINT_ERROR
 672                                     ("ATK Diagnostic Trace Dump Requested\n");
 673                                 tracemon_request = SLIC_DUMP_REQUESTED;
 674                                 tracemon_request_type = value;
 675                                 tracemon_timestamp = jiffies;
 676                         }
 677                         return 0;
 678                 }
 679 #endif
 680         case SIOCETHTOOL:
 681                 ASSERT(adapter);
 682                 if (copy_from_user(&ecmd, rq->ifr_data, sizeof(ecmd)))
 683                         return -EFAULT;
 684
 685                 if (ecmd.cmd == ETHTOOL_GSET) {
 686                         edata.supported = (SUPPORTED_10baseT_Half |
 687                                            SUPPORTED_10baseT_Full |
 688                                            SUPPORTED_100baseT_Half |
 689                                            SUPPORTED_100baseT_Full |
 690                                            SUPPORTED_Autoneg | SUPPORTED_MII);
 691                         edata.port = PORT_MII;
 692                         edata.transceiver = XCVR_INTERNAL;
 693                         edata.phy_address = 0;
 694                         if (adapter->linkspeed == LINK_100MB)
 695                                 edata.speed = SPEED_100;
 696                         else if (adapter->linkspeed == LINK_10MB)
 697                                 edata.speed = SPEED_10;
 698                         else
 699                                 edata.speed = 0;
 700
 701                         if (adapter->linkduplex == LINK_FULLD)
 702                                 edata.duplex = DUPLEX_FULL;
 703                         else
 704                                 edata.duplex = DUPLEX_HALF;
 705
 706                         edata.autoneg = AUTONEG_ENABLE;
 707                         edata.maxtxpkt = 1;
 708                         edata.maxrxpkt = 1;
 709                         if (copy_to_user(rq->ifr_data, &edata, sizeof(edata)))
 710                                 return -EFAULT;
 711
 712                 } else if (ecmd.cmd == ETHTOOL_SSET) {
 713                         if (!capable(CAP_NET_ADMIN))
 714                                 return -EPERM;
 715
 716                         if (adapter->linkspeed == LINK_100MB)
 717                                 edata.speed = SPEED_100;
 718                         else if (adapter->linkspeed == LINK_10MB)
 719                                 edata.speed = SPEED_10;
 720                         else
 721                                 edata.speed = 0;
 722
 723                         if (adapter->linkduplex == LINK_FULLD)
 724                                 edata.duplex = DUPLEX_FULL;
 725                         else
 726                                 edata.duplex = DUPLEX_HALF;
 727
 728                         edata.autoneg = AUTONEG_ENABLE;
 729                         edata.maxtxpkt = 1;
 730                         edata.maxrxpkt = 1;
 731                         if ((ecmd.speed != edata.speed) ||
 732                             (ecmd.duplex != edata.duplex)) {
 733                                 u32 speed;
 734                                 u32 duplex;
 735
 736                                 if (ecmd.speed == SPEED_10)
 737                                         speed = 0;
 738                                 else
 739                                         speed = PCR_SPEED_100;
 740                                 if (ecmd.duplex == DUPLEX_FULL)
 741                                         duplex = PCR_DUPLEX_FULL;
 742                                 else
 743                                         duplex = 0;
 744                                 slic_link_config(adapter, speed, duplex);
 745                                 slic_link_event_handler(adapter);
 746                         }
 747                 }
 748                 return 0;
 749         default:
 750                 return -EOPNOTSUPP;
 751         }
 752 }
 753
 754 #define  XMIT_FAIL_LINK_STATE               1
 755 #define  XMIT_FAIL_ZERO_LENGTH              2
 756 #define  XMIT_FAIL_HOSTCMD_FAIL             3
 757
 758 static void slic_xmit_build_request(struct adapter *adapter,
 759                              struct slic_hostcmd *hcmd, struct sk_buff *skb)
 760 {
 761         struct slic_host64_cmd *ihcmd;
 762         ulong phys_addr;
 763
 764         ihcmd = &hcmd->cmd64;
 765
 766         ihcmd->flags = (adapter->port << IHFLG_IFSHFT);
 767         ihcmd->command = IHCMD_XMT_REQ;
 768         ihcmd->u.slic_buffers.totlen = skb->len;
 769         phys_addr = pci_map_single(adapter->pcidev, skb->data, skb->len,
 770                         PCI_DMA_TODEVICE);
 771         ihcmd->u.slic_buffers.bufs[0].paddrl = SLIC_GET_ADDR_LOW(phys_addr);
 772         ihcmd->u.slic_buffers.bufs[0].paddrh = SLIC_GET_ADDR_HIGH(phys_addr);
 773         ihcmd->u.slic_buffers.bufs[0].length = skb->len;
 774 #if defined(CONFIG_X86_64)
 775         hcmd->cmdsize = (u32) ((((u64)&ihcmd->u.slic_buffers.bufs[1] -
 776                                      (u64) hcmd) + 31) >> 5);
 777 #elif defined(CONFIG_X86)
 778         hcmd->cmdsize = ((((u32) &ihcmd->u.slic_buffers.bufs[1] -
 779                            (u32) hcmd) + 31) >> 5);
 780 #else
 781         Stop Compilation;
 782 #endif
 783 }
 784
 785 #define NORMAL_ETHFRAME     0
 786
 787 static netdev_tx_t slic_xmit_start(struct sk_buff *skb, struct net_device *dev)
 788 {
 789         struct sliccard *card;
 790         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
 791         struct slic_hostcmd *hcmd = NULL;
 792         u32 status = 0;
 793         u32 skbtype = NORMAL_ETHFRAME;
 794         void *offloadcmd = NULL;
 795
 796         card = adapter->card;
 797         ASSERT(card);
 798         if ((adapter->linkstate != LINK_UP) ||
 799             (adapter->state != ADAPT_UP) || (card->state != CARD_UP)) {
 800                 status = XMIT_FAIL_LINK_STATE;
 801                 goto xmit_fail;
 802
 803         } else if (skb->len == 0) {
 804                 status = XMIT_FAIL_ZERO_LENGTH;
 805                 goto xmit_fail;
 806         }
 807
 808         if (skbtype == NORMAL_ETHFRAME) {
 809                 hcmd = slic_cmdq_getfree(adapter);
 810                 if (!hcmd) {
 811                         adapter->xmitq_full = 1;
 812                         status = XMIT_FAIL_HOSTCMD_FAIL;
 813                         goto xmit_fail;
 814                 }
 815                 ASSERT(hcmd->pslic_handle);
 816                 ASSERT(hcmd->cmd64.hosthandle ==
 817                        hcmd->pslic_handle->token.handle_token);
 818                 hcmd->skb = skb;
 819                 hcmd->busy = 1;
 820                 hcmd->type = SLIC_CMD_DUMB;
 821                 if (skbtype == NORMAL_ETHFRAME)
 822                         slic_xmit_build_request(adapter, hcmd, skb);
 823         }
 824         adapter->stats.tx_packets++;
 825         adapter->stats.tx_bytes += skb->len;
 826
 827 #ifdef DEBUG_DUMP
 828         if (adapter->kill_card) {
 829                 struct slic_host64_cmd ihcmd;
 830
 831                 ihcmd = &hcmd->cmd64;
 832
 833                 ihcmd->flags |= 0x40;
 834                 adapter->kill_card = 0; /* only do this once */
 835         }
 836 #endif
 837         if (hcmd->paddrh == 0) {
 838                 slic_reg32_write(&adapter->slic_regs->slic_cbar,
 839                                  (hcmd->paddrl | hcmd->cmdsize), DONT_FLUSH);
 840         } else {
 841                 slic_reg64_write(adapter, &adapter->slic_regs->slic_cbar64,
 842                                  (hcmd->paddrl | hcmd->cmdsize),
 843                                  &adapter->slic_regs->slic_addr_upper,
 844                                  hcmd->paddrh, DONT_FLUSH);
 845         }
 846 xmit_done:
 847         return NETDEV_TX_OK;
 848 xmit_fail:
 849         slic_xmit_fail(adapter, skb, offloadcmd, skbtype, status);
 850         goto xmit_done;
 851 }
 852
 853 static void slic_xmit_fail(struct adapter *adapter,
 854                     struct sk_buff *skb,
 855                     void *cmd, u32 skbtype, u32 status)
 856 {
 857         if (adapter->xmitq_full)
 858                 netif_stop_queue(adapter->netdev);
 859         if ((cmd == NULL) && (status <= XMIT_FAIL_HOSTCMD_FAIL)) {
 860                 switch (status) {
 861                 case XMIT_FAIL_LINK_STATE:
 862                         dev_err(&adapter->netdev->dev,
 863                                 "reject xmit skb[%p: %x] linkstate[%s] "
 864                                 "adapter[%s:%d] card[%s:%d]\n",
 865                                 skb, skb->pkt_type,
 866                                 SLIC_LINKSTATE(adapter->linkstate),
 867                                 SLIC_ADAPTER_STATE(adapter->state),
 868                                 adapter->state,
 869                                 SLIC_CARD_STATE(adapter->card->state),
 870                                 adapter->card->state);
 871                         break;
 872                 case XMIT_FAIL_ZERO_LENGTH:
 873                         dev_err(&adapter->netdev->dev,
 874                                 "xmit_start skb->len == 0 skb[%p] type[%x]\n",
 875                                 skb, skb->pkt_type);
 876                         break;
 877                 case XMIT_FAIL_HOSTCMD_FAIL:
 878                         dev_err(&adapter->netdev->dev,
 879                                 "xmit_start skb[%p] type[%x] No host commands "
 880                                 "available\n", skb, skb->pkt_type);
 881                         break;
 882                 default:
 883                         ASSERT(0);
 884                 }
 885         }
 886         dev_kfree_skb(skb);
 887         adapter->stats.tx_dropped++;
 888 }
 889
 890 static void slic_rcv_handle_error(struct adapter *adapter,
 891                                         struct slic_rcvbuf *rcvbuf)
 892 {
 893         struct slic_hddr_wds *hdr = (struct slic_hddr_wds *)rcvbuf->data;
 894
 895         if (adapter->devid != SLIC_1GB_DEVICE_ID) {
 896                 if (hdr->frame_status14 & VRHSTAT_802OE)
 897                         adapter->if_events.oflow802++;
 898                 if (hdr->frame_status14 & VRHSTAT_TPOFLO)
 899                         adapter->if_events.Tprtoflow++;
 900                 if (hdr->frame_status_b14 & VRHSTATB_802UE)
 901                         adapter->if_events.uflow802++;
 902                 if (hdr->frame_status_b14 & VRHSTATB_RCVE) {
 903                         adapter->if_events.rcvearly++;
 904                         adapter->stats.rx_fifo_errors++;
 905                 }
 906                 if (hdr->frame_status_b14 & VRHSTATB_BUFF) {
 907                         adapter->if_events.Bufov++;
 908                         adapter->stats.rx_over_errors++;
 909                 }
 910                 if (hdr->frame_status_b14 & VRHSTATB_CARRE) {
 911                         adapter->if_events.Carre++;
 912                         adapter->stats.tx_carrier_errors++;
 913                 }
 914                 if (hdr->frame_status_b14 & VRHSTATB_LONGE)
 915                         adapter->if_events.Longe++;
 916                 if (hdr->frame_status_b14 & VRHSTATB_PREA)
 917                         adapter->if_events.Invp++;
 918                 if (hdr->frame_status_b14 & VRHSTATB_CRC) {
 919                         adapter->if_events.Crc++;
 920                         adapter->stats.rx_crc_errors++;
 921                 }
 922                 if (hdr->frame_status_b14 & VRHSTATB_DRBL)
 923                         adapter->if_events.Drbl++;
 924                 if (hdr->frame_status_b14 & VRHSTATB_CODE)
 925                         adapter->if_events.Code++;
 926                 if (hdr->frame_status_b14 & VRHSTATB_TPCSUM)
 927                         adapter->if_events.TpCsum++;
 928                 if (hdr->frame_status_b14 & VRHSTATB_TPHLEN)
 929                         adapter->if_events.TpHlen++;
 930                 if (hdr->frame_status_b14 & VRHSTATB_IPCSUM)
 931                         adapter->if_events.IpCsum++;
 932                 if (hdr->frame_status_b14 & VRHSTATB_IPLERR)
 933                         adapter->if_events.IpLen++;
 934                 if (hdr->frame_status_b14 & VRHSTATB_IPHERR)
 935                         adapter->if_events.IpHlen++;
 936         } else {
 937                 if (hdr->frame_statusGB & VGBSTAT_XPERR) {
 938                         u32 xerr = hdr->frame_statusGB >> VGBSTAT_XERRSHFT;
 939
 940                         if (xerr == VGBSTAT_XCSERR)
 941                                 adapter->if_events.TpCsum++;
 942                         if (xerr == VGBSTAT_XUFLOW)
 943                                 adapter->if_events.Tprtoflow++;
 944                         if (xerr == VGBSTAT_XHLEN)
 945                                 adapter->if_events.TpHlen++;
 946                 }
 947                 if (hdr->frame_statusGB & VGBSTAT_NETERR) {
 948                         u32 nerr =
 949                             (hdr->
 950                              frame_statusGB >> VGBSTAT_NERRSHFT) &
 951                             VGBSTAT_NERRMSK;
 952                         if (nerr == VGBSTAT_NCSERR)
 953                                 adapter->if_events.IpCsum++;
 954                         if (nerr == VGBSTAT_NUFLOW)
 955                                 adapter->if_events.IpLen++;
 956                         if (nerr == VGBSTAT_NHLEN)
 957                                 adapter->if_events.IpHlen++;
 958                 }
 959                 if (hdr->frame_statusGB & VGBSTAT_LNKERR) {
 960                         u32 lerr = hdr->frame_statusGB & VGBSTAT_LERRMSK;
 961
 962                         if (lerr == VGBSTAT_LDEARLY)
 963                                 adapter->if_events.rcvearly++;
 964                         if (lerr == VGBSTAT_LBOFLO)
 965                                 adapter->if_events.Bufov++;
 966                         if (lerr == VGBSTAT_LCODERR)
 967                                 adapter->if_events.Code++;
 968                         if (lerr == VGBSTAT_LDBLNBL)
 969                                 adapter->if_events.Drbl++;
 970                         if (lerr == VGBSTAT_LCRCERR)
 971                                 adapter->if_events.Crc++;
 972                         if (lerr == VGBSTAT_LOFLO)
 973                                 adapter->if_events.oflow802++;
 974                         if (lerr == VGBSTAT_LUFLO)
 975                                 adapter->if_events.uflow802++;
 976                 }
 977         }
 978         return;
 979 }
 980
 981 #define TCP_OFFLOAD_FRAME_PUSHFLAG  0x10000000
 982 #define M_FAST_PATH                 0x0040
 983
 984 static void slic_rcv_handler(struct adapter *adapter)
 985 {
 986         struct sk_buff *skb;
 987         struct slic_rcvbuf *rcvbuf;
 988         u32 frames = 0;
 989
 990         while ((skb = slic_rcvqueue_getnext(adapter))) {
 991                 u32 rx_bytes;
 992
 993                 ASSERT(skb->head);
 994                 rcvbuf = (struct slic_rcvbuf *)skb->head;
 995                 adapter->card->events++;
 996                 if (rcvbuf->status & IRHDDR_ERR) {
 997                         adapter->rx_errors++;
 998                         slic_rcv_handle_error(adapter, rcvbuf);
 999                         slic_rcvqueue_reinsert(adapter, skb);
1000                         continue;
1001                 }
1002
1003                 if (!slic_mac_filter(adapter, (struct ether_header *)
1004                                         rcvbuf->data)) {
1005                         slic_rcvqueue_reinsert(adapter, skb);
1006                         continue;
1007                 }
1008                 skb_pull(skb, SLIC_RCVBUF_HEADSIZE);
1009                 rx_bytes = (rcvbuf->length & IRHDDR_FLEN_MSK);
1010                 skb_put(skb, rx_bytes);
1011                 adapter->stats.rx_packets++;
1012                 adapter->stats.rx_bytes += rx_bytes;
1013 #if SLIC_OFFLOAD_IP_CHECKSUM
1014                 skb->ip_summed = CHECKSUM_UNNECESSARY;
1015 #endif
1016
1017                 skb->dev = adapter->netdev;
1018                 skb->protocol = eth_type_trans(skb, skb->dev);
1019                 netif_rx(skb);
1020
1021                 ++frames;
1022 #if SLIC_INTERRUPT_PROCESS_LIMIT
1023                 if (frames >= SLIC_RCVQ_MAX_PROCESS_ISR) {
1024                         adapter->rcv_interrupt_yields++;
1025                         break;
1026                 }
1027 #endif
1028         }
1029         adapter->max_isr_rcvs = max(adapter->max_isr_rcvs, frames);
1030 }
1031
1032 static void slic_xmit_complete(struct adapter *adapter)
1033 {
1034         struct slic_hostcmd *hcmd;
1035         struct slic_rspbuf *rspbuf;
1036         u32 frames = 0;
1037         struct slic_handle_word slic_handle_word;
1038
1039         do {
1040                 rspbuf = slic_rspqueue_getnext(adapter);
1041                 if (!rspbuf)
1042                         break;
1043                 adapter->xmit_completes++;
1044                 adapter->card->events++;
1045                 /*
1046                  Get the complete host command buffer
1047                 */
1048                 slic_handle_word.handle_token = rspbuf->hosthandle;
1049                 ASSERT(slic_handle_word.handle_index);
1050                 ASSERT(slic_handle_word.handle_index <= SLIC_CMDQ_MAXCMDS);
1051                 hcmd =
1052                     (struct slic_hostcmd *)
1053                         adapter->slic_handles[slic_handle_word.handle_index].
1054                                                                         address;
1055 /*      hcmd = (struct slic_hostcmd *) rspbuf->hosthandle; */
1056                 ASSERT(hcmd);
1057                 ASSERT(hcmd->pslic_handle ==
1058                        &adapter->slic_handles[slic_handle_word.handle_index]);
1059                 if (hcmd->type == SLIC_CMD_DUMB) {
1060                         if (hcmd->skb)
1061                                 dev_kfree_skb_irq(hcmd->skb);
1062                         slic_cmdq_putdone_irq(adapter, hcmd);
1063                 }
1064                 rspbuf->status = 0;
1065                 rspbuf->hosthandle = 0;
1066                 frames++;
1067         } while (1);
1068         adapter->max_isr_xmits = max(adapter->max_isr_xmits, frames);
1069 }
1070
1071 static irqreturn_t slic_interrupt(int irq, void *dev_id)
1072 {
1073         struct net_device *dev = (struct net_device *)dev_id;
1074         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
1075         u32 isr;
1076
1077         if ((adapter->pshmem) && (adapter->pshmem->isr)) {
1078                 slic_reg32_write(&adapter->slic_regs->slic_icr,
1079                                  ICR_INT_MASK, FLUSH);
1080                 isr = adapter->isrcopy = adapter->pshmem->isr;
1081                 adapter->pshmem->isr = 0;
1082                 adapter->num_isrs++;
1083                 switch (adapter->card->state) {
1084                 case CARD_UP:
1085                         if (isr & ~ISR_IO) {
1086                                 if (isr & ISR_ERR) {
1087                                         adapter->error_interrupts++;
1088                                         if (isr & ISR_RMISS) {
1089                                                 int count;
1090                                                 int pre_count;
1091                                                 int errors;
1092
1093                                                 struct slic_rcvqueue *rcvq =
1094                                                     &adapter->rcvqueue;
1095
1096                                                 adapter->
1097                                                     error_rmiss_interrupts++;
1098                                                 if (!rcvq->errors)
1099                                                         rcv_count = rcvq->count;
1100                                                 pre_count = rcvq->count;
1101                                                 errors = rcvq->errors;
1102
1103                                                 while (rcvq->count <
1104                                                        SLIC_RCVQ_FILLTHRESH) {
1105                                                         count =
1106                                                             slic_rcvqueue_fill
1107                                                             (adapter);
1108                                                         if (!count)
1109                                                                 break;
1110                                                 }
1111                                         } else if (isr & ISR_XDROP) {
1112                                                 dev_err(&dev->dev,
1113                                                         "isr & ISR_ERR [%x] "
1114                                                         "ISR_XDROP \n", isr);
1115                                         } else {
1116                                                 dev_err(&dev->dev,
1117                                                         "isr & ISR_ERR [%x]\n",
1118                                                         isr);
1119                                         }
1120                                 }
1121
1122                                 if (isr & ISR_LEVENT) {
1123                                         adapter->linkevent_interrupts++;
1124                                         slic_link_event_handler(adapter);
1125                                 }
1126
1127                                 if ((isr & ISR_UPC) ||
1128                                     (isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) {
1129                                         adapter->upr_interrupts++;
1130                                         slic_upr_request_complete(adapter, isr);
1131                                 }
1132                         }
1133
1134                         if (isr & ISR_RCV) {
1135                                 adapter->rcv_interrupts++;
1136                                 slic_rcv_handler(adapter);
1137                         }
1138
1139                         if (isr & ISR_CMD) {
1140                                 adapter->xmit_interrupts++;
1141                                 slic_xmit_complete(adapter);
1142                         }
1143                         break;
1144
1145                 case CARD_DOWN:
1146                         if ((isr & ISR_UPC) ||
1147                             (isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) {
1148                                 adapter->upr_interrupts++;
1149                                 slic_upr_request_complete(adapter, isr);
1150                         }
1151                         break;
1152
1153                 default:
1154                         break;
1155                 }
1156
1157                 adapter->isrcopy = 0;
1158                 adapter->all_reg_writes += 2;
1159                 adapter->isr_reg_writes++;
1160                 slic_reg32_write(&adapter->slic_regs->slic_isr, 0, FLUSH);
1161         } else {
1162                 adapter->false_interrupts++;
1163         }
1164         return IRQ_HANDLED;
1165 }
1166
1167 /*
1168  * slic_link_event_handler -
1169  *
1170  * Initiate a link configuration sequence.  The link configuration begins
1171  * by issuing a READ_LINK_STATUS command to the Utility Processor on the
1172  * SLIC.  Since the command finishes asynchronously, the slic_upr_comlete
1173  * routine will follow it up witha UP configuration write command, which
1174  * will also complete asynchronously.
1175  *
1176  */
1177 static void slic_link_event_handler(struct adapter *adapter)
1178 {
1179         int status;
1180         struct slic_shmem *pshmem;
1181
1182         if (adapter->state != ADAPT_UP) {
1183                 /* Adapter is not operational.  Ignore.  */
1184                 return;
1185         }
1186
1187         pshmem = (struct slic_shmem *)adapter->phys_shmem;
1188
1189 #if defined(CONFIG_X86_64)
1190         status = slic_upr_request(adapter,
1191                                   SLIC_UPR_RLSR,
1192                                   SLIC_GET_ADDR_LOW(&pshmem->linkstatus),
1193                                   SLIC_GET_ADDR_HIGH(&pshmem->linkstatus),
1194                                   0, 0);
1195 #elif defined(CONFIG_X86)
1196         status = slic_upr_request(adapter, SLIC_UPR_RLSR,
1197                 (u32) &pshmem->linkstatus,      /* no 4GB wrap guaranteed */
1198                                   0, 0, 0);
1199 #else
1200         Stop compilation;
1201 #endif
1202         ASSERT((status == STATUS_SUCCESS) || (status == STATUS_PENDING));
1203 }
1204
1205 static void slic_init_cleanup(struct adapter *adapter)
1206 {
1207         if (adapter->intrregistered) {
1208                 adapter->intrregistered = 0;
1209                 free_irq(adapter->netdev->irq, adapter->netdev);
1210
1211         }
1212         if (adapter->pshmem) {
1213                 pci_free_consistent(adapter->pcidev,
1214                                     sizeof(struct slic_shmem),
1215                                     adapter->pshmem, adapter->phys_shmem);
1216                 adapter->pshmem = NULL;
1217                 adapter->phys_shmem = (dma_addr_t) NULL;
1218         }
1219
1220         if (adapter->pingtimerset) {
1221                 adapter->pingtimerset = 0;
1222                 del_timer(&adapter->pingtimer);
1223         }
1224
1225         slic_rspqueue_free(adapter);
1226         slic_cmdq_free(adapter);
1227         slic_rcvqueue_free(adapter);
1228 }
1229
1230 static struct net_device_stats *slic_get_stats(struct net_device *dev)
1231 {
1232         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
1233         struct net_device_stats *stats;
1234
1235         ASSERT(adapter);
1236         stats = &adapter->stats;
1237         stats->collisions = adapter->slic_stats.iface.xmit_collisions;
1238         stats->rx_errors = adapter->slic_stats.iface.rcv_errors;
1239         stats->tx_errors = adapter->slic_stats.iface.xmt_errors;
1240         stats->rx_missed_errors = adapter->slic_stats.iface.rcv_discards;
1241         stats->tx_heartbeat_errors = 0;
1242         stats->tx_aborted_errors = 0;
1243         stats->tx_window_errors = 0;
1244         stats->tx_fifo_errors = 0;
1245         stats->rx_frame_errors = 0;
1246         stats->rx_length_errors = 0;
1247         return &adapter->stats;
1248 }
1249
1250 /*
1251  *  Allocate a mcast_address structure to hold the multicast address.
1252  *  Link it in.
1253  */
1254 static int slic_mcast_add_list(struct adapter *adapter, char *address)
1255 {
1256         struct mcast_address *mcaddr, *mlist;
1257         bool equaladdr;
1258
1259         /* Check to see if it already exists */
1260         mlist = adapter->mcastaddrs;
1261         while (mlist) {
1262                 ETHER_EQ_ADDR(mlist->address, address, equaladdr);
1263                 if (equaladdr)
1264                         return STATUS_SUCCESS;
1265                 mlist = mlist->next;
1266         }
1267
1268         /* Doesn't already exist.  Allocate a structure to hold it */
1269         mcaddr = kmalloc(sizeof(struct mcast_address), GFP_ATOMIC);
1270         if (mcaddr == NULL)
1271                 return 1;
1272
1273         memcpy(mcaddr->address, address, 6);
1274
1275         mcaddr->next = adapter->mcastaddrs;
1276         adapter->mcastaddrs = mcaddr;
1277
1278         return STATUS_SUCCESS;
1279 }
1280
1281 /*
1282  * Functions to obtain the CRC corresponding to the destination mac address.
1283  * This is a standard ethernet CRC in that it is a 32-bit, reflected CRC using
1284  * the polynomial:
1285  *   x^32 + x^26 + x^23 + x^22 + x^16 + x^12 + x^11 + x^10 + x^8 + x^7 + x^5 +
1286  *   x^4 + x^2 + x^1.
1287  *
1288  * After the CRC for the 6 bytes is generated (but before the value is
1289  * complemented),
1290  * we must then transpose the value and return bits 30-23.
1291  *
1292  */
1293 static u32 slic_crc_table[256]; /* Table of CRCs for all possible byte values */
1294 static u32 slic_crc_init;       /* Is table initialized */
1295
1296 /*
1297  *  Contruct the CRC32 table
1298  */
1299 static void slic_mcast_init_crc32(void)
1300 {
1301         u32 c;          /*  CRC shit reg                 */
1302         u32 e = 0;              /*  Poly X-or pattern            */
1303         int i;                  /*  counter                      */
1304         int k;                  /*  byte being shifted into crc  */
1305
1306         static int p[] = { 0, 1, 2, 4, 5, 7, 8, 10, 11, 12, 16, 22, 23, 26 };
1307
1308         for (i = 0; i < ARRAY_SIZE(p); i++)
1309                 e |= 1L << (31 - p[i]);
1310
1311         for (i = 1; i < 256; i++) {
1312                 c = i;
1313                 for (k = 8; k; k--)
1314                         c = c & 1 ? (c >> 1) ^ e : c >> 1;
1315                 slic_crc_table[i] = c;
1316         }
1317 }
1318
1319 /*
1320  *  Return the MAC hast as described above.
1321  */
1322 static unsigned char slic_mcast_get_mac_hash(char *macaddr)
1323 {
1324         u32 crc;
1325         char *p;
1326         int i;
1327         unsigned char machash = 0;
1328
1329         if (!slic_crc_init) {
1330                 slic_mcast_init_crc32();
1331                 slic_crc_init = 1;
1332         }
1333
1334         crc = 0xFFFFFFFF;       /* Preload shift register, per crc-32 spec */
1335         for (i = 0, p = macaddr; i < 6; ++p, ++i)
1336                 crc = (crc >> 8) ^ slic_crc_table[(crc ^ *p) & 0xFF];
1337
1338         /* Return bits 1-8, transposed */
1339         for (i = 1; i < 9; i++)
1340                 machash |= (((crc >> i) & 1) << (8 - i));
1341
1342         return machash;
1343 }
1344
1345 static void slic_mcast_set_bit(struct adapter *adapter, char *address)
1346 {
1347         unsigned char crcpoly;
1348
1349         /* Get the CRC polynomial for the mac address */
1350         crcpoly = slic_mcast_get_mac_hash(address);
1351
1352         /* We only have space on the SLIC for 64 entries.  Lop
1353          * off the top two bits. (2^6 = 64)
1354          */
1355         crcpoly &= 0x3F;
1356
1357         /* OR in the new bit into our 64 bit mask. */
1358         adapter->mcastmask |= (u64) 1 << crcpoly;
1359 }
1360
1361 static void slic_mcast_set_list(struct net_device *dev)
1362 {
1363         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
1364         int status = STATUS_SUCCESS;
1365         int i;
1366         char *addresses;
1367         struct dev_mc_list *mc_list = dev->mc_list;
1368         int mc_count = dev->mc_count;
1369
1370         ASSERT(adapter);
1371
1372         for (i = 1; i <= mc_count; i++) {
1373                 addresses = (char *) &mc_list->dmi_addr;
1374                 if (mc_list->dmi_addrlen == 6) {
1375                         status = slic_mcast_add_list(adapter, addresses);
1376                         if (status != STATUS_SUCCESS)
1377                                 break;
1378                 } else {
1379                         status = -EINVAL;
1380                         break;
1381                 }
1382                 slic_mcast_set_bit(adapter, addresses);
1383                 mc_list = mc_list->next;
1384         }
1385
1386         if (adapter->devflags_prev != dev->flags) {
1387                 adapter->macopts = MAC_DIRECTED;
1388                 if (dev->flags) {
1389                         if (dev->flags & IFF_BROADCAST)
1390                                 adapter->macopts |= MAC_BCAST;
1391                         if (dev->flags & IFF_PROMISC)
1392                                 adapter->macopts |= MAC_PROMISC;
1393                         if (dev->flags & IFF_ALLMULTI)
1394                                 adapter->macopts |= MAC_ALLMCAST;
1395                         if (dev->flags & IFF_MULTICAST)
1396                                 adapter->macopts |= MAC_MCAST;
1397                 }
1398                 adapter->devflags_prev = dev->flags;
1399                 slic_config_set(adapter, true);
1400         } else {
1401                 if (status == STATUS_SUCCESS)
1402                         slic_mcast_set_mask(adapter);
1403         }
1404         return;
1405 }
1406
1407 static void slic_mcast_set_mask(struct adapter *adapter)
1408 {
1409         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1410
1411         if (adapter->macopts & (MAC_ALLMCAST | MAC_PROMISC)) {
1412                 /* Turn on all multicast addresses. We have to do this for
1413                  * promiscuous mode as well as ALLMCAST mode.  It saves the
1414                  * Microcode from having to keep state about the MAC
1415                  * configuration.
1416                  */
1417                 slic_reg32_write(&slic_regs->slic_mcastlow, 0xFFFFFFFF, FLUSH);
1418                 slic_reg32_write(&slic_regs->slic_mcasthigh, 0xFFFFFFFF,
1419                                  FLUSH);
1420         } else {
1421                 /* Commit our multicast mast to the SLIC by writing to the
1422                  * multicast address mask registers
1423                  */
1424                 slic_reg32_write(&slic_regs->slic_mcastlow,
1425                         (u32)(adapter->mcastmask & 0xFFFFFFFF), FLUSH);
1426                 slic_reg32_write(&slic_regs->slic_mcasthigh,
1427                         (u32)((adapter->mcastmask >> 32) & 0xFFFFFFFF), FLUSH);
1428         }
1429 }
1430
1431 static void slic_timer_ping(ulong dev)
1432 {
1433         struct adapter *adapter;
1434         struct sliccard *card;
1435
1436         ASSERT(dev);
1437         adapter = netdev_priv((struct net_device *)dev);
1438         ASSERT(adapter);
1439         card = adapter->card;
1440         ASSERT(card);
1441
1442         adapter->pingtimer.expires = jiffies + (PING_TIMER_INTERVAL * HZ);
1443         add_timer(&adapter->pingtimer);
1444 }
1445
1446 /*
1447  *  slic_if_init
1448  *
1449  *  Perform initialization of our slic interface.
1450  *
1451  */
1452 static int slic_if_init(struct adapter *adapter)
1453 {
1454         struct sliccard *card = adapter->card;
1455         struct net_device *dev = adapter->netdev;
1456         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1457         struct slic_shmem *pshmem;
1458         int status = 0;
1459
1460         ASSERT(card);
1461
1462         /* adapter should be down at this point */
1463         if (adapter->state != ADAPT_DOWN) {
1464                 dev_err(&dev->dev, "%s: adapter->state != ADAPT_DOWN\n",
1465                         __func__);
1466                 return -EIO;
1467         }
1468         ASSERT(adapter->linkstate == LINK_DOWN);
1469
1470         adapter->devflags_prev = dev->flags;
1471         adapter->macopts = MAC_DIRECTED;
1472         if (dev->flags) {
1473                 if (dev->flags & IFF_BROADCAST)
1474                         adapter->macopts |= MAC_BCAST;
1475                 if (dev->flags & IFF_PROMISC)
1476                         adapter->macopts |= MAC_PROMISC;
1477                 if (dev->flags & IFF_ALLMULTI)
1478                         adapter->macopts |= MAC_ALLMCAST;
1479                 if (dev->flags & IFF_MULTICAST)
1480                         adapter->macopts |= MAC_MCAST;
1481         }
1482         status = slic_adapter_allocresources(adapter);
1483         if (status != STATUS_SUCCESS) {
1484                 dev_err(&dev->dev,
1485                         "%s: slic_adapter_allocresources FAILED %x\n",
1486                         __func__, status);
1487                 slic_adapter_freeresources(adapter);
1488                 return status;
1489         }
1490
1491         if (!adapter->queues_initialized) {
1492                 if (slic_rspqueue_init(adapter))
1493                         return -ENOMEM;
1494                 if (slic_cmdq_init(adapter))
1495                         return -ENOMEM;
1496                 if (slic_rcvqueue_init(adapter))
1497                         return -ENOMEM;
1498                 adapter->queues_initialized = 1;
1499         }
1500
1501         slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH);
1502         mdelay(1);
1503
1504         if (!adapter->isp_initialized) {
1505                 pshmem = (struct slic_shmem *)adapter->phys_shmem;
1506
1507                 spin_lock_irqsave(&adapter->bit64reglock.lock,
1508                                         adapter->bit64reglock.flags);
1509
1510 #if defined(CONFIG_X86_64)
1511                 slic_reg32_write(&slic_regs->slic_addr_upper,
1512                                  SLIC_GET_ADDR_HIGH(&pshmem->isr), DONT_FLUSH);
1513                 slic_reg32_write(&slic_regs->slic_isp,
1514                                  SLIC_GET_ADDR_LOW(&pshmem->isr), FLUSH);
1515 #elif defined(CONFIG_X86)
1516                 slic_reg32_write(&slic_regs->slic_addr_upper, 0, DONT_FLUSH);
1517                 slic_reg32_write(&slic_regs->slic_isp, (u32)&pshmem->isr, FLUSH);
1518 #else
1519                 Stop Compilations
1520 #endif
1521                 spin_unlock_irqrestore(&adapter->bit64reglock.lock,
1522                                         adapter->bit64reglock.flags);
1523                 adapter->isp_initialized = 1;
1524         }
1525
1526         adapter->state = ADAPT_UP;
1527         if (!card->loadtimerset) {
1528                 init_timer(&card->loadtimer);
1529                 card->loadtimer.expires =
1530                     jiffies + (SLIC_LOADTIMER_PERIOD * HZ);
1531                 card->loadtimer.data = (ulong) card;
1532                 card->loadtimer.function = &slic_timer_load_check;
1533                 add_timer(&card->loadtimer);
1534
1535                 card->loadtimerset = 1;
1536         }
1537
1538         if (!adapter->pingtimerset) {
1539                 init_timer(&adapter->pingtimer);
1540                 adapter->pingtimer.expires =
1541                     jiffies + (PING_TIMER_INTERVAL * HZ);
1542                 adapter->pingtimer.data = (ulong) dev;
1543                 adapter->pingtimer.function = &slic_timer_ping;
1544                 add_timer(&adapter->pingtimer);
1545                 adapter->pingtimerset = 1;
1546                 adapter->card->pingstatus = ISR_PINGMASK;
1547         }
1548
1549         /*
1550          *    clear any pending events, then enable interrupts
1551          */
1552         adapter->isrcopy = 0;
1553         adapter->pshmem->isr = 0;
1554         slic_reg32_write(&slic_regs->slic_isr, 0, FLUSH);
1555         slic_reg32_write(&slic_regs->slic_icr, ICR_INT_ON, FLUSH);
1556
1557         slic_link_config(adapter, LINK_AUTOSPEED, LINK_AUTOD);
1558         slic_link_event_handler(adapter);
1559
1560         return STATUS_SUCCESS;
1561 }
1562
1563 static void slic_unmap_mmio_space(struct adapter *adapter)
1564 {
1565         if (adapter->slic_regs)
1566                 iounmap(adapter->slic_regs);
1567         adapter->slic_regs = NULL;
1568 }
1569
1570 static int slic_adapter_allocresources(struct adapter *adapter)
1571 {
1572         if (!adapter->intrregistered) {
1573                 int retval;
1574
1575                 spin_unlock_irqrestore(&slic_global.driver_lock.lock,
1576                                         slic_global.driver_lock.flags);
1577
1578                 retval = request_irq(adapter->netdev->irq,
1579                                      &slic_interrupt,
1580                                      IRQF_SHARED,
1581                                      adapter->netdev->name, adapter->netdev);
1582
1583                 spin_lock_irqsave(&slic_global.driver_lock.lock,
1584                                         slic_global.driver_lock.flags);
1585
1586                 if (retval) {
1587                         dev_err(&adapter->netdev->dev,
1588                                 "request_irq (%s) FAILED [%x]\n",
1589                                 adapter->netdev->name, retval);
1590                         return retval;
1591                 }
1592                 adapter->intrregistered = 1;
1593         }
1594         return STATUS_SUCCESS;
1595 }
1596
1597 static void slic_config_pci(struct pci_dev *pcidev)
1598 {
1599         u16 pci_command;
1600         u16 new_command;
1601
1602         pci_read_config_word(pcidev, PCI_COMMAND, &pci_command);
1603
1604         new_command = pci_command | PCI_COMMAND_MASTER
1605             | PCI_COMMAND_MEMORY
1606             | PCI_COMMAND_INVALIDATE
1607             | PCI_COMMAND_PARITY | PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK;
1608         if (pci_command != new_command)
1609                 pci_write_config_word(pcidev, PCI_COMMAND, new_command);
1610 }
1611
1612 static void slic_adapter_freeresources(struct adapter *adapter)
1613 {
1614         slic_init_cleanup(adapter);
1615         memset(&adapter->stats, 0, sizeof(struct net_device_stats));
1616         adapter->error_interrupts = 0;
1617         adapter->rcv_interrupts = 0;
1618         adapter->xmit_interrupts = 0;
1619         adapter->linkevent_interrupts = 0;
1620         adapter->upr_interrupts = 0;
1621         adapter->num_isrs = 0;
1622         adapter->xmit_completes = 0;
1623         adapter->rcv_broadcasts = 0;
1624         adapter->rcv_multicasts = 0;
1625         adapter->rcv_unicasts = 0;
1626 }
1627
1628 /*
1629  *  slic_link_config
1630  *
1631  *  Write phy control to configure link duplex/speed
1632  *
1633  */
1634 static void slic_link_config(struct adapter *adapter,
1635                       u32 linkspeed, u32 linkduplex)
1636 {
1637         u32 __iomem *wphy;
1638         u32 speed;
1639         u32 duplex;
1640         u32 phy_config;
1641         u32 phy_advreg;
1642         u32 phy_gctlreg;
1643
1644         if (adapter->state != ADAPT_UP)
1645                 return;
1646
1647         ASSERT((adapter->devid == SLIC_1GB_DEVICE_ID)
1648                || (adapter->devid == SLIC_2GB_DEVICE_ID));
1649
1650         if (linkspeed > LINK_1000MB)
1651                 linkspeed = LINK_AUTOSPEED;
1652         if (linkduplex > LINK_AUTOD)
1653                 linkduplex = LINK_AUTOD;
1654
1655         wphy = &adapter->slic_regs->slic_wphy;
1656
1657         if ((linkspeed == LINK_AUTOSPEED) || (linkspeed == LINK_1000MB)) {
1658                 if (adapter->flags & ADAPT_FLAGS_FIBERMEDIA) {
1659                         /*  We've got a fiber gigabit interface, and register
1660                          *  4 is different in fiber mode than in copper mode
1661                          */
1662
1663                         /* advertise FD only @1000 Mb */
1664                         phy_advreg = (MIICR_REG_4 | (PAR_ADV1000XFD));
1665                         /* enable PAUSE frames        */
1666                         phy_advreg |= PAR_ASYMPAUSE_FIBER;
1667                         slic_reg32_write(wphy, phy_advreg, FLUSH);
1668
1669                         if (linkspeed == LINK_AUTOSPEED) {
1670                                 /* reset phy, enable auto-neg  */
1671                                 phy_config =
1672                                     (MIICR_REG_PCR |
1673                                      (PCR_RESET | PCR_AUTONEG |
1674                                       PCR_AUTONEG_RST));
1675                                 slic_reg32_write(wphy, phy_config, FLUSH);
1676                         } else {        /* forced 1000 Mb FD*/
1677                                 /* power down phy to break link
1678                                    this may not work) */
1679                                 phy_config = (MIICR_REG_PCR | PCR_POWERDOWN);
1680                                 slic_reg32_write(wphy, phy_config, FLUSH);
1681                                 /* wait, Marvell says 1 sec,
1682                                    try to get away with 10 ms  */
1683                                 mdelay(10);
1684
1685                                 /* disable auto-neg, set speed/duplex,
1686                                    soft reset phy, powerup */
1687                                 phy_config =
1688                                     (MIICR_REG_PCR |
1689                                      (PCR_RESET | PCR_SPEED_1000 |
1690                                       PCR_DUPLEX_FULL));
1691                                 slic_reg32_write(wphy, phy_config, FLUSH);
1692                         }
1693                 } else {        /* copper gigabit */
1694
1695                         /* Auto-Negotiate or 1000 Mb must be auto negotiated
1696                          * We've got a copper gigabit interface, and
1697                          * register 4 is different in copper mode than
1698                          * in fiber mode
1699                          */
1700                         if (linkspeed == LINK_AUTOSPEED) {
1701                                 /* advertise 10/100 Mb modes   */
1702                                 phy_advreg =
1703                                     (MIICR_REG_4 |
1704                                      (PAR_ADV100FD | PAR_ADV100HD | PAR_ADV10FD
1705                                       | PAR_ADV10HD));
1706                         } else {
1707                         /* linkspeed == LINK_1000MB -
1708                            don't advertise 10/100 Mb modes  */
1709                                 phy_advreg = MIICR_REG_4;
1710                         }
1711                         /* enable PAUSE frames  */
1712                         phy_advreg |= PAR_ASYMPAUSE;
1713                         /* required by the Cicada PHY  */
1714                         phy_advreg |= PAR_802_3;
1715                         slic_reg32_write(wphy, phy_advreg, FLUSH);
1716                         /* advertise FD only @1000 Mb  */
1717                         phy_gctlreg = (MIICR_REG_9 | (PGC_ADV1000FD));
1718                         slic_reg32_write(wphy, phy_gctlreg, FLUSH);
1719
1720                         if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) {
1721                                 /* if a Marvell PHY
1722                                    enable auto crossover */
1723                                 phy_config =
1724                                     (MIICR_REG_16 | (MRV_REG16_XOVERON));
1725                                 slic_reg32_write(wphy, phy_config, FLUSH);
1726
1727                                 /* reset phy, enable auto-neg  */
1728                                 phy_config =
1729                                     (MIICR_REG_PCR |
1730                                      (PCR_RESET | PCR_AUTONEG |
1731                                       PCR_AUTONEG_RST));
1732                                 slic_reg32_write(wphy, phy_config, FLUSH);
1733                         } else {        /* it's a Cicada PHY  */
1734                                 /* enable and restart auto-neg (don't reset)  */
1735                                 phy_config =
1736                                     (MIICR_REG_PCR |
1737                                      (PCR_AUTONEG | PCR_AUTONEG_RST));
1738                                 slic_reg32_write(wphy, phy_config, FLUSH);
1739                         }
1740                 }
1741         } else {
1742                 /* Forced 10/100  */
1743                 if (linkspeed == LINK_10MB)
1744                         speed = 0;
1745                 else
1746                         speed = PCR_SPEED_100;
1747                 if (linkduplex == LINK_HALFD)
1748                         duplex = 0;
1749                 else
1750                         duplex = PCR_DUPLEX_FULL;
1751
1752                 if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) {
1753                         /* if a Marvell PHY
1754                            disable auto crossover  */
1755                         phy_config = (MIICR_REG_16 | (MRV_REG16_XOVEROFF));
1756                         slic_reg32_write(wphy, phy_config, FLUSH);
1757                 }
1758
1759                 /* power down phy to break link (this may not work)  */
1760                 phy_config = (MIICR_REG_PCR | (PCR_POWERDOWN | speed | duplex));
1761                 slic_reg32_write(wphy, phy_config, FLUSH);
1762
1763                 /* wait, Marvell says 1 sec, try to get away with 10 ms */
1764                 mdelay(10);
1765
1766                 if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) {
1767                         /* if a Marvell PHY
1768                            disable auto-neg, set speed,
1769                            soft reset phy, powerup */
1770                         phy_config =
1771                             (MIICR_REG_PCR | (PCR_RESET | speed | duplex));
1772                         slic_reg32_write(wphy, phy_config, FLUSH);
1773                 } else {        /* it's a Cicada PHY  */
1774                         /* disable auto-neg, set speed, powerup  */
1775                         phy_config = (MIICR_REG_PCR | (speed | duplex));
1776                         slic_reg32_write(wphy, phy_config, FLUSH);
1777                 }
1778         }
1779 }
1780
1781 static void slic_card_cleanup(struct sliccard *card)
1782 {
1783         if (card->loadtimerset) {
1784                 card->loadtimerset = 0;
1785                 del_timer(&card->loadtimer);
1786         }
1787
1788         slic_debug_card_destroy(card);
1789
1790         kfree(card);
1791 }
1792
1793 static int slic_card_download_gbrcv(struct adapter *adapter)
1794 {
1795         const struct firmware *fw;
1796         const char *file = "";
1797         int ret;
1798         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1799         u32 codeaddr;
1800         u32 instruction;
1801         int index = 0;
1802         u32 rcvucodelen = 0;
1803
1804         switch (adapter->devid) {
1805         case SLIC_2GB_DEVICE_ID:
1806                 file = "slicoss/oasisrcvucode.sys";
1807                 break;
1808         case SLIC_1GB_DEVICE_ID:
1809                 file = "slicoss/gbrcvucode.sys";
1810                 break;
1811         default:
1812                 ASSERT(0);
1813                 break;
1814         }
1815
1816         ret = request_firmware(&fw, file, &adapter->pcidev->dev);
1817         if (ret) {
1818                 dev_err(&adapter->pcidev->dev,
1819                         "SLICOSS: Failed to load firmware %s\n", file);
1820                 return ret;
1821         }
1822
1823         rcvucodelen = *(u32 *)(fw->data + index);
1824         index += 4;
1825         switch (adapter->devid) {
1826         case SLIC_2GB_DEVICE_ID:
1827                 if (rcvucodelen != OasisRcvUCodeLen)
1828                         return -EINVAL;
1829                 break;
1830         case SLIC_1GB_DEVICE_ID:
1831                 if (rcvucodelen != GBRcvUCodeLen)
1832                         return -EINVAL;
1833                 break;
1834         default:
1835                 ASSERT(0);
1836                 break;
1837         }
1838         /* start download */
1839         slic_reg32_write(&slic_regs->slic_rcv_wcs, SLIC_RCVWCS_BEGIN, FLUSH);
1840         /* download the rcv sequencer ucode */
1841         for (codeaddr = 0; codeaddr < rcvucodelen; codeaddr++) {
1842                 /* write out instruction address */
1843                 slic_reg32_write(&slic_regs->slic_rcv_wcs, codeaddr, FLUSH);
1844
1845                 instruction = *(u32 *)(fw->data + index);
1846                 index += 4;
1847                 /* write out the instruction data low addr */
1848                 slic_reg32_write(&slic_regs->slic_rcv_wcs, instruction, FLUSH);
1849
1850                 instruction = *(u8 *)(fw->data + index);
1851                 index++;
1852                 /* write out the instruction data high addr */
1853                 slic_reg32_write(&slic_regs->slic_rcv_wcs, (u8)instruction,
1854                                  FLUSH);
1855         }
1856
1857         /* download finished */
1858         release_firmware(fw);
1859         slic_reg32_write(&slic_regs->slic_rcv_wcs, SLIC_RCVWCS_FINISH, FLUSH);
1860         return 0;
1861 }
1862
1863 static int slic_card_download(struct adapter *adapter)
1864 {
1865         const struct firmware *fw;
1866         const char *file = "";
1867         int ret;
1868         u32 section;
1869         int thissectionsize;
1870         int codeaddr;
1871         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1872         u32 instruction;
1873         u32 baseaddress;
1874         u32 i;
1875         u32 numsects = 0;
1876         u32 sectsize[3];
1877         u32 sectstart[3];
1878         int ucode_start, index = 0;
1879
1880         switch (adapter->devid) {
1881         case SLIC_2GB_DEVICE_ID:
1882                 file = "slicoss/oasisdownload.sys";
1883                 break;
1884         case SLIC_1GB_DEVICE_ID:
1885                 file = "slicoss/gbdownload.sys";
1886                 break;
1887         default:
1888                 ASSERT(0);
1889                 break;
1890         }
1891         ret = request_firmware(&fw, file, &adapter->pcidev->dev);
1892         if (ret) {
1893                 dev_err(&adapter->pcidev->dev,
1894                         "SLICOSS: Failed to load firmware %s\n", file);
1895                 return ret;
1896         }
1897         numsects = *(u32 *)(fw->data + index);
1898         index += 4;
1899         ASSERT(numsects <= 3);
1900         for (i = 0; i < numsects; i++) {
1901                 sectsize[i] = *(u32 *)(fw->data + index);
1902                 index += 4;
1903         }
1904         for (i = 0; i < numsects; i++) {
1905                 sectstart[i] = *(u32 *)(fw->data + index);
1906                 index += 4;
1907         }
1908         ucode_start = index;
1909         instruction = *(u32 *)(fw->data + index);
1910         index += 4;
1911         for (section = 0; section < numsects; section++) {
1912                 baseaddress = sectstart[section];
1913                 thissectionsize = sectsize[section] >> 3;
1914
1915                 for (codeaddr = 0; codeaddr < thissectionsize; codeaddr++) {
1916                         /* Write out instruction address */
1917                         slic_reg32_write(&slic_regs->slic_wcs,
1918                                          baseaddress + codeaddr, FLUSH);
1919                         /* Write out instruction to low addr */
1920                         slic_reg32_write(&slic_regs->slic_wcs, instruction, FLUSH);
1921                         instruction = *(u32 *)(fw->data + index);
1922                         index += 4;
1923
1924                         /* Write out instruction to high addr */
1925                         slic_reg32_write(&slic_regs->slic_wcs, instruction, FLUSH);
1926                         instruction = *(u32 *)(fw->data + index);
1927                         index += 4;
1928                 }
1929         }
1930         index = ucode_start;
1931         for (section = 0; section < numsects; section++) {
1932                 instruction = *(u32 *)(fw->data + index);
1933                 baseaddress = sectstart[section];
1934                 if (baseaddress < 0x8000)
1935                         continue;
1936                 thissectionsize = sectsize[section] >> 3;
1937
1938                 for (codeaddr = 0; codeaddr < thissectionsize; codeaddr++) {
1939                         /* Write out instruction address */
1940                         slic_reg32_write(&slic_regs->slic_wcs,
1941                                 SLIC_WCS_COMPARE | (baseaddress + codeaddr),
1942                                 FLUSH);
1943                         /* Write out instruction to low addr */
1944                         slic_reg32_write(&slic_regs->slic_wcs, instruction,
1945                                          FLUSH);
1946                         instruction = *(u32 *)(fw->data + index);
1947                         index += 4;
1948                         /* Write out instruction to high addr */
1949                         slic_reg32_write(&slic_regs->slic_wcs, instruction,
1950                                          FLUSH);
1951                         instruction = *(u32 *)(fw->data + index);
1952                         index += 4;
1953
1954                         /* Check SRAM location zero. If it is non-zero. Abort.*/
1955 /*                      failure = readl((u32 __iomem *)&slic_regs->slic_reset);
1956                         if (failure) {
1957                                 release_firmware(fw);
1958                                 return -EIO;
1959                         }*/
1960                 }
1961         }
1962         release_firmware(fw);
1963         /* Everything OK, kick off the card */
1964         mdelay(10);
1965         slic_reg32_write(&slic_regs->slic_wcs, SLIC_WCS_START, FLUSH);
1966
1967         /* stall for 20 ms, long enough for ucode to init card
1968            and reach mainloop */
1969         mdelay(20);
1970
1971         return STATUS_SUCCESS;
1972 }
1973
1974 static void slic_adapter_set_hwaddr(struct adapter *adapter)
1975 {
1976         struct sliccard *card = adapter->card;
1977
1978         if ((adapter->card) && (card->config_set)) {
1979                 memcpy(adapter->macaddr,
1980                        card->config.MacInfo[adapter->functionnumber].macaddrA,
1981                        sizeof(struct slic_config_mac));
1982                 if (!(adapter->currmacaddr[0] || adapter->currmacaddr[1] ||
1983                       adapter->currmacaddr[2] || adapter->currmacaddr[3] ||
1984                       adapter->currmacaddr[4] || adapter->currmacaddr[5])) {
1985                         memcpy(adapter->currmacaddr, adapter->macaddr, 6);
1986                 }
1987                 if (adapter->netdev) {
1988                         memcpy(adapter->netdev->dev_addr, adapter->currmacaddr,
1989                                6);
1990                 }
1991         }
1992 }
1993
1994 static void slic_intagg_set(struct adapter *adapter, u32 value)
1995 {
1996         slic_reg32_write(&adapter->slic_regs->slic_intagg, value, FLUSH);
1997         adapter->card->loadlevel_current = value;
1998 }
1999
2000 static int slic_card_init(struct sliccard *card, struct adapter *adapter)
2001 {
2002         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2003         struct slic_eeprom *peeprom;
2004         struct oslic_eeprom *pOeeprom;
2005         dma_addr_t phys_config;
2006         u32 phys_configh;
2007         u32 phys_configl;
2008         u32 i = 0;
2009         struct slic_shmem *pshmem;
2010         int status;
2011         uint macaddrs = card->card_size;
2012         ushort eecodesize;
2013         ushort dramsize;
2014         ushort ee_chksum;
2015         ushort calc_chksum;
2016         struct slic_config_mac *pmac;
2017         unsigned char fruformat;
2018         unsigned char oemfruformat;
2019         struct atk_fru *patkfru;
2020         union oemfru *poemfru;
2021
2022         /* Reset everything except PCI configuration space */
2023         slic_soft_reset(adapter);
2024
2025         /* Download the microcode */
2026         status = slic_card_download(adapter);
2027
2028         if (status != STATUS_SUCCESS) {
2029                 dev_err(&adapter->pcidev->dev,
2030                         "download failed bus %d slot %d\n",
2031                         adapter->busnumber, adapter->slotnumber);
2032                 return status;
2033         }
2034
2035         if (!card->config_set) {
2036                 peeprom = pci_alloc_consistent(adapter->pcidev,
2037                                                sizeof(struct slic_eeprom),
2038                                                &phys_config);
2039
2040                 phys_configl = SLIC_GET_ADDR_LOW(phys_config);
2041                 phys_configh = SLIC_GET_ADDR_HIGH(phys_config);
2042
2043                 if (!peeprom) {
2044                         dev_err(&adapter->pcidev->dev,
2045                                 "eeprom read failed to get memory "
2046                                 "bus %d slot %d\n", adapter->busnumber,
2047                                 adapter->slotnumber);
2048                         return -ENOMEM;
2049                 } else {
2050                         memset(peeprom, 0, sizeof(struct slic_eeprom));
2051                 }
2052                 slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH);
2053                 mdelay(1);
2054                 pshmem = (struct slic_shmem *)adapter->phys_shmem;
2055
2056                 spin_lock_irqsave(&adapter->bit64reglock.lock,
2057                                         adapter->bit64reglock.flags);
2058                 slic_reg32_write(&slic_regs->slic_addr_upper, 0, DONT_FLUSH);
2059                 slic_reg32_write(&slic_regs->slic_isp,
2060                                  SLIC_GET_ADDR_LOW(&pshmem->isr), FLUSH);
2061                 spin_unlock_irqrestore(&adapter->bit64reglock.lock,
2062                                         adapter->bit64reglock.flags);
2063
2064                 slic_config_get(adapter, phys_configl, phys_configh);
2065
2066                 for (;;) {
2067                         if (adapter->pshmem->isr) {
2068                                 if (adapter->pshmem->isr & ISR_UPC) {
2069                                         adapter->pshmem->isr = 0;
2070                                         slic_reg64_write(adapter,
2071                                                 &slic_regs->slic_isp, 0,
2072                                                 &slic_regs->slic_addr_upper,
2073                                                 0, FLUSH);
2074                                         slic_reg32_write(&slic_regs->slic_isr,
2075                                                          0, FLUSH);
2076
2077                                         slic_upr_request_complete(adapter, 0);
2078                                         break;
2079                                 } else {
2080                                         adapter->pshmem->isr = 0;
2081                                         slic_reg32_write(&slic_regs->slic_isr,
2082                                                          0, FLUSH);
2083                                 }
2084                         } else {
2085                                 mdelay(1);
2086                                 i++;
2087                                 if (i > 5000) {
2088                                         dev_err(&adapter->pcidev->dev,
2089                                                 "%d config data fetch timed out!\n",
2090                                                 adapter->port);
2091                                         slic_reg64_write(adapter,
2092                                                 &slic_regs->slic_isp, 0,
2093                                                 &slic_regs->slic_addr_upper,
2094                                                 0, FLUSH);
2095                                         return -EINVAL;
2096                                 }
2097                         }
2098                 }
2099
2100                 switch (adapter->devid) {
2101                 /* Oasis card */
2102                 case SLIC_2GB_DEVICE_ID:
2103                         /* extract EEPROM data and pointers to EEPROM data */
2104                         pOeeprom = (struct oslic_eeprom *) peeprom;
2105                         eecodesize = pOeeprom->EecodeSize;
2106                         dramsize = pOeeprom->DramSize;
2107                         pmac = pOeeprom->MacInfo;
2108                         fruformat = pOeeprom->FruFormat;
2109                         patkfru = &pOeeprom->AtkFru;
2110                         oemfruformat = pOeeprom->OemFruFormat;
2111                         poemfru = &pOeeprom->OemFru;
2112                         macaddrs = 2;
2113                         /* Minor kludge for Oasis card
2114                              get 2 MAC addresses from the
2115                              EEPROM to ensure that function 1
2116                              gets the Port 1 MAC address */
2117                         break;
2118                 default:
2119                         /* extract EEPROM data and pointers to EEPROM data */
2120                         eecodesize = peeprom->EecodeSize;
2121                         dramsize = peeprom->DramSize;
2122                         pmac = peeprom->u2.mac.MacInfo;
2123                         fruformat = peeprom->FruFormat;
2124                         patkfru = &peeprom->AtkFru;
2125                         oemfruformat = peeprom->OemFruFormat;
2126                         poemfru = &peeprom->OemFru;
2127                         break;
2128                 }
2129
2130                 card->config.EepromValid = false;
2131
2132                 /*  see if the EEPROM is valid by checking it's checksum */
2133                 if ((eecodesize <= MAX_EECODE_SIZE) &&
2134                     (eecodesize >= MIN_EECODE_SIZE)) {
2135
2136                         ee_chksum =
2137                             *(u16 *) ((char *) peeprom + (eecodesize - 2));
2138                         /*
2139                             calculate the EEPROM checksum
2140                         */
2141                         calc_chksum =
2142                             ~slic_eeprom_cksum((char *) peeprom,
2143                                                (eecodesize - 2));
2144                         /*
2145                             if the ucdoe chksum flag bit worked,
2146                             we wouldn't need this shit
2147                         */
2148                         if (ee_chksum == calc_chksum)
2149                                 card->config.EepromValid = true;
2150                 }
2151                 /*  copy in the DRAM size */
2152                 card->config.DramSize = dramsize;
2153
2154                 /*  copy in the MAC address(es) */
2155                 for (i = 0; i < macaddrs; i++) {
2156                         memcpy(&card->config.MacInfo[i],
2157                                &pmac[i], sizeof(struct slic_config_mac));
2158                 }
2159
2160                 /*  copy the Alacritech FRU information */
2161                 card->config.FruFormat = fruformat;
2162                 memcpy(&card->config.AtkFru, patkfru,
2163                                                 sizeof(struct atk_fru));
2164
2165                 pci_free_consistent(adapter->pcidev,
2166                                     sizeof(struct slic_eeprom),
2167                                     peeprom, phys_config);
2168
2169                 if ((!card->config.EepromValid) &&
2170                     (adapter->reg_params.fail_on_bad_eeprom)) {
2171                         slic_reg64_write(adapter, &slic_regs->slic_isp, 0,
2172                                          &slic_regs->slic_addr_upper,
2173                                          0, FLUSH);
2174                         dev_err(&adapter->pcidev->dev,
2175                                 "unsupported CONFIGURATION EEPROM invalid\n");
2176                         return -EINVAL;
2177                 }
2178
2179                 card->config_set = 1;
2180         }
2181
2182         if (slic_card_download_gbrcv(adapter)) {
2183                 dev_err(&adapter->pcidev->dev,
2184                         "unable to download GB receive microcode\n");
2185                 return -EINVAL;
2186         }
2187
2188         if (slic_global.dynamic_intagg)
2189                 slic_intagg_set(adapter, 0);
2190         else
2191                 slic_intagg_set(adapter, intagg_delay);
2192
2193         /*
2194          *  Initialize ping status to "ok"
2195          */
2196         card->pingstatus = ISR_PINGMASK;
2197
2198         /*
2199          * Lastly, mark our card state as up and return success
2200          */
2201         card->state = CARD_UP;
2202         card->reset_in_progress = 0;
2203
2204         return STATUS_SUCCESS;
2205 }
2206
2207 static u32 slic_card_locate(struct adapter *adapter)
2208 {
2209         struct sliccard *card = slic_global.slic_card;
2210         struct physcard *physcard = slic_global.phys_card;
2211         ushort card_hostid;
2212         u16 __iomem *hostid_reg;
2213         uint i;
2214         uint rdhostid_offset = 0;
2215
2216         switch (adapter->devid) {
2217         case SLIC_2GB_DEVICE_ID:
2218                 rdhostid_offset = SLIC_RDHOSTID_2GB;
2219                 break;
2220         case SLIC_1GB_DEVICE_ID:
2221                 rdhostid_offset = SLIC_RDHOSTID_1GB;
2222                 break;
2223         default:
2224                 ASSERT(0);
2225                 break;
2226         }
2227
2228         hostid_reg =
2229             (u16 __iomem *) (((u8 __iomem *) (adapter->slic_regs)) +
2230             rdhostid_offset);
2231
2232         /* read the 16 bit hostid from SRAM */
2233         card_hostid = (ushort) readw(hostid_reg);
2234
2235         /* Initialize a new card structure if need be */
2236         if (card_hostid == SLIC_HOSTID_DEFAULT) {
2237                 card = kzalloc(sizeof(struct sliccard), GFP_KERNEL);
2238                 if (card == NULL)
2239                         return -ENOMEM;
2240
2241                 card->next = slic_global.slic_card;
2242                 slic_global.slic_card = card;
2243                 card->busnumber = adapter->busnumber;
2244                 card->slotnumber = adapter->slotnumber;
2245
2246                 /* Find an available cardnum */
2247                 for (i = 0; i < SLIC_MAX_CARDS; i++) {
2248                         if (slic_global.cardnuminuse[i] == 0) {
2249                                 slic_global.cardnuminuse[i] = 1;
2250                                 card->cardnum = i;
2251                                 break;
2252                         }
2253                 }
2254                 slic_global.num_slic_cards++;
2255
2256                 slic_debug_card_create(card);
2257         } else {
2258                 /* Card exists, find the card this adapter belongs to */
2259                 while (card) {
2260                         if (card->cardnum == card_hostid)
2261                                 break;
2262                         card = card->next;
2263                 }
2264         }
2265
2266         ASSERT(card);
2267         if (!card)
2268                 return STATUS_FAILURE;
2269         /* Put the adapter in the card's adapter list */
2270         ASSERT(card->adapter[adapter->port] == NULL);
2271         if (!card->adapter[adapter->port]) {
2272                 card->adapter[adapter->port] = adapter;
2273                 adapter->card = card;
2274         }
2275
2276         card->card_size = 1;    /* one port per *logical* card */
2277
2278         while (physcard) {
2279                 for (i = 0; i < SLIC_MAX_PORTS; i++) {
2280                         if (!physcard->adapter[i])
2281                                 continue;
2282                         else
2283                                 break;
2284                 }
2285                 ASSERT(i != SLIC_MAX_PORTS);
2286                 if (physcard->adapter[i]->slotnumber == adapter->slotnumber)
2287                         break;
2288                 physcard = physcard->next;
2289         }
2290         if (!physcard) {
2291                 /* no structure allocated for this physical card yet */
2292                 physcard = kzalloc(sizeof(struct physcard), GFP_ATOMIC);
2293                 ASSERT(physcard);
2294
2295                 physcard->next = slic_global.phys_card;
2296                 slic_global.phys_card = physcard;
2297                 physcard->adapters_allocd = 1;
2298         } else {
2299                 physcard->adapters_allocd++;
2300         }
2301         /* Note - this is ZERO relative */
2302         adapter->physport = physcard->adapters_allocd - 1;
2303
2304         ASSERT(physcard->adapter[adapter->physport] == NULL);
2305         physcard->adapter[adapter->physport] = adapter;
2306         adapter->physcard = physcard;
2307
2308         return 0;
2309 }
2310
2311 static void slic_soft_reset(struct adapter *adapter)
2312 {
2313         if (adapter->card->state == CARD_UP) {
2314                 slic_reg32_write(&adapter->slic_regs->slic_quiesce, 0, FLUSH);
2315                 mdelay(1);
2316         }
2317
2318         slic_reg32_write(&adapter->slic_regs->slic_reset, SLIC_RESET_MAGIC,
2319                          FLUSH);
2320         mdelay(1);
2321 }
2322
2323 static void slic_config_set(struct adapter *adapter, bool linkchange)
2324 {
2325         u32 value;
2326         u32 RcrReset;
2327         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2328
2329         if (linkchange) {
2330                 /* Setup MAC */
2331                 slic_mac_config(adapter);
2332                 RcrReset = GRCR_RESET;
2333         } else {
2334                 slic_mac_address_config(adapter);
2335                 RcrReset = 0;
2336         }
2337
2338         if (adapter->linkduplex == LINK_FULLD) {
2339                 /* setup xmtcfg */
2340                 value = (GXCR_RESET |   /* Always reset     */
2341                          GXCR_XMTEN |   /* Enable transmit  */
2342                          GXCR_PAUSEEN); /* Enable pause     */
2343
2344                 slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH);
2345
2346                 /* Setup rcvcfg last */
2347                 value = (RcrReset |     /* Reset, if linkchange */
2348                          GRCR_CTLEN |   /* Enable CTL frames    */
2349                          GRCR_ADDRAEN | /* Address A enable     */
2350                          GRCR_RCVBAD |  /* Rcv bad frames       */
2351                          (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT));
2352         } else {
2353                 /* setup xmtcfg */
2354                 value = (GXCR_RESET |   /* Always reset     */
2355                          GXCR_XMTEN);   /* Enable transmit  */
2356
2357                 slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH);
2358
2359                 /* Setup rcvcfg last */
2360                 value = (RcrReset |     /* Reset, if linkchange */
2361                          GRCR_ADDRAEN | /* Address A enable     */
2362                          GRCR_RCVBAD |  /* Rcv bad frames       */
2363                          (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT));
2364         }
2365
2366         if (adapter->state != ADAPT_DOWN) {
2367                 /* Only enable receive if we are restarting or running */
2368                 value |= GRCR_RCVEN;
2369         }
2370
2371         if (adapter->macopts & MAC_PROMISC)
2372                 value |= GRCR_RCVALL;
2373
2374         slic_reg32_write(&slic_regs->slic_wrcfg, value, FLUSH);
2375 }
2376
2377 /*
2378  *  Turn off RCV and XMT, power down PHY
2379  */
2380 static void slic_config_clear(struct adapter *adapter)
2381 {
2382         u32 value;
2383         u32 phy_config;
2384         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2385
2386         /* Setup xmtcfg */
2387         value = (GXCR_RESET |   /* Always reset */
2388                  GXCR_PAUSEEN); /* Enable pause */
2389
2390         slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH);
2391
2392         value = (GRCR_RESET |   /* Always reset      */
2393                  GRCR_CTLEN |   /* Enable CTL frames */
2394                  GRCR_ADDRAEN | /* Address A enable  */
2395                  (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT));
2396
2397         slic_reg32_write(&slic_regs->slic_wrcfg, value, FLUSH);
2398
2399         /* power down phy */
2400         phy_config = (MIICR_REG_PCR | (PCR_POWERDOWN));
2401         slic_reg32_write(&slic_regs->slic_wphy, phy_config, FLUSH);
2402 }
2403
2404 static void slic_config_get(struct adapter *adapter, u32 config,
2405                                                         u32 config_h)
2406 {
2407         int status;
2408
2409         status = slic_upr_request(adapter,
2410                                   SLIC_UPR_RCONFIG,
2411                                   (u32) config, (u32) config_h, 0, 0);
2412         ASSERT(status == 0);
2413 }
2414
2415 static void slic_mac_address_config(struct adapter *adapter)
2416 {
2417         u32 value;
2418         u32 value2;
2419         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2420
2421         value = *(u32 *) &adapter->currmacaddr[2];
2422         value = ntohl(value);
2423         slic_reg32_write(&slic_regs->slic_wraddral, value, FLUSH);
2424         slic_reg32_write(&slic_regs->slic_wraddrbl, value, FLUSH);
2425
2426         value2 = (u32) ((adapter->currmacaddr[0] << 8 |
2427                              adapter->currmacaddr[1]) & 0xFFFF);
2428
2429         slic_reg32_write(&slic_regs->slic_wraddrah, value2, FLUSH);
2430         slic_reg32_write(&slic_regs->slic_wraddrbh, value2, FLUSH);
2431
2432         /* Write our multicast mask out to the card.  This is done */
2433         /* here in addition to the slic_mcast_addr_set routine     */
2434         /* because ALL_MCAST may have been enabled or disabled     */
2435         slic_mcast_set_mask(adapter);
2436 }
2437
2438 static void slic_mac_config(struct adapter *adapter)
2439 {
2440         u32 value;
2441         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2442
2443         /* Setup GMAC gaps */
2444         if (adapter->linkspeed == LINK_1000MB) {
2445                 value = ((GMCR_GAPBB_1000 << GMCR_GAPBB_SHIFT) |
2446                          (GMCR_GAPR1_1000 << GMCR_GAPR1_SHIFT) |
2447                          (GMCR_GAPR2_1000 << GMCR_GAPR2_SHIFT));
2448         } else {
2449                 value = ((GMCR_GAPBB_100 << GMCR_GAPBB_SHIFT) |
2450                          (GMCR_GAPR1_100 << GMCR_GAPR1_SHIFT) |
2451                          (GMCR_GAPR2_100 << GMCR_GAPR2_SHIFT));
2452         }
2453
2454         /* enable GMII */
2455         if (adapter->linkspeed == LINK_1000MB)
2456                 value |= GMCR_GBIT;
2457
2458         /* enable fullduplex */
2459         if ((adapter->linkduplex == LINK_FULLD)
2460             || (adapter->macopts & MAC_LOOPBACK)) {
2461                 value |= GMCR_FULLD;
2462         }
2463
2464         /* write mac config */
2465         slic_reg32_write(&slic_regs->slic_wmcfg, value, FLUSH);
2466
2467         /* setup mac addresses */
2468         slic_mac_address_config(adapter);
2469 }
2470
2471 static bool slic_mac_filter(struct adapter *adapter,
2472                         struct ether_header *ether_frame)
2473 {
2474         u32 opts = adapter->macopts;
2475         u32 *dhost4 = (u32 *)&ether_frame->ether_dhost[0];
2476         u16 *dhost2 = (u16 *)&ether_frame->ether_dhost[4];
2477         bool equaladdr;
2478
2479         if (opts & MAC_PROMISC)
2480                 return true;
2481
2482         if ((*dhost4 == 0xFFFFFFFF) && (*dhost2 == 0xFFFF)) {
2483                 if (opts & MAC_BCAST) {
2484                         adapter->rcv_broadcasts++;
2485                         return true;
2486                 } else {
2487                         return false;
2488                 }
2489         }
2490
2491         if (ether_frame->ether_dhost[0] & 0x01) {
2492                 if (opts & MAC_ALLMCAST) {
2493                         adapter->rcv_multicasts++;
2494                         adapter->stats.multicast++;
2495                         return true;
2496                 }
2497                 if (opts & MAC_MCAST) {
2498                         struct mcast_address *mcaddr = adapter->mcastaddrs;
2499
2500                         while (mcaddr) {
2501                                 ETHER_EQ_ADDR(mcaddr->address,
2502                                               ether_frame->ether_dhost,
2503                                               equaladdr);
2504                                 if (equaladdr) {
2505                                         adapter->rcv_multicasts++;
2506                                         adapter->stats.multicast++;
2507                                         return true;
2508                                 }
2509                                 mcaddr = mcaddr->next;
2510                         }
2511                         return false;
2512                 } else {
2513                         return false;
2514                 }
2515         }
2516         if (opts & MAC_DIRECTED) {
2517                 adapter->rcv_unicasts++;
2518                 return true;
2519         }
2520         return false;
2521
2522 }
2523
2524 static int slic_mac_set_address(struct net_device *dev, void *ptr)
2525 {
2526         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
2527         struct sockaddr *addr = ptr;
2528
2529         if (netif_running(dev))
2530                 return -EBUSY;
2531         if (!adapter)
2532                 return -EBUSY;
2533
2534         if (!is_valid_ether_addr(addr->sa_data))
2535                 return -EINVAL;
2536
2537         memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
2538         memcpy(adapter->currmacaddr, addr->sa_data, dev->addr_len);
2539
2540         slic_config_set(adapter, true);
2541         return 0;
2542 }
2543
2544 static void slic_timer_load_check(ulong cardaddr)
2545 {
2546         struct sliccard *card = (struct sliccard *)cardaddr;
2547         struct adapter *adapter = card->master;
2548         u32 __iomem *intagg;
2549         u32 load = card->events;
2550         u32 level = 0;
2551
2552         intagg = &adapter->slic_regs->slic_intagg;
2553
2554         if ((adapter) && (adapter->state == ADAPT_UP) &&
2555             (card->state == CARD_UP) && (slic_global.dynamic_intagg)) {
2556                 if (adapter->devid == SLIC_1GB_DEVICE_ID) {
2557                         if (adapter->linkspeed == LINK_1000MB)
2558                                 level = 100;
2559                         else {
2560                                 if (load > SLIC_LOAD_5)
2561                                         level = SLIC_INTAGG_5;
2562                                 else if (load > SLIC_LOAD_4)
2563                                         level = SLIC_INTAGG_4;
2564                                 else if (load > SLIC_LOAD_3)
2565                                         level = SLIC_INTAGG_3;
2566                                 else if (load > SLIC_LOAD_2)
2567                                         level = SLIC_INTAGG_2;
2568                                 else if (load > SLIC_LOAD_1)
2569                                         level = SLIC_INTAGG_1;
2570                                 else
2571                                         level = SLIC_INTAGG_0;
2572                         }
2573                         if (card->loadlevel_current != level) {
2574                                 card->loadlevel_current = level;
2575                                 slic_reg32_write(intagg, level, FLUSH);
2576                         }
2577                 } else {
2578                         if (load > SLIC_LOAD_5)
2579                                 level = SLIC_INTAGG_5;
2580                         else if (load > SLIC_LOAD_4)
2581                                 level = SLIC_INTAGG_4;
2582                         else if (load > SLIC_LOAD_3)
2583                                 level = SLIC_INTAGG_3;
2584                         else if (load > SLIC_LOAD_2)
2585                                 level = SLIC_INTAGG_2;
2586                         else if (load > SLIC_LOAD_1)
2587                                 level = SLIC_INTAGG_1;
2588                         else
2589                                 level = SLIC_INTAGG_0;
2590                         if (card->loadlevel_current != level) {
2591                                 card->loadlevel_current = level;
2592                                 slic_reg32_write(intagg, level, FLUSH);
2593                         }
2594                 }
2595         }
2596         card->events = 0;
2597         card->loadtimer.expires = jiffies + (SLIC_LOADTIMER_PERIOD * HZ);
2598         add_timer(&card->loadtimer);
2599 }
2600
2601 static void slic_assert_fail(void)
2602 {
2603         u32 cpuid;
2604         u32 curr_pid;
2605         cpuid = smp_processor_id();
2606         curr_pid = current->pid;
2607
2608         printk(KERN_ERR "%s CPU # %d ---- PID # %d\n",
2609                __func__, cpuid, curr_pid);
2610 }
2611
2612 static int slic_upr_queue_request(struct adapter *adapter,
2613                            u32 upr_request,
2614                            u32 upr_data,
2615                            u32 upr_data_h,
2616                            u32 upr_buffer, u32 upr_buffer_h)
2617 {
2618         struct slic_upr *upr;
2619         struct slic_upr *uprqueue;
2620
2621         upr = kmalloc(sizeof(struct slic_upr), GFP_ATOMIC);
2622         if (!upr)
2623                 return -ENOMEM;
2624
2625         upr->adapter = adapter->port;
2626         upr->upr_request = upr_request;
2627         upr->upr_data = upr_data;
2628         upr->upr_buffer = upr_buffer;
2629         upr->upr_data_h = upr_data_h;
2630         upr->upr_buffer_h = upr_buffer_h;
2631         upr->next = NULL;
2632         if (adapter->upr_list) {
2633                 uprqueue = adapter->upr_list;
2634
2635                 while (uprqueue->next)
2636                         uprqueue = uprqueue->next;
2637                 uprqueue->next = upr;
2638         } else {
2639                 adapter->upr_list = upr;
2640         }
2641         return STATUS_SUCCESS;
2642 }
2643
2644 static int slic_upr_request(struct adapter *adapter,
2645                      u32 upr_request,
2646                      u32 upr_data,
2647                      u32 upr_data_h,
2648                      u32 upr_buffer, u32 upr_buffer_h)
2649 {
2650         int status;
2651
2652         spin_lock_irqsave(&adapter->upr_lock.lock, adapter->upr_lock.flags);
2653         status = slic_upr_queue_request(adapter,
2654                                         upr_request,
2655                                         upr_data,
2656                                         upr_data_h, upr_buffer, upr_buffer_h);
2657         if (status != STATUS_SUCCESS) {
2658                 spin_unlock_irqrestore(&adapter->upr_lock.lock,
2659                                         adapter->upr_lock.flags);
2660                 return status;
2661         }
2662         slic_upr_start(adapter);
2663         spin_unlock_irqrestore(&adapter->upr_lock.lock,
2664                                 adapter->upr_lock.flags);
2665         return STATUS_PENDING;
2666 }
2667
2668 static void slic_upr_request_complete(struct adapter *adapter, u32 isr)
2669 {
2670         struct sliccard *card = adapter->card;
2671         struct slic_upr *upr;
2672
2673         spin_lock_irqsave(&adapter->upr_lock.lock, adapter->upr_lock.flags);
2674         upr = adapter->upr_list;
2675         if (!upr) {
2676                 ASSERT(0);
2677                 spin_unlock_irqrestore(&adapter->upr_lock.lock,
2678                                         adapter->upr_lock.flags);
2679                 return;
2680         }
2681         adapter->upr_list = upr->next;
2682         upr->next = NULL;
2683         adapter->upr_busy = 0;
2684         ASSERT(adapter->port == upr->adapter);
2685         switch (upr->upr_request) {
2686         case SLIC_UPR_STATS:
2687                 {
2688                         struct slic_stats *slicstats =
2689                             (struct slic_stats *) &adapter->pshmem->inicstats;
2690                         struct slic_stats *newstats = slicstats;
2691                         struct slic_stats  *old = &adapter->inicstats_prev;
2692                         struct slicnet_stats *stst = &adapter->slic_stats;
2693
2694                         if (isr & ISR_UPCERR) {
2695                                 dev_err(&adapter->netdev->dev,
2696                                         "SLIC_UPR_STATS command failed isr[%x]\n",
2697                                         isr);
2698
2699                                 break;
2700                         }
2701                         UPDATE_STATS_GB(stst->tcp.xmit_tcp_segs,
2702                                         newstats->xmit_tcp_segs_gb,
2703                                         old->xmit_tcp_segs_gb);
2704
2705                         UPDATE_STATS_GB(stst->tcp.xmit_tcp_bytes,
2706                                         newstats->xmit_tcp_bytes_gb,
2707                                         old->xmit_tcp_bytes_gb);
2708
2709                         UPDATE_STATS_GB(stst->tcp.rcv_tcp_segs,
2710                                         newstats->rcv_tcp_segs_gb,
2711                                         old->rcv_tcp_segs_gb);
2712
2713                         UPDATE_STATS_GB(stst->tcp.rcv_tcp_bytes,
2714                                         newstats->rcv_tcp_bytes_gb,
2715                                         old->rcv_tcp_bytes_gb);
2716
2717                         UPDATE_STATS_GB(stst->iface.xmt_bytes,
2718                                         newstats->xmit_bytes_gb,
2719                                         old->xmit_bytes_gb);
2720
2721                         UPDATE_STATS_GB(stst->iface.xmt_ucast,
2722                                         newstats->xmit_unicasts_gb,
2723                                         old->xmit_unicasts_gb);
2724
2725                         UPDATE_STATS_GB(stst->iface.rcv_bytes,
2726                                         newstats->rcv_bytes_gb,
2727                                         old->rcv_bytes_gb);
2728
2729                         UPDATE_STATS_GB(stst->iface.rcv_ucast,
2730                                         newstats->rcv_unicasts_gb,
2731                                         old->rcv_unicasts_gb);
2732
2733                         UPDATE_STATS_GB(stst->iface.xmt_errors,
2734                                         newstats->xmit_collisions_gb,
2735                                         old->xmit_collisions_gb);
2736
2737                         UPDATE_STATS_GB(stst->iface.xmt_errors,
2738                                         newstats->xmit_excess_collisions_gb,
2739                                         old->xmit_excess_collisions_gb);
2740
2741                         UPDATE_STATS_GB(stst->iface.xmt_errors,
2742                                         newstats->xmit_other_error_gb,
2743                                         old->xmit_other_error_gb);
2744
2745                         UPDATE_STATS_GB(stst->iface.rcv_errors,
2746                                         newstats->rcv_other_error_gb,
2747                                         old->rcv_other_error_gb);
2748
2749                         UPDATE_STATS_GB(stst->iface.rcv_discards,
2750                                         newstats->rcv_drops_gb,
2751                                         old->rcv_drops_gb);
2752
2753                         if (newstats->rcv_drops_gb > old->rcv_drops_gb) {
2754                                 adapter->rcv_drops +=
2755                                     (newstats->rcv_drops_gb -
2756                                      old->rcv_drops_gb);
2757                         }
2758                         memcpy(old, newstats, sizeof(struct slic_stats));
2759                         break;
2760                 }
2761         case SLIC_UPR_RLSR:
2762                 slic_link_upr_complete(adapter, isr);
2763                 break;
2764         case SLIC_UPR_RCONFIG:
2765                 break;
2766         case SLIC_UPR_RPHY:
2767                 ASSERT(0);
2768                 break;
2769         case SLIC_UPR_ENLB:
2770                 ASSERT(0);
2771                 break;
2772         case SLIC_UPR_ENCT:
2773                 ASSERT(0);
2774                 break;
2775         case SLIC_UPR_PDWN:
2776                 ASSERT(0);
2777                 break;
2778         case SLIC_UPR_PING:
2779                 card->pingstatus |= (isr & ISR_PINGDSMASK);
2780                 break;
2781         default:
2782                 ASSERT(0);
2783         }
2784         kfree(upr);
2785         slic_upr_start(adapter);
2786         spin_unlock_irqrestore(&adapter->upr_lock.lock,
2787                                 adapter->upr_lock.flags);
2788 }
2789
2790 static void slic_upr_start(struct adapter *adapter)
2791 {
2792         struct slic_upr *upr;
2793         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2794 /*
2795     char * ptr1;
2796     char * ptr2;
2797     uint cmdoffset;
2798 */
2799         upr = adapter->upr_list;
2800         if (!upr)
2801                 return;
2802         if (adapter->upr_busy)
2803                 return;
2804         adapter->upr_busy = 1;
2805
2806         switch (upr->upr_request) {
2807         case SLIC_UPR_STATS:
2808                 if (upr->upr_data_h == 0) {
2809                         slic_reg32_write(&slic_regs->slic_stats, upr->upr_data,
2810                                          FLUSH);
2811                 } else {
2812                         slic_reg64_write(adapter, &slic_regs->slic_stats64,
2813                                          upr->upr_data,
2814                                          &slic_regs->slic_addr_upper,
2815                                          upr->upr_data_h, FLUSH);
2816                 }
2817                 break;
2818
2819         case SLIC_UPR_RLSR:
2820                 slic_reg64_write(adapter, &slic_regs->slic_rlsr, upr->upr_data,
2821                                  &slic_regs->slic_addr_upper, upr->upr_data_h,
2822                                  FLUSH);
2823                 break;
2824
2825         case SLIC_UPR_RCONFIG:
2826                 slic_reg64_write(adapter, &slic_regs->slic_rconfig,
2827                                  upr->upr_data, &slic_regs->slic_addr_upper,
2828                                  upr->upr_data_h, FLUSH);
2829                 break;
2830         case SLIC_UPR_PING:
2831                 slic_reg32_write(&slic_regs->slic_ping, 1, FLUSH);
2832                 break;
2833         default:
2834                 ASSERT(0);
2835         }
2836 }
2837
2838 static void slic_link_upr_complete(struct adapter *adapter, u32 isr)
2839 {
2840         u32 linkstatus = adapter->pshmem->linkstatus;
2841         uint linkup;
2842         unsigned char linkspeed;
2843         unsigned char linkduplex;
2844
2845         if ((isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) {
2846                 struct slic_shmem *pshmem;
2847
2848                 pshmem = (struct slic_shmem *)adapter->phys_shmem;
2849 #if defined(CONFIG_X86_64)
2850                 slic_upr_queue_request(adapter,
2851                                        SLIC_UPR_RLSR,
2852                                        SLIC_GET_ADDR_LOW(&pshmem->linkstatus),
2853                                        SLIC_GET_ADDR_HIGH(&pshmem->linkstatus),
2854                                        0, 0);
2855 #elif defined(CONFIG_X86)
2856                 slic_upr_queue_request(adapter,
2857                                        SLIC_UPR_RLSR,
2858                                        (u32) &pshmem->linkstatus,
2859                                        SLIC_GET_ADDR_HIGH(pshmem), 0, 0);
2860 #else
2861                 Stop Compilation;
2862 #endif
2863                 return;
2864         }
2865         if (adapter->state != ADAPT_UP)
2866                 return;
2867
2868         ASSERT((adapter->devid == SLIC_1GB_DEVICE_ID)
2869                || (adapter->devid == SLIC_2GB_DEVICE_ID));
2870
2871         linkup = linkstatus & GIG_LINKUP ? LINK_UP : LINK_DOWN;
2872         if (linkstatus & GIG_SPEED_1000)
2873                 linkspeed = LINK_1000MB;
2874         else if (linkstatus & GIG_SPEED_100)
2875                 linkspeed = LINK_100MB;
2876         else
2877                 linkspeed = LINK_10MB;
2878
2879         if (linkstatus & GIG_FULLDUPLEX)
2880                 linkduplex = LINK_FULLD;
2881         else
2882                 linkduplex = LINK_HALFD;
2883
2884         if ((adapter->linkstate == LINK_DOWN) && (linkup == LINK_DOWN))
2885                 return;
2886
2887         /* link up event, but nothing has changed */
2888         if ((adapter->linkstate == LINK_UP) &&
2889             (linkup == LINK_UP) &&
2890             (adapter->linkspeed == linkspeed) &&
2891             (adapter->linkduplex == linkduplex))
2892                 return;
2893
2894         /* link has changed at this point */
2895
2896         /* link has gone from up to down */
2897         if (linkup == LINK_DOWN) {
2898                 adapter->linkstate = LINK_DOWN;
2899                 return;
2900         }
2901
2902         /* link has gone from down to up */
2903         adapter->linkspeed = linkspeed;
2904         adapter->linkduplex = linkduplex;
2905
2906         if (adapter->linkstate != LINK_UP) {
2907                 /* setup the mac */
2908                 slic_config_set(adapter, true);
2909                 adapter->linkstate = LINK_UP;
2910                 netif_start_queue(adapter->netdev);
2911         }
2912 }
2913
2914 /*
2915  *  this is here to checksum the eeprom, there is some ucode bug
2916  *  which prevens us from using the ucode result.
2917  *  remove this once ucode is fixed.
2918  */
2919 static ushort slic_eeprom_cksum(char *m, int len)
2920 {
2921 #define ADDCARRY(x)  (x > 65535 ? x -= 65535 : x)
2922 #define REDUCE {l_util.l = sum; sum = l_util.s[0] + l_util.s[1]; ADDCARRY(sum);\
2923                 }
2924
2925         u16 *w;
2926         u32 sum = 0;
2927         u32 byte_swapped = 0;
2928         u32 w_int;
2929
2930         union {
2931                 char c[2];
2932                 ushort s;
2933         } s_util;
2934
2935         union {
2936                 ushort s[2];
2937                 int l;
2938         } l_util;
2939
2940         l_util.l = 0;
2941         s_util.s = 0;
2942
2943         w = (u16 *)m;
2944 #ifdef CONFIG_X86_64
2945         w_int = (u32) ((ulong) w & 0x00000000FFFFFFFF);
2946 #else
2947         w_int = (u32) (w);
2948 #endif
2949         if ((1 & w_int) && (len > 0)) {
2950                 REDUCE;
2951                 sum <<= 8;
2952                 s_util.c[0] = *(unsigned char *)w;
2953                 w = (u16 *)((char *)w + 1);
2954                 len--;
2955                 byte_swapped = 1;
2956         }
2957
2958         /* Unroll the loop to make overhead from branches &c small. */
2959         while ((len -= 32) >= 0) {
2960                 sum += w[0];
2961                 sum += w[1];
2962                 sum += w[2];
2963                 sum += w[3];
2964                 sum += w[4];
2965                 sum += w[5];
2966                 sum += w[6];
2967                 sum += w[7];
2968                 sum += w[8];
2969                 sum += w[9];
2970                 sum += w[10];
2971                 sum += w[11];
2972                 sum += w[12];
2973                 sum += w[13];
2974                 sum += w[14];
2975                 sum += w[15];
2976                 w = (u16 *)((ulong) w + 16);    /* verify */
2977         }
2978         len += 32;
2979         while ((len -= 8) >= 0) {
2980                 sum += w[0];
2981                 sum += w[1];
2982                 sum += w[2];
2983                 sum += w[3];
2984                 w = (u16 *)((ulong) w + 4);     /* verify */
2985         }
2986         len += 8;
2987         if (len != 0 || byte_swapped != 0) {
2988                 REDUCE;
2989                 while ((len -= 2) >= 0)
2990                         sum += *w++;    /* verify */
2991                 if (byte_swapped) {
2992                         REDUCE;
2993                         sum <<= 8;
2994                         byte_swapped = 0;
2995                         if (len == -1) {
2996                                 s_util.c[1] = *(char *) w;
2997                                 sum += s_util.s;
2998                                 len = 0;
2999                         } else {
3000                                 len = -1;
3001                         }
3002
3003                 } else if (len == -1) {
3004                         s_util.c[0] = *(char *) w;
3005                 }
3006
3007                 if (len == -1) {
3008                         s_util.c[1] = 0;
3009                         sum += s_util.s;
3010                 }
3011         }
3012         REDUCE;
3013         return (ushort) sum;
3014 }
3015
3016 static int slic_rspqueue_init(struct adapter *adapter)
3017 {
3018         int i;
3019         struct slic_rspqueue *rspq = &adapter->rspqueue;
3020         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
3021         u32 paddrh = 0;
3022
3023         ASSERT(adapter->state == ADAPT_DOWN);
3024         memset(rspq, 0, sizeof(struct slic_rspqueue));
3025
3026         rspq->num_pages = SLIC_RSPQ_PAGES_GB;
3027
3028         for (i = 0; i < rspq->num_pages; i++) {
3029                 rspq->vaddr[i] = pci_alloc_consistent(adapter->pcidev,
3030                                                       PAGE_SIZE,
3031                                                       &rspq->paddr[i]);
3032                 if (!rspq->vaddr[i]) {
3033                         dev_err(&adapter->pcidev->dev,
3034                                 "pci_alloc_consistent failed\n");
3035                         slic_rspqueue_free(adapter);
3036                         return STATUS_FAILURE;
3037                 }
3038 #ifndef CONFIG_X86_64
3039                 ASSERT(((u32) rspq->vaddr[i] & 0xFFFFF000) ==
3040                        (u32) rspq->vaddr[i]);
3041                 ASSERT(((u32) rspq->paddr[i] & 0xFFFFF000) ==
3042                        (u32) rspq->paddr[i]);
3043 #endif
3044                 memset(rspq->vaddr[i], 0, PAGE_SIZE);
3045
3046                 if (paddrh == 0) {
3047                         slic_reg32_write(&slic_regs->slic_rbar,
3048                                 (rspq->paddr[i] | SLIC_RSPQ_BUFSINPAGE),
3049                                 DONT_FLUSH);
3050                 } else {
3051                         slic_reg64_write(adapter, &slic_regs->slic_rbar64,
3052                                 (rspq->paddr[i] | SLIC_RSPQ_BUFSINPAGE),
3053                                 &slic_regs->slic_addr_upper,
3054                                 paddrh, DONT_FLUSH);
3055                 }
3056         }
3057         rspq->offset = 0;
3058         rspq->pageindex = 0;
3059         rspq->rspbuf = (struct slic_rspbuf *)rspq->vaddr[0];
3060         return STATUS_SUCCESS;
3061 }
3062
3063 static void slic_rspqueue_free(struct adapter *adapter)
3064 {
3065         int i;
3066         struct slic_rspqueue *rspq = &adapter->rspqueue;
3067
3068         for (i = 0; i < rspq->num_pages; i++) {
3069                 if (rspq->vaddr[i]) {
3070                         pci_free_consistent(adapter->pcidev, PAGE_SIZE,
3071                                             rspq->vaddr[i], rspq->paddr[i]);
3072                 }
3073                 rspq->vaddr[i] = NULL;
3074                 rspq->paddr[i] = 0;
3075         }
3076         rspq->offset = 0;
3077         rspq->pageindex = 0;
3078         rspq->rspbuf = NULL;
3079 }
3080
3081 static struct slic_rspbuf *slic_rspqueue_getnext(struct adapter *adapter)
3082 {
3083         struct slic_rspqueue *rspq = &adapter->rspqueue;
3084         struct slic_rspbuf *buf;
3085
3086         if (!(rspq->rspbuf->status))
3087                 return NULL;
3088
3089         buf = rspq->rspbuf;
3090 #ifndef CONFIG_X86_64
3091         ASSERT((buf->status & 0xFFFFFFE0) == 0);
3092 #endif
3093         ASSERT(buf->hosthandle);
3094         if (++rspq->offset < SLIC_RSPQ_BUFSINPAGE) {
3095                 rspq->rspbuf++;
3096 #ifndef CONFIG_X86_64
3097                 ASSERT(((u32) rspq->rspbuf & 0xFFFFFFE0) ==
3098                        (u32) rspq->rspbuf);
3099 #endif
3100         } else {
3101                 ASSERT(rspq->offset == SLIC_RSPQ_BUFSINPAGE);
3102                 slic_reg64_write(adapter, &adapter->slic_regs->slic_rbar64,
3103                         (rspq->paddr[rspq->pageindex] | SLIC_RSPQ_BUFSINPAGE),
3104                         &adapter->slic_regs->slic_addr_upper, 0, DONT_FLUSH);
3105                 rspq->pageindex = (++rspq->pageindex) % rspq->num_pages;
3106                 rspq->offset = 0;
3107                 rspq->rspbuf = (struct slic_rspbuf *)
3108                                                 rspq->vaddr[rspq->pageindex];
3109 #ifndef CONFIG_X86_64
3110                 ASSERT(((u32) rspq->rspbuf & 0xFFFFF000) ==
3111                        (u32) rspq->rspbuf);
3112 #endif
3113         }
3114 #ifndef CONFIG_X86_64
3115         ASSERT(((u32) buf & 0xFFFFFFE0) == (u32) buf);
3116 #endif
3117         return buf;
3118 }
3119
3120 static void slic_cmdqmem_init(struct adapter *adapter)
3121 {
3122         struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem;
3123
3124         memset(cmdqmem, 0, sizeof(struct slic_cmdqmem));
3125 }
3126
3127 static void slic_cmdqmem_free(struct adapter *adapter)
3128 {
3129         struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem;
3130         int i;
3131
3132         for (i = 0; i < SLIC_CMDQ_MAXPAGES; i++) {
3133                 if (cmdqmem->pages[i]) {
3134                         pci_free_consistent(adapter->pcidev,
3135                                             PAGE_SIZE,
3136                                             (void *) cmdqmem->pages[i],
3137                                             cmdqmem->dma_pages[i]);
3138                 }
3139         }
3140         memset(cmdqmem, 0, sizeof(struct slic_cmdqmem));
3141 }
3142
3143 static u32 *slic_cmdqmem_addpage(struct adapter *adapter)
3144 {
3145         struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem;
3146         u32 *pageaddr;
3147
3148         if (cmdqmem->pagecnt >= SLIC_CMDQ_MAXPAGES)
3149                 return NULL;
3150         pageaddr = pci_alloc_consistent(adapter->pcidev,
3151                                         PAGE_SIZE,
3152                                         &cmdqmem->dma_pages[cmdqmem->pagecnt]);
3153         if (!pageaddr)
3154                 return NULL;
3155 #ifndef CONFIG_X86_64
3156         ASSERT(((u32) pageaddr & 0xFFFFF000) == (u32) pageaddr);
3157 #endif
3158         cmdqmem->pages[cmdqmem->pagecnt] = pageaddr;
3159         cmdqmem->pagecnt++;
3160         return pageaddr;
3161 }
3162
3163 static int slic_cmdq_init(struct adapter *adapter)
3164 {
3165         int i;
3166         u32 *pageaddr;
3167
3168         ASSERT(adapter->state == ADAPT_DOWN);
3169         memset(&adapter->cmdq_all, 0, sizeof(struct slic_cmdqueue));
3170         memset(&adapter->cmdq_free, 0, sizeof(struct slic_cmdqueue));
3171         memset(&adapter->cmdq_done, 0, sizeof(struct slic_cmdqueue));
3172         spin_lock_init(&adapter->cmdq_all.lock.lock);
3173         spin_lock_init(&adapter->cmdq_free.lock.lock);
3174         spin_lock_init(&adapter->cmdq_done.lock.lock);
3175         slic_cmdqmem_init(adapter);
3176         adapter->slic_handle_ix = 1;
3177         for (i = 0; i < SLIC_CMDQ_INITPAGES; i++) {
3178                 pageaddr = slic_cmdqmem_addpage(adapter);
3179 #ifndef CONFIG_X86_64
3180                 ASSERT(((u32) pageaddr & 0xFFFFF000) == (u32) pageaddr);
3181 #endif
3182                 if (!pageaddr) {
3183                         slic_cmdq_free(adapter);
3184                         return STATUS_FAILURE;
3185                 }
3186                 slic_cmdq_addcmdpage(adapter, pageaddr);
3187         }
3188         adapter->slic_handle_ix = 1;
3189
3190         return STATUS_SUCCESS;
3191 }
3192
3193 static void slic_cmdq_free(struct adapter *adapter)
3194 {
3195         struct slic_hostcmd *cmd;
3196
3197         cmd = adapter->cmdq_all.head;
3198         while (cmd) {
3199                 if (cmd->busy) {
3200                         struct sk_buff *tempskb;
3201
3202                         tempskb = cmd->skb;
3203                         if (tempskb) {
3204                                 cmd->skb = NULL;
3205                                 dev_kfree_skb_irq(tempskb);
3206                         }
3207                 }
3208                 cmd = cmd->next_all;
3209         }
3210         memset(&adapter->cmdq_all, 0, sizeof(struct slic_cmdqueue));
3211         memset(&adapter->cmdq_free, 0, sizeof(struct slic_cmdqueue));
3212         memset(&adapter->cmdq_done, 0, sizeof(struct slic_cmdqueue));
3213         slic_cmdqmem_free(adapter);
3214 }
3215
3216 static void slic_cmdq_reset(struct adapter *adapter)
3217 {
3218         struct slic_hostcmd *hcmd;
3219         struct sk_buff *skb;
3220         u32 outstanding;
3221
3222         spin_lock_irqsave(&adapter->cmdq_free.lock.lock,
3223                         adapter->cmdq_free.lock.flags);
3224         spin_lock_irqsave(&adapter->cmdq_done.lock.lock,
3225                         adapter->cmdq_done.lock.flags);
3226         outstanding = adapter->cmdq_all.count - adapter->cmdq_done.count;
3227         outstanding -= adapter->cmdq_free.count;
3228         hcmd = adapter->cmdq_all.head;
3229         while (hcmd) {
3230                 if (hcmd->busy) {
3231                         skb = hcmd->skb;
3232                         ASSERT(skb);
3233                         hcmd->busy = 0;
3234                         hcmd->skb = NULL;
3235                         dev_kfree_skb_irq(skb);
3236                 }
3237                 hcmd = hcmd->next_all;
3238         }
3239         adapter->cmdq_free.count = 0;
3240         adapter->cmdq_free.head = NULL;
3241         adapter->cmdq_free.tail = NULL;
3242         adapter->cmdq_done.count = 0;
3243         adapter->cmdq_done.head = NULL;
3244         adapter->cmdq_done.tail = NULL;
3245         adapter->cmdq_free.head = adapter->cmdq_all.head;
3246         hcmd = adapter->cmdq_all.head;
3247         while (hcmd) {
3248                 adapter->cmdq_free.count++;
3249                 hcmd->next = hcmd->next_all;
3250                 hcmd = hcmd->next_all;
3251         }
3252         if (adapter->cmdq_free.count != adapter->cmdq_all.count) {
3253                 dev_err(&adapter->netdev->dev,
3254                         "free_count %d != all count %d\n",
3255                         adapter->cmdq_free.count, adapter->cmdq_all.count);
3256         }
3257         spin_unlock_irqrestore(&adapter->cmdq_done.lock.lock,
3258                                 adapter->cmdq_done.lock.flags);
3259         spin_unlock_irqrestore(&adapter->cmdq_free.lock.lock,
3260                                 adapter->cmdq_free.lock.flags);
3261 }
3262
3263 static void slic_cmdq_addcmdpage(struct adapter *adapter, u32 *page)
3264 {
3265         struct slic_hostcmd *cmd;
3266         struct slic_hostcmd *prev;
3267         struct slic_hostcmd *tail;
3268         struct slic_cmdqueue *cmdq;
3269         int cmdcnt;
3270         void *cmdaddr;
3271         ulong phys_addr;
3272         u32 phys_addrl;
3273         u32 phys_addrh;
3274         struct slic_handle *pslic_handle;
3275
3276         cmdaddr = page;
3277         cmd = (struct slic_hostcmd *)cmdaddr;
3278         cmdcnt = 0;
3279
3280         phys_addr = virt_to_bus((void *)page);
3281         phys_addrl = SLIC_GET_ADDR_LOW(phys_addr);
3282         phys_addrh = SLIC_GET_ADDR_HIGH(phys_addr);
3283
3284         prev = NULL;
3285         tail = cmd;
3286         while ((cmdcnt < SLIC_CMDQ_CMDSINPAGE) &&
3287                (adapter->slic_handle_ix < 256)) {
3288                 /* Allocate and initialize a SLIC_HANDLE for this command */
3289                 SLIC_GET_SLIC_HANDLE(adapter, pslic_handle);
3290                 if (pslic_handle == NULL)
3291                         ASSERT(0);
3292                 ASSERT(pslic_handle ==
3293                        &adapter->slic_handles[pslic_handle->token.
3294                                               handle_index]);
3295                 pslic_handle->type = SLIC_HANDLE_CMD;
3296                 pslic_handle->address = (void *) cmd;
3297                 pslic_handle->offset = (ushort) adapter->slic_handle_ix++;
3298                 pslic_handle->other_handle = NULL;
3299                 pslic_handle->next = NULL;
3300
3301                 cmd->pslic_handle = pslic_handle;
3302                 cmd->cmd64.hosthandle = pslic_handle->token.handle_token;
3303                 cmd->busy = false;
3304                 cmd->paddrl = phys_addrl;
3305                 cmd->paddrh = phys_addrh;
3306                 cmd->next_all = prev;
3307                 cmd->next = prev;
3308                 prev = cmd;
3309                 phys_addrl += SLIC_HOSTCMD_SIZE;
3310                 cmdaddr += SLIC_HOSTCMD_SIZE;
3311
3312                 cmd = (struct slic_hostcmd *)cmdaddr;
3313                 cmdcnt++;
3314         }
3315
3316         cmdq = &adapter->cmdq_all;
3317         cmdq->count += cmdcnt;  /*  SLIC_CMDQ_CMDSINPAGE;   mooktodo */
3318         tail->next_all = cmdq->head;
3319         cmdq->head = prev;
3320         cmdq = &adapter->cmdq_free;
3321         spin_lock_irqsave(&cmdq->lock.lock, cmdq->lock.flags);
3322         cmdq->count += cmdcnt;  /*  SLIC_CMDQ_CMDSINPAGE;   mooktodo */
3323         tail->next = cmdq->head;
3324         cmdq->head = prev;
3325         spin_unlock_irqrestore(&cmdq->lock.lock, cmdq->lock.flags);
3326 }
3327
3328 static struct slic_hostcmd *slic_cmdq_getfree(struct adapter *adapter)
3329 {
3330         struct slic_cmdqueue *cmdq = &adapter->cmdq_free;
3331         struct slic_hostcmd *cmd = NULL;
3332
3333 lock_and_retry:
3334         spin_lock_irqsave(&cmdq->lock.lock, cmdq->lock.flags);
3335 retry:
3336         cmd = cmdq->head;
3337         if (cmd) {
3338                 cmdq->head = cmd->next;
3339                 cmdq->count--;
3340                 spin_unlock_irqrestore(&cmdq->lock.lock, cmdq->lock.flags);
3341         } else {
3342                 slic_cmdq_getdone(adapter);
3343                 cmd = cmdq->head;
3344                 if (cmd) {
3345                         goto retry;
3346                 } else {
3347                         u32 *pageaddr;
3348
3349                         spin_unlock_irqrestore(&cmdq->lock.lock,
3350                                                 cmdq->lock.flags);
3351                         pageaddr = slic_cmdqmem_addpage(adapter);
3352                         if (pageaddr) {
3353                                 slic_cmdq_addcmdpage(adapter, pageaddr);
3354                                 goto lock_and_retry;
3355                         }
3356                 }
3357         }
3358         return cmd;
3359 }
3360
3361 static void slic_cmdq_getdone(struct adapter *adapter)
3362 {
3363         struct slic_cmdqueue *done_cmdq = &adapter->cmdq_done;
3364         struct slic_cmdqueue *free_cmdq = &adapter->cmdq_free;
3365
3366         ASSERT(free_cmdq->head == NULL);
3367         spin_lock_irqsave(&done_cmdq->lock.lock, done_cmdq->lock.flags);
3368
3369         free_cmdq->head = done_cmdq->head;
3370         free_cmdq->count = done_cmdq->count;
3371         done_cmdq->head = NULL;
3372         done_cmdq->tail = NULL;
3373         done_cmdq->count = 0;
3374         spin_unlock_irqrestore(&done_cmdq->lock.lock, done_cmdq->lock.flags);
3375 }
3376
3377 static void slic_cmdq_putdone_irq(struct adapter *adapter,
3378                                 struct slic_hostcmd *cmd)
3379 {
3380         struct slic_cmdqueue *cmdq = &adapter->cmdq_done;
3381
3382         spin_lock(&cmdq->lock.lock);
3383         cmd->busy = 0;
3384         cmd->next = cmdq->head;
3385         cmdq->head = cmd;
3386         cmdq->count++;
3387         if ((adapter->xmitq_full) && (cmdq->count > 10))
3388                 netif_wake_queue(adapter->netdev);
3389         spin_unlock(&cmdq->lock.lock);
3390 }
3391
3392 static int slic_rcvqueue_init(struct adapter *adapter)
3393 {
3394         int i, count;
3395         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3396
3397         ASSERT(adapter->state == ADAPT_DOWN);
3398         rcvq->tail = NULL;
3399         rcvq->head = NULL;
3400         rcvq->size = SLIC_RCVQ_ENTRIES;
3401         rcvq->errors = 0;
3402         rcvq->count = 0;
3403         i = (SLIC_RCVQ_ENTRIES / SLIC_RCVQ_FILLENTRIES);
3404         count = 0;
3405         while (i) {
3406                 count += slic_rcvqueue_fill(adapter);
3407                 i--;
3408         }
3409         if (rcvq->count < SLIC_RCVQ_MINENTRIES) {
3410                 slic_rcvqueue_free(adapter);
3411                 return STATUS_FAILURE;
3412         }
3413         return STATUS_SUCCESS;
3414 }
3415
3416 static void slic_rcvqueue_free(struct adapter *adapter)
3417 {
3418         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3419         struct sk_buff *skb;
3420
3421         while (rcvq->head) {
3422                 skb = rcvq->head;
3423                 rcvq->head = rcvq->head->next;
3424                 dev_kfree_skb(skb);
3425         }
3426         rcvq->tail = NULL;
3427         rcvq->head = NULL;
3428         rcvq->count = 0;
3429 }
3430
3431 static struct sk_buff *slic_rcvqueue_getnext(struct adapter *adapter)
3432 {
3433         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3434         struct sk_buff *skb;
3435         struct slic_rcvbuf *rcvbuf;
3436         int count;
3437
3438         if (rcvq->count) {
3439                 skb = rcvq->head;
3440                 rcvbuf = (struct slic_rcvbuf *)skb->head;
3441                 ASSERT(rcvbuf);
3442
3443                 if (rcvbuf->status & IRHDDR_SVALID) {
3444                         rcvq->head = rcvq->head->next;
3445                         skb->next = NULL;
3446                         rcvq->count--;
3447                 } else {
3448                         skb = NULL;
3449                 }
3450         } else {
3451                 dev_err(&adapter->netdev->dev,
3452                         "RcvQ Empty!! rcvq[%p] count[%x]\n", rcvq, rcvq->count);
3453                 skb = NULL;
3454         }
3455         while (rcvq->count < SLIC_RCVQ_FILLTHRESH) {
3456                 count = slic_rcvqueue_fill(adapter);
3457                 if (!count)
3458                         break;
3459         }
3460         if (skb)
3461                 rcvq->errors = 0;
3462         return skb;
3463 }
3464
3465 static int slic_rcvqueue_fill(struct adapter *adapter)
3466 {
3467         void *paddr;
3468         u32 paddrl;
3469         u32 paddrh;
3470         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3471         int i = 0;
3472         struct device *dev = &adapter->netdev->dev;
3473
3474         while (i < SLIC_RCVQ_FILLENTRIES) {
3475                 struct slic_rcvbuf *rcvbuf;
3476                 struct sk_buff *skb;
3477 #ifdef KLUDGE_FOR_4GB_BOUNDARY
3478 retry_rcvqfill:
3479 #endif
3480                 skb = alloc_skb(SLIC_RCVQ_RCVBUFSIZE, GFP_ATOMIC);
3481                 if (skb) {
3482                         paddr = (void *)pci_map_single(adapter->pcidev,
3483                                                           skb->data,
3484                                                           SLIC_RCVQ_RCVBUFSIZE,
3485                                                           PCI_DMA_FROMDEVICE);
3486                         paddrl = SLIC_GET_ADDR_LOW(paddr);
3487                         paddrh = SLIC_GET_ADDR_HIGH(paddr);
3488
3489                         skb->len = SLIC_RCVBUF_HEADSIZE;
3490                         rcvbuf = (struct slic_rcvbuf *)skb->head;
3491                         rcvbuf->status = 0;
3492                         skb->next = NULL;
3493 #ifdef KLUDGE_FOR_4GB_BOUNDARY
3494                         if (paddrl == 0) {
3495                                 dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n",
3496                                         __func__);
3497                                 dev_err(dev, "skb[%p] PROBLEM\n", skb);
3498                                 dev_err(dev, "         skbdata[%p]\n", skb->data);
3499                                 dev_err(dev, "         skblen[%x]\n", skb->len);
3500                                 dev_err(dev, "         paddr[%p]\n", paddr);
3501                                 dev_err(dev, "         paddrl[%x]\n", paddrl);
3502                                 dev_err(dev, "         paddrh[%x]\n", paddrh);
3503                                 dev_err(dev, "         rcvq->head[%p]\n", rcvq->head);
3504                                 dev_err(dev, "         rcvq->tail[%p]\n", rcvq->tail);
3505                                 dev_err(dev, "         rcvq->count[%x]\n", rcvq->count);
3506                                 dev_err(dev, "SKIP THIS SKB!!!!!!!!\n");
3507                                 goto retry_rcvqfill;
3508                         }
3509 #else
3510                         if (paddrl == 0) {
3511                                 dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n",
3512                                         __func__);
3513                                 dev_err(dev, "skb[%p] PROBLEM\n", skb);
3514                                 dev_err(dev, "         skbdata[%p]\n", skb->data);
3515                                 dev_err(dev, "         skblen[%x]\n", skb->len);
3516                                 dev_err(dev, "         paddr[%p]\n", paddr);
3517                                 dev_err(dev, "         paddrl[%x]\n", paddrl);
3518                                 dev_err(dev, "         paddrh[%x]\n", paddrh);
3519                                 dev_err(dev, "         rcvq->head[%p]\n", rcvq->head);
3520                                 dev_err(dev, "         rcvq->tail[%p]\n", rcvq->tail);
3521                                 dev_err(dev, "         rcvq->count[%x]\n", rcvq->count);
3522                                 dev_err(dev, "GIVE TO CARD ANYWAY\n");
3523                         }
3524 #endif
3525                         if (paddrh == 0) {
3526                                 slic_reg32_write(&adapter->slic_regs->slic_hbar,
3527                                                  (u32)paddrl, DONT_FLUSH);
3528                         } else {
3529                                 slic_reg64_write(adapter,
3530                                         &adapter->slic_regs->slic_hbar64,
3531                                         paddrl,
3532                                         &adapter->slic_regs->slic_addr_upper,
3533                                         paddrh, DONT_FLUSH);
3534                         }
3535                         if (rcvq->head)
3536                                 rcvq->tail->next = skb;
3537                         else
3538                                 rcvq->head = skb;
3539                         rcvq->tail = skb;
3540                         rcvq->count++;
3541                         i++;
3542                 } else {
3543                         dev_err(&adapter->netdev->dev,
3544                                 "slic_rcvqueue_fill could only get [%d] skbuffs\n",
3545                                 i);
3546                         break;
3547                 }
3548         }
3549         return i;
3550 }
3551
3552 static u32 slic_rcvqueue_reinsert(struct adapter *adapter, struct sk_buff *skb)
3553 {
3554         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3555         void *paddr;
3556         u32 paddrl;
3557         u32 paddrh;
3558         struct slic_rcvbuf *rcvbuf = (struct slic_rcvbuf *)skb->head;
3559         struct device *dev;
3560
3561         ASSERT(skb->len == SLIC_RCVBUF_HEADSIZE);
3562
3563         paddr = (void *)pci_map_single(adapter->pcidev, skb->head,
3564                                   SLIC_RCVQ_RCVBUFSIZE, PCI_DMA_FROMDEVICE);
3565         rcvbuf->status = 0;
3566         skb->next = NULL;
3567
3568         paddrl = SLIC_GET_ADDR_LOW(paddr);
3569         paddrh = SLIC_GET_ADDR_HIGH(paddr);
3570
3571         if (paddrl == 0) {
3572                 dev = &adapter->netdev->dev;
3573                 dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n",
3574                         __func__);
3575                 dev_err(dev, "skb[%p] PROBLEM\n", skb);
3576                 dev_err(dev, "         skbdata[%p]\n", skb->data);
3577                 dev_err(dev, "         skblen[%x]\n", skb->len);
3578                 dev_err(dev, "         paddr[%p]\n", paddr);
3579                 dev_err(dev, "         paddrl[%x]\n", paddrl);
3580                 dev_err(dev, "         paddrh[%x]\n", paddrh);
3581                 dev_err(dev, "         rcvq->head[%p]\n", rcvq->head);
3582                 dev_err(dev, "         rcvq->tail[%p]\n", rcvq->tail);
3583                 dev_err(dev, "         rcvq->count[%x]\n", rcvq->count);
3584         }
3585         if (paddrh == 0) {
3586                 slic_reg32_write(&adapter->slic_regs->slic_hbar, (u32)paddrl,
3587                                  DONT_FLUSH);
3588         } else {
3589                 slic_reg64_write(adapter, &adapter->slic_regs->slic_hbar64,
3590                                  paddrl, &adapter->slic_regs->slic_addr_upper,
3591                                  paddrh, DONT_FLUSH);
3592         }
3593         if (rcvq->head)
3594                 rcvq->tail->next = skb;
3595         else
3596                 rcvq->head = skb;
3597         rcvq->tail = skb;
3598         rcvq->count++;
3599         return rcvq->count;
3600 }
3601
3602 static int slic_debug_card_show(struct seq_file *seq, void *v)
3603 {
3604 #ifdef MOOKTODO
3605         int i;
3606         struct sliccard *card = seq->private;
3607         struct slic_config *config = &card->config;
3608         unsigned char *fru = (unsigned char *)(&card->config.atk_fru);
3609         unsigned char *oemfru = (unsigned char *)(&card->config.OemFru);
3610 #endif
3611
3612         seq_printf(seq, "driver_version           : %s\n", slic_proc_version);
3613         seq_printf(seq, "Microcode versions:           \n");
3614         seq_printf(seq, "    Gigabit (gb)         : %s %s\n",
3615                     MOJAVE_UCODE_VERS_STRING, MOJAVE_UCODE_VERS_DATE);
3616         seq_printf(seq, "    Gigabit Receiver     : %s %s\n",
3617                     GB_RCVUCODE_VERS_STRING, GB_RCVUCODE_VERS_DATE);
3618         seq_printf(seq, "Vendor                   : %s\n", slic_vendor);
3619         seq_printf(seq, "Product Name             : %s\n", slic_product_name);
3620 #ifdef MOOKTODO
3621         seq_printf(seq, "VendorId                 : %4.4X\n",
3622                     config->VendorId);
3623         seq_printf(seq, "DeviceId                 : %4.4X\n",
3624                     config->DeviceId);
3625         seq_printf(seq, "RevisionId               : %2.2x\n",
3626                     config->RevisionId);
3627         seq_printf(seq, "Bus    #                 : %d\n", card->busnumber);
3628         seq_printf(seq, "Device #                 : %d\n", card->slotnumber);
3629         seq_printf(seq, "Interfaces               : %d\n", card->card_size);
3630         seq_printf(seq, "     Initialized         : %d\n",
3631                     card->adapters_activated);
3632         seq_printf(seq, "     Allocated           : %d\n",
3633                     card->adapters_allocated);
3634         ASSERT(card->card_size <= SLIC_NBR_MACS);
3635         for (i = 0; i < card->card_size; i++) {
3636                 seq_printf(seq,
3637                            "     MAC%d : %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
3638                            i, config->macinfo[i].macaddrA[0],
3639                            config->macinfo[i].macaddrA[1],
3640                            config->macinfo[i].macaddrA[2],
3641                            config->macinfo[i].macaddrA[3],
3642                            config->macinfo[i].macaddrA[4],
3643                            config->macinfo[i].macaddrA[5]);
3644         }
3645         seq_printf(seq, "     IF  Init State Duplex/Speed irq\n");
3646         seq_printf(seq, "     -------------------------------\n");
3647         for (i = 0; i < card->adapters_allocated; i++) {
3648                 struct adapter *adapter;
3649
3650                 adapter = card->adapter[i];
3651                 if (adapter) {
3652                         seq_printf(seq,
3653                                     "     %d   %d   %s  %s  %s    0x%X\n",
3654                                     adapter->physport, adapter->state,
3655                                     SLIC_LINKSTATE(adapter->linkstate),
3656                                     SLIC_DUPLEX(adapter->linkduplex),
3657                                     SLIC_SPEED(adapter->linkspeed),
3658                                     (uint) adapter->irq);
3659                 }
3660         }
3661         seq_printf(seq, "Generation #             : %4.4X\n", card->gennumber);
3662         seq_printf(seq, "RcvQ max entries         : %4.4X\n",
3663                     SLIC_RCVQ_ENTRIES);
3664         seq_printf(seq, "Ping Status              : %8.8X\n",
3665                     card->pingstatus);
3666         seq_printf(seq, "Minimum grant            : %2.2x\n",
3667                     config->MinGrant);
3668         seq_printf(seq, "Maximum Latency          : %2.2x\n", config->MaxLat);
3669         seq_printf(seq, "PciStatus                : %4.4x\n",
3670                     config->Pcistatus);
3671         seq_printf(seq, "Debug Device Id          : %4.4x\n",
3672                     config->DbgDevId);
3673         seq_printf(seq, "DRAM ROM Function        : %4.4x\n",
3674                     config->DramRomFn);
3675         seq_printf(seq, "Network interface Pin 1  : %2.2x\n",
3676                     config->NetIntPin1);
3677         seq_printf(seq, "Network interface Pin 2  : %2.2x\n",
3678                     config->NetIntPin1);
3679         seq_printf(seq, "Network interface Pin 3  : %2.2x\n",
3680                     config->NetIntPin1);
3681         seq_printf(seq, "PM capabilities          : %4.4X\n",
3682                     config->PMECapab);
3683         seq_printf(seq, "Network Clock Controls   : %4.4X\n",
3684                     config->NwClkCtrls);
3685
3686         switch (config->FruFormat) {
3687         case ATK_FRU_FORMAT:
3688                 {
3689                         seq_printf(seq,
3690                             "Vendor                   : Alacritech, Inc.\n");
3691                         seq_printf(seq,
3692                             "Assembly #               : %c%c%c%c%c%c\n",
3693                                     fru[0], fru[1], fru[2], fru[3], fru[4],
3694                                     fru[5]);
3695                         seq_printf(seq,
3696                                     "Revision #               : %c%c\n",
3697                                     fru[6], fru[7]);
3698
3699                         if (config->OEMFruFormat == VENDOR4_FRU_FORMAT) {
3700                                 seq_printf(seq,
3701                                             "Serial   #               : "
3702                                             "%c%c%c%c%c%c%c%c%c%c%c%c\n",
3703                                             fru[8], fru[9], fru[10],
3704                                             fru[11], fru[12], fru[13],
3705                                             fru[16], fru[17], fru[18],
3706                                             fru[19], fru[20], fru[21]);
3707                         } else {
3708                                 seq_printf(seq,
3709                                             "Serial   #               : "
3710                                             "%c%c%c%c%c%c%c%c%c%c%c%c%c%c\n",
3711                                             fru[8], fru[9], fru[10],
3712                                             fru[11], fru[12], fru[13],
3713                                             fru[14], fru[15], fru[16],
3714                                             fru[17], fru[18], fru[19],
3715                                             fru[20], fru[21]);
3716                         }
3717                         break;
3718                 }
3719
3720         default:
3721                 {
3722                         seq_printf(seq,
3723                             "Vendor                   : Alacritech, Inc.\n");
3724                         seq_printf(seq,
3725                             "Serial   #               : Empty FRU\n");
3726                         break;
3727                 }
3728         }
3729
3730         switch (config->OEMFruFormat) {
3731         case VENDOR1_FRU_FORMAT:
3732                 {
3733                         seq_printf(seq, "FRU Information:\n");
3734                         seq_printf(seq, "    Commodity #          : %c\n",
3735                                     oemfru[0]);
3736                         seq_printf(seq,
3737                                     "    Assembly #           : %c%c%c%c\n",
3738                                     oemfru[1], oemfru[2], oemfru[3], oemfru[4]);
3739                         seq_printf(seq,
3740                                     "    Revision #           : %c%c\n",
3741                                     oemfru[5], oemfru[6]);
3742                         seq_printf(seq,
3743                                     "    Supplier #           : %c%c\n",
3744                                     oemfru[7], oemfru[8]);
3745                         seq_printf(seq,
3746                                     "    Date                 : %c%c\n",
3747                                     oemfru[9], oemfru[10]);
3748                         seq_sprintf(seq,
3749                                     "    Sequence #           : %c%c%c\n",
3750                                     oemfru[11], oemfru[12], oemfru[13]);
3751                         break;
3752                 }
3753
3754         case VENDOR2_FRU_FORMAT:
3755                 {
3756                         seq_printf(seq, "FRU Information:\n");
3757                         seq_printf(seq,
3758                                     "    Part     #           : "
3759                                     "%c%c%c%c%c%c%c%c\n",
3760                                     oemfru[0], oemfru[1], oemfru[2],
3761                                     oemfru[3], oemfru[4], oemfru[5],
3762                                     oemfru[6], oemfru[7]);
3763                         seq_printf(seq,
3764                                     "    Supplier #           : %c%c%c%c%c\n",
3765                                     oemfru[8], oemfru[9], oemfru[10],
3766                                     oemfru[11], oemfru[12]);
3767                         seq_printf(seq,
3768                                     "    Date                 : %c%c%c\n",
3769                                     oemfru[13], oemfru[14], oemfru[15]);
3770                         seq_sprintf(seq,
3771                                     "    Sequence #           : %c%c%c%c\n",
3772                                     oemfru[16], oemfru[17], oemfru[18],
3773                                     oemfru[19]);
3774                         break;
3775                 }
3776
3777         case VENDOR3_FRU_FORMAT:
3778                 {
3779                         seq_printf(seq, "FRU Information:\n");
3780                 }
3781
3782         case VENDOR4_FRU_FORMAT:
3783                 {
3784                         seq_printf(seq, "FRU Information:\n");
3785                         seq_printf(seq,
3786                                     "    FRU Number           : "
3787                                     "%c%c%c%c%c%c%c%c\n",
3788                                     oemfru[0], oemfru[1], oemfru[2],
3789                                     oemfru[3], oemfru[4], oemfru[5],
3790                                     oemfru[6], oemfru[7]);
3791                         seq_sprintf(seq,
3792                                     "    Part Number          : "
3793                                     "%c%c%c%c%c%c%c%c\n",
3794                                     oemfru[8], oemfru[9], oemfru[10],
3795                                     oemfru[11], oemfru[12], oemfru[13],
3796                                     oemfru[14], oemfru[15]);
3797                         seq_printf(seq,
3798                                     "    EC Level             : "
3799                                     "%c%c%c%c%c%c%c%c\n",
3800                                     oemfru[16], oemfru[17], oemfru[18],
3801                                     oemfru[19], oemfru[20], oemfru[21],
3802                                     oemfru[22], oemfru[23]);
3803                         break;
3804                 }
3805
3806         default:
3807                 break;
3808         }
3809 #endif
3810
3811         return 0;
3812 }
3813
3814 static int slic_debug_adapter_show(struct seq_file *seq, void *v)
3815 {
3816         struct adapter *adapter = seq->private;
3817
3818         if ((adapter->netdev) && (adapter->netdev->name)) {
3819                 seq_printf(seq, "info: interface          : %s\n",
3820                             adapter->netdev->name);
3821         }
3822         seq_printf(seq, "info: status             : %s\n",
3823                 SLIC_LINKSTATE(adapter->linkstate));
3824         seq_printf(seq, "info: port               : %d\n",
3825                 adapter->physport);
3826         seq_printf(seq, "info: speed              : %s\n",
3827                 SLIC_SPEED(adapter->linkspeed));
3828         seq_printf(seq, "info: duplex             : %s\n",
3829                 SLIC_DUPLEX(adapter->linkduplex));
3830         seq_printf(seq, "info: irq                : 0x%X\n",
3831                 (uint) adapter->irq);
3832         seq_printf(seq, "info: Interrupt Agg Delay: %d usec\n",
3833                 adapter->card->loadlevel_current);
3834         seq_printf(seq, "info: RcvQ max entries   : %4.4X\n",
3835                 SLIC_RCVQ_ENTRIES);
3836         seq_printf(seq, "info: RcvQ current       : %4.4X\n",
3837                     adapter->rcvqueue.count);
3838         seq_printf(seq, "rx stats: packets                  : %8.8lX\n",
3839                     adapter->stats.rx_packets);
3840         seq_printf(seq, "rx stats: bytes                    : %8.8lX\n",
3841                     adapter->stats.rx_bytes);
3842         seq_printf(seq, "rx stats: broadcasts               : %8.8X\n",
3843                     adapter->rcv_broadcasts);
3844         seq_printf(seq, "rx stats: multicasts               : %8.8X\n",
3845                     adapter->rcv_multicasts);
3846         seq_printf(seq, "rx stats: unicasts                 : %8.8X\n",
3847                     adapter->rcv_unicasts);
3848         seq_printf(seq, "rx stats: errors                   : %8.8X\n",
3849                     (u32) adapter->slic_stats.iface.rcv_errors);
3850         seq_printf(seq, "rx stats: Missed errors            : %8.8X\n",
3851                     (u32) adapter->slic_stats.iface.rcv_discards);
3852         seq_printf(seq, "rx stats: drops                    : %8.8X\n",
3853                         (u32) adapter->rcv_drops);
3854         seq_printf(seq, "tx stats: packets                  : %8.8lX\n",
3855                         adapter->stats.tx_packets);
3856         seq_printf(seq, "tx stats: bytes                    : %8.8lX\n",
3857                         adapter->stats.tx_bytes);
3858         seq_printf(seq, "tx stats: errors                   : %8.8X\n",
3859                         (u32) adapter->slic_stats.iface.xmt_errors);
3860         seq_printf(seq, "rx stats: multicasts               : %8.8lX\n",
3861                         adapter->stats.multicast);
3862         seq_printf(seq, "tx stats: collision errors         : %8.8X\n",
3863                         (u32) adapter->slic_stats.iface.xmit_collisions);
3864         seq_printf(seq, "perf: Max rcv frames/isr           : %8.8X\n",
3865                         adapter->max_isr_rcvs);
3866         seq_printf(seq, "perf: Rcv interrupt yields         : %8.8X\n",
3867                         adapter->rcv_interrupt_yields);
3868         seq_printf(seq, "perf: Max xmit complete/isr        : %8.8X\n",
3869                         adapter->max_isr_xmits);
3870         seq_printf(seq, "perf: error interrupts             : %8.8X\n",
3871                         adapter->error_interrupts);
3872         seq_printf(seq, "perf: error rmiss interrupts       : %8.8X\n",
3873                         adapter->error_rmiss_interrupts);
3874         seq_printf(seq, "perf: rcv interrupts               : %8.8X\n",
3875                         adapter->rcv_interrupts);
3876         seq_printf(seq, "perf: xmit interrupts              : %8.8X\n",
3877                         adapter->xmit_interrupts);
3878         seq_printf(seq, "perf: link event interrupts        : %8.8X\n",
3879                         adapter->linkevent_interrupts);
3880         seq_printf(seq, "perf: UPR interrupts               : %8.8X\n",
3881                         adapter->upr_interrupts);
3882         seq_printf(seq, "perf: interrupt count              : %8.8X\n",
3883                         adapter->num_isrs);
3884         seq_printf(seq, "perf: false interrupts             : %8.8X\n",
3885                         adapter->false_interrupts);
3886         seq_printf(seq, "perf: All register writes          : %8.8X\n",
3887                         adapter->all_reg_writes);
3888         seq_printf(seq, "perf: ICR register writes          : %8.8X\n",
3889                         adapter->icr_reg_writes);
3890         seq_printf(seq, "perf: ISR register writes          : %8.8X\n",
3891                         adapter->isr_reg_writes);
3892         seq_printf(seq, "ifevents: overflow 802 errors      : %8.8X\n",
3893                         adapter->if_events.oflow802);
3894         seq_printf(seq, "ifevents: transport overflow errors: %8.8X\n",
3895                         adapter->if_events.Tprtoflow);
3896         seq_printf(seq, "ifevents: underflow errors         : %8.8X\n",
3897                         adapter->if_events.uflow802);
3898         seq_printf(seq, "ifevents: receive early            : %8.8X\n",
3899                         adapter->if_events.rcvearly);
3900         seq_printf(seq, "ifevents: buffer overflows         : %8.8X\n",
3901                         adapter->if_events.Bufov);
3902         seq_printf(seq, "ifevents: carrier errors           : %8.8X\n",
3903                         adapter->if_events.Carre);
3904         seq_printf(seq, "ifevents: Long                     : %8.8X\n",
3905                         adapter->if_events.Longe);
3906         seq_printf(seq, "ifevents: invalid preambles        : %8.8X\n",
3907                         adapter->if_events.Invp);
3908         seq_printf(seq, "ifevents: CRC errors               : %8.8X\n",
3909                         adapter->if_events.Crc);
3910         seq_printf(seq, "ifevents: dribble nibbles          : %8.8X\n",
3911                         adapter->if_events.Drbl);
3912         seq_printf(seq, "ifevents: Code violations          : %8.8X\n",
3913                         adapter->if_events.Code);
3914         seq_printf(seq, "ifevents: TCP checksum errors      : %8.8X\n",
3915                         adapter->if_events.TpCsum);
3916         seq_printf(seq, "ifevents: TCP header short errors  : %8.8X\n",
3917                         adapter->if_events.TpHlen);
3918         seq_printf(seq, "ifevents: IP checksum errors       : %8.8X\n",
3919                         adapter->if_events.IpCsum);
3920         seq_printf(seq, "ifevents: IP frame incompletes     : %8.8X\n",
3921                         adapter->if_events.IpLen);
3922         seq_printf(seq, "ifevents: IP headers shorts        : %8.8X\n",
3923                         adapter->if_events.IpHlen);
3924
3925         return 0;
3926 }
3927 static int slic_debug_adapter_open(struct inode *inode, struct file *file)
3928 {
3929         return single_open(file, slic_debug_adapter_show, inode->i_private);
3930 }
3931
3932 static int slic_debug_card_open(struct inode *inode, struct file *file)
3933 {
3934         return single_open(file, slic_debug_card_show, inode->i_private);
3935 }
3936
3937 static const struct file_operations slic_debug_adapter_fops = {
3938         .owner          = THIS_MODULE,
3939         .open           = slic_debug_adapter_open,
3940         .read           = seq_read,
3941         .llseek         = seq_lseek,
3942         .release        = single_release,
3943 };
3944
3945 static const struct file_operations slic_debug_card_fops = {
3946         .owner          = THIS_MODULE,
3947         .open           = slic_debug_card_open,
3948         .read           = seq_read,
3949         .llseek         = seq_lseek,
3950         .release        = single_release,
3951 };
3952
3953 static void slic_debug_adapter_create(struct adapter *adapter)
3954 {
3955         struct dentry *d;
3956         char    name[7];
3957         struct sliccard *card = adapter->card;
3958
3959         if (!card->debugfs_dir)
3960                 return;
3961
3962         sprintf(name, "port%d", adapter->port);
3963         d = debugfs_create_file(name, S_IRUGO,
3964                                 card->debugfs_dir, adapter,
3965                                 &slic_debug_adapter_fops);
3966         if (!d || IS_ERR(d))
3967                 pr_info(PFX "%s: debugfs create failed\n", name);
3968         else
3969                 adapter->debugfs_entry = d;
3970 }
3971
3972 static void slic_debug_adapter_destroy(struct adapter *adapter)
3973 {
3974         if (adapter->debugfs_entry) {
3975                 debugfs_remove(adapter->debugfs_entry);
3976                 adapter->debugfs_entry = NULL;
3977         }
3978 }
3979
3980 static void slic_debug_card_create(struct sliccard *card)
3981 {
3982         struct dentry *d;
3983         char    name[IFNAMSIZ];
3984
3985         snprintf(name, sizeof(name), "slic%d", card->cardnum);
3986         d = debugfs_create_dir(name, slic_debugfs);
3987         if (!d || IS_ERR(d))
3988                 pr_info(PFX "%s: debugfs create dir failed\n",
3989                                 name);
3990         else {
3991                 card->debugfs_dir = d;
3992                 d = debugfs_create_file("cardinfo", S_IRUGO,
3993                                 slic_debugfs, card,
3994                                 &slic_debug_card_fops);
3995                 if (!d || IS_ERR(d))
3996                         pr_info(PFX "%s: debugfs create failed\n",
3997                                         name);
3998                 else
3999                         card->debugfs_cardinfo = d;
4000         }
4001 }
4002
4003 static void slic_debug_card_destroy(struct sliccard *card)
4004 {
4005         int i;
4006
4007         for (i = 0; i < card->card_size; i++) {
4008                 struct adapter *adapter;
4009
4010                 adapter = card->adapter[i];
4011                 if (adapter)
4012                         slic_debug_adapter_destroy(adapter);
4013         }
4014         if (card->debugfs_cardinfo) {
4015                 debugfs_remove(card->debugfs_cardinfo);
4016                 card->debugfs_cardinfo = NULL;
4017         }
4018         if (card->debugfs_dir) {
4019                 debugfs_remove(card->debugfs_dir);
4020                 card->debugfs_dir = NULL;
4021         }
4022 }
4023
4024 static void slic_debug_init(void)
4025 {
4026         struct dentry *ent;
4027
4028         ent = debugfs_create_dir("slic", NULL);
4029         if (!ent || IS_ERR(ent)) {
4030                 pr_info(PFX "debugfs create directory failed\n");
4031                 return;
4032         }
4033
4034         slic_debugfs = ent;
4035 }
4036
4037 static void slic_debug_cleanup(void)
4038 {
4039         if (slic_debugfs) {
4040                 debugfs_remove(slic_debugfs);
4041                 slic_debugfs = NULL;
4042         }
4043 }
4044
4045 /******************************************************************************/
4046 /****************   MODULE INITIATION / TERMINATION FUNCTIONS   ***************/
4047 /******************************************************************************/
4048
4049 static struct pci_driver slic_driver = {
4050         .name = DRV_NAME,
4051         .id_table = slic_pci_tbl,
4052         .probe = slic_entry_probe,
4053         .remove = __devexit_p(slic_entry_remove),
4054 };
4055
4056 static int __init slic_module_init(void)
4057 {
4058         slic_init_driver();
4059
4060         if (debug >= 0 && slic_debug != debug)
4061                 printk(KERN_DEBUG KBUILD_MODNAME ": debug level is %d.\n",
4062                        debug);
4063         if (debug >= 0)
4064                 slic_debug = debug;
4065
4066         return pci_register_driver(&slic_driver);
4067 }
4068
4069 static void __exit slic_module_cleanup(void)
4070 {
4071         pci_unregister_driver(&slic_driver);
4072         slic_debug_cleanup();
4073 }
4074
4075 module_init(slic_module_init);
4076 module_exit(slic_module_cleanup);