[linux-2.6-block.git] / drivers / scsi / dtc.c

/*
 * DTC 3180/3280 driver, by
 *	Ray Van Tassle	rayvt@comm.mot.com
 *
 *	taken from ...
 *	Trantor T128/T128F/T228 driver by...
 *
 * 	Drew Eckhardt
 *	Visionary Computing
 *	(Unix and Linux consulting and custom programming)
 *	drew@colorado.edu
 *      +1 (303) 440-4894
 */

/*
 * The card is detected and initialized in one of several ways : 
 * 1.  Autoprobe (default) - since the board is memory mapped, 
 *     a BIOS signature is scanned for to locate the registers.
 *     An interrupt is triggered to autoprobe for the interrupt
 *     line.
 *
 * 2.  With command line overrides - dtc=address,irq may be 
 *     used on the LILO command line to override the defaults.
 * 
*/

/*----------------------------------------------------------------*/
/* the following will set the monitor border color (useful to find
 where something crashed or gets stuck at */
/* 1 = blue
 2 = green
 3 = cyan
 4 = red
 5 = magenta
 6 = yellow
 7 = white
*/
#if 0
#define rtrc(i) {inb(0x3da); outb(0x31, 0x3c0); outb((i), 0x3c0);}
#else
#define rtrc(i) {}
#endif


#include <linux/module.h>
#include <linux/blkdev.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <scsi/scsi_host.h>

#include "dtc.h"
#include "NCR5380.h"

/*
 * The DTC3180 & 3280 boards are memory mapped.
 * 
 */

/*
 */
/* Offset from DTC_5380_OFFSET */
#define DTC_CONTROL_REG		0x100	/* rw */
#define D_CR_ACCESS		0x80	/* ro set=can access 3280 registers */
#define CSR_DIR_READ		0x40	/* rw direction, 1 = read 0 = write */

#define CSR_RESET              0x80	/* wo  Resets 53c400 */
#define CSR_5380_REG           0x80	/* ro  5380 registers can be accessed */
#define CSR_TRANS_DIR          0x40	/* rw  Data transfer direction */
#define CSR_SCSI_BUFF_INTR     0x20	/* rw  Enable int on transfer ready */
#define CSR_5380_INTR          0x10	/* rw  Enable 5380 interrupts */
#define CSR_SHARED_INTR        0x08	/* rw  Interrupt sharing */
#define CSR_HOST_BUF_NOT_RDY   0x04	/* ro  Host buffer not ready */
#define CSR_SCSI_BUF_RDY       0x02	/* ro  SCSI buffer ready */
#define CSR_GATED_5380_IRQ     0x01	/* ro  Last block xferred */
#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR | CSR_5380_INTR)


#define DTC_BLK_CNT		0x101	/* rw 
					 * # of 128-byte blocks to transfer */


#define D_CR_ACCESS             0x80	/* ro set=can access 3280 registers */

#define DTC_SWITCH_REG		0x3982	/* ro - DIP switches */
#define DTC_RESUME_XFER		0x3982	/* wo - resume data xfer 
					 * after disconnect/reconnect*/

#define DTC_5380_OFFSET		0x3880	/* 8 registers here, see NCR5380.h */

/*!!!! for dtc, it's a 128 byte buffer at 3900 !!! */
#define DTC_DATA_BUF		0x3900	/* rw 128 bytes long */

static struct override {
	unsigned int address;
	int irq;
} overrides
#ifdef OVERRIDE
[] __initdata = OVERRIDE;
#else
[4] __initdata = {
	{ 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }
};
#endif

#define NO_OVERRIDES ARRAY_SIZE(overrides)

static struct base {
	unsigned long address;
	int noauto;
} bases[] __initdata = {
	{ 0xcc000, 0 },
	{ 0xc8000, 0 },
	{ 0xdc000, 0 },
	{ 0xd8000, 0 }
};

#define NO_BASES ARRAY_SIZE(bases)

static const struct signature {
	const char *string;
	int offset;
} signatures[] = {
	{"DATA TECHNOLOGY CORPORATION BIOS", 0x25},
};

#define NO_SIGNATURES ARRAY_SIZE(signatures)

#ifndef MODULE
/*
 * Function : dtc_setup(char *str, int *ints)
 *
 * Purpose : LILO command line initialization of the overrides array,
 *
 * Inputs : str - unused, ints - array of integer parameters with ints[0]
 *	equal to the number of ints.
 *
 */

static int __init dtc_setup(char *str)
{
	static int commandline_current;
	int i;
	int ints[10];

	get_options(str, ARRAY_SIZE(ints), ints);
	if (ints[0] != 2)
		printk("dtc_setup: usage dtc=address,irq\n");
	else if (commandline_current < NO_OVERRIDES) {
		overrides[commandline_current].address = ints[1];
		overrides[commandline_current].irq = ints[2];
		for (i = 0; i < NO_BASES; ++i)
			if (bases[i].address == ints[1]) {
				bases[i].noauto = 1;
				break;
			}
		++commandline_current;
	}
	return 1;
}

__setup("dtc=", dtc_setup);
#endif

/* 
 * Function : int dtc_detect(struct scsi_host_template * tpnt)
 *
 * Purpose : detects and initializes DTC 3180/3280 controllers
 *	that were autoprobed, overridden on the LILO command line, 
 *	or specified at compile time.
 *
 * Inputs : tpnt - template for this SCSI adapter.
 * 
 * Returns : 1 if a host adapter was found, 0 if not.
 *
*/

static int __init dtc_detect(struct scsi_host_template * tpnt)
{
	static int current_override, current_base;
	struct Scsi_Host *instance;
	unsigned int addr;
	void __iomem *base;
	int sig, count;

	for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
		addr = 0;
		base = NULL;

		if (overrides[current_override].address) {
			addr = overrides[current_override].address;
			base = ioremap(addr, 0x2000);
			if (!base)
				addr = 0;
		} else
			for (; !addr && (current_base < NO_BASES); ++current_base) {
				dprintk(NDEBUG_INIT, "dtc: probing address 0x%08x\n",
				        (unsigned int)bases[current_base].address);
				if (bases[current_base].noauto)
					continue;
				base = ioremap(bases[current_base].address, 0x2000);
				if (!base)
					continue;
				for (sig = 0; sig < NO_SIGNATURES; ++sig) {
					if (check_signature(base + signatures[sig].offset, signatures[sig].string, strlen(signatures[sig].string))) {
						addr = bases[current_base].address;
						dprintk(NDEBUG_INIT, "dtc: detected board\n");
						goto found;
					}
				}
				iounmap(base);
			}

		dprintk(NDEBUG_INIT, "dtc: addr = 0x%08x\n", addr);

		if (!addr)
			break;

found:
		instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
		if (instance == NULL)
			goto out_unmap;

		instance->base = addr;
		((struct NCR5380_hostdata *)(instance)->hostdata)->base = base;

		if (NCR5380_init(instance, FLAG_LATE_DMA_SETUP))
			goto out_unregister;

		NCR5380_maybe_reset_bus(instance);

		NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);	/* Enable int's */
		if (overrides[current_override].irq != IRQ_AUTO)
			instance->irq = overrides[current_override].irq;
		else
			instance->irq = NCR5380_probe_irq(instance, DTC_IRQS);

		/* Compatibility with documented NCR5380 kernel parameters */
		if (instance->irq == 255)
			instance->irq = NO_IRQ;

		/* With interrupts enabled, it will sometimes hang when doing heavy
		 * reads. So better not enable them until I finger it out. */
		instance->irq = NO_IRQ;

		if (instance->irq != NO_IRQ)
			if (request_irq(instance->irq, dtc_intr, 0,
					"dtc", instance)) {
				printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
				instance->irq = NO_IRQ;
			}

		if (instance->irq == NO_IRQ) {
			printk(KERN_WARNING "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
			printk(KERN_WARNING "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
		}

		dprintk(NDEBUG_INIT, "scsi%d : irq = %d\n",
		        instance->host_no, instance->irq);

		++current_override;
		++count;
	}
	return count;

out_unregister:
	scsi_unregister(instance);
out_unmap:
	iounmap(base);
	return count;
}

/*
 * Function : int dtc_biosparam(Disk * disk, struct block_device *dev, int *ip)
 *
 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for 
 *	the specified device / size.
 * 
 * Inputs : size = size of device in sectors (512 bytes), dev = block device
 *	major / minor, ip[] = {heads, sectors, cylinders}  
 *
 * Returns : always 0 (success), initializes ip
 *	
*/

/* 
 * XXX Most SCSI boards use this mapping, I could be incorrect.  Some one
 * using hard disks on a trantor should verify that this mapping corresponds
 * to that used by the BIOS / ASPI driver by running the linux fdisk program
 * and matching the H_C_S coordinates to what DOS uses.
*/

static int dtc_biosparam(struct scsi_device *sdev, struct block_device *dev,
			 sector_t capacity, int *ip)
{
	int size = capacity;

	ip[0] = 64;
	ip[1] = 32;
	ip[2] = size >> 11;
	return 0;
}


/****************************************************************
 * Function : int NCR5380_pread (struct Scsi_Host *instance, 
 *	unsigned char *dst, int len)
 *
 * Purpose : Fast 5380 pseudo-dma read function, reads len bytes to 
 *	dst
 * 
 * Inputs : dst = destination, len = length in bytes
 *
 * Returns : 0 on success, non zero on a failure such as a watchdog 
 * 	timeout.
*/

static inline int dtc_pread(struct Scsi_Host *instance,
                            unsigned char *dst, int len)
{
	unsigned char *d = dst;
	int i;			/* For counting time spent in the poll-loop */
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	i = 0;
	if (instance->irq == NO_IRQ)
		NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
	else
		NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ | CSR_INT_BASE);
	NCR5380_write(DTC_BLK_CNT, len >> 7);	/* Block count */
	rtrc(1);
	while (len > 0) {
		rtrc(2);
		while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
			++i;
		rtrc(3);
		memcpy_fromio(d, hostdata->base + DTC_DATA_BUF, 128);
		d += 128;
		len -= 128;
		rtrc(7);
		/*** with int's on, it sometimes hangs after here.
		 * Looks like something makes HBNR go away. */
	}
	rtrc(4);
	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
		++i;
	rtrc(0);
	return (0);
}

/****************************************************************
 * Function : int NCR5380_pwrite (struct Scsi_Host *instance, 
 *	unsigned char *src, int len)
 *
 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
 *	src
 * 
 * Inputs : src = source, len = length in bytes
 *
 * Returns : 0 on success, non zero on a failure such as a watchdog 
 * 	timeout.
*/

static inline int dtc_pwrite(struct Scsi_Host *instance,
                             unsigned char *src, int len)
{
	int i;
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	if (instance->irq == NO_IRQ)
		NCR5380_write(DTC_CONTROL_REG, 0);
	else
		NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);
	NCR5380_write(DTC_BLK_CNT, len >> 7);	/* Block count */
	for (i = 0; len > 0; ++i) {
		rtrc(5);
		/* Poll until the host buffer can accept data. */
		while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
			++i;
		rtrc(3);
		memcpy_toio(hostdata->base + DTC_DATA_BUF, src, 128);
		src += 128;
		len -= 128;
	}
	rtrc(4);
	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
		++i;
	rtrc(6);
	/* Wait until the last byte has been sent to the disk */
	while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
		++i;
	rtrc(7);
	/* Check for parity error here. fixme. */
	rtrc(0);
	return (0);
}

static int dtc_dma_xfer_len(struct scsi_cmnd *cmd)
{
	int transfersize = cmd->transfersize;

	/* Limit transfers to 32K, for xx400 & xx406
	 * pseudoDMA that transfers in 128 bytes blocks.
	 */
	if (transfersize > 32 * 1024 && cmd->SCp.this_residual &&
	    !(cmd->SCp.this_residual % transfersize))
		transfersize = 32 * 1024;

	return transfersize;
}

MODULE_LICENSE("GPL");

#include "NCR5380.c"

static int dtc_release(struct Scsi_Host *shost)
{
	struct NCR5380_hostdata *hostdata = shost_priv(shost);

	if (shost->irq != NO_IRQ)
		free_irq(shost->irq, shost);
	NCR5380_exit(shost);
	scsi_unregister(shost);
	iounmap(hostdata->base);
	return 0;
}

static struct scsi_host_template driver_template = {
	.name			= "DTC 3180/3280",
	.detect			= dtc_detect,
	.release		= dtc_release,
	.proc_name		= "dtc3x80",
	.info			= dtc_info,
	.queuecommand		= dtc_queue_command,
	.eh_abort_handler	= dtc_abort,
	.eh_bus_reset_handler	= dtc_bus_reset,
	.bios_param		= dtc_biosparam,
	.can_queue		= 32,
	.this_id		= 7,
	.sg_tablesize		= SG_ALL,
	.cmd_per_lun		= 2,
	.use_clustering		= DISABLE_CLUSTERING,
	.cmd_size		= NCR5380_CMD_SIZE,
	.max_sectors		= 128,
};
#include "scsi_module.c"
Commit	Line	Data
1da177e4 LT	1	/*
	2	* DTC 3180/3280 driver, by
	3	* Ray Van Tassle rayvt@comm.mot.com
	4	*
	5	* taken from ...
	6	* Trantor T128/T128F/T228 driver by...
	7	*
	8	* Drew Eckhardt
	9	* Visionary Computing
	10	* (Unix and Linux consulting and custom programming)
	11	* drew@colorado.edu
	12	* +1 (303) 440-4894
3f9e986e	13	*/
1da177e4 LT	14
1da177e4 LT	15	/*
1da177e4 LT	16	* The card is detected and initialized in one of several ways :
	17	* 1. Autoprobe (default) - since the board is memory mapped,
	18	* a BIOS signature is scanned for to locate the registers.
	19	* An interrupt is triggered to autoprobe for the interrupt
	20	* line.
	21	*
	22	* 2. With command line overrides - dtc=address,irq may be
	23	* used on the LILO command line to override the defaults.
	24	*
	25	*/
	26
	27	/----------------------------------------------------------------/
	28	/* the following will set the monitor border color (useful to find
	29	where something crashed or gets stuck at */
	30	/* 1 = blue
	31	2 = green
	32	3 = cyan
	33	4 = red
	34	5 = magenta
	35	6 = yellow
	36	7 = white
	37	*/
	38	#if 0
	39	#define rtrc(i) {inb(0x3da); outb(0x31, 0x3c0); outb((i), 0x3c0);}
	40	#else
	41	#define rtrc(i) {}
	42	#endif
	43
	44
1da177e4	45	#include <linux/module.h>
1da177e4	46	#include <linux/blkdev.h>
1da177e4 LT	47	#include <linux/string.h>
	48	#include <linux/init.h>
	49	#include <linux/interrupt.h>
53d5ed62	50	#include <linux/io.h>
1da177e4	51	#include <scsi/scsi_host.h>
161c0059	52
1da177e4	53	#include "dtc.h"
1da177e4 LT	54	#include "NCR5380.h"
1da177e4 LT	55
1da177e4 LT	56	/*
	57	* The DTC3180 & 3280 boards are memory mapped.
	58	*
	59	*/
	60
	61	/*
	62	*/
	63	/* Offset from DTC_5380_OFFSET */
	64	#define DTC_CONTROL_REG 0x100 /* rw */
	65	#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
	66	#define CSR_DIR_READ 0x40 /* rw direction, 1 = read 0 = write */
	67
	68	#define CSR_RESET 0x80 /* wo Resets 53c400 */
	69	#define CSR_5380_REG 0x80 /* ro 5380 registers can be accessed */
	70	#define CSR_TRANS_DIR 0x40 /* rw Data transfer direction */
	71	#define CSR_SCSI_BUFF_INTR 0x20 /* rw Enable int on transfer ready */
	72	#define CSR_5380_INTR 0x10 /* rw Enable 5380 interrupts */
	73	#define CSR_SHARED_INTR 0x08 /* rw Interrupt sharing */
	74	#define CSR_HOST_BUF_NOT_RDY 0x04 /* ro Host buffer not ready */
	75	#define CSR_SCSI_BUF_RDY 0x02 /* ro SCSI buffer ready */
	76	#define CSR_GATED_5380_IRQ 0x01 /* ro Last block xferred */
	77	#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR \| CSR_5380_INTR)
	78
	79
	80	#define DTC_BLK_CNT 0x101 /* rw
	81	* # of 128-byte blocks to transfer */
	82
	83
	84	#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
	85
	86	#define DTC_SWITCH_REG 0x3982 /* ro - DIP switches */
	87	#define DTC_RESUME_XFER 0x3982 /* wo - resume data xfer
	88	* after disconnect/reconnect*/
	89
	90	#define DTC_5380_OFFSET 0x3880 /* 8 registers here, see NCR5380.h */
	91
	92	/!!!! for dtc, it's a 128 byte buffer at 3900 !!! /
	93	#define DTC_DATA_BUF 0x3900 /* rw 128 bytes long */
	94
	95	static struct override {
	96	unsigned int address;
	97	int irq;
	98	} overrides
	99	#ifdef OVERRIDE
	100	[] __initdata = OVERRIDE;
	101	#else
1fbe8529 AC	102	[4] __initdata = {
	103	{ 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }
	104	};
1da177e4 LT	105	#endif
1da177e4 LT	106
6391a113	107	#define NO_OVERRIDES ARRAY_SIZE(overrides)
1da177e4 LT	108
	109	static struct base {
	110	unsigned long address;
	111	int noauto;
6391a113 TK	112	} bases[] __initdata = {
	113	{ 0xcc000, 0 },
	114	{ 0xc8000, 0 },
	115	{ 0xdc000, 0 },
1da177e4 LT	116	{ 0xd8000, 0 }
	117	};
	118
6391a113	119	#define NO_BASES ARRAY_SIZE(bases)
1da177e4 LT	120
	121	static const struct signature {
	122	const char *string;
	123	int offset;
6391a113	124	} signatures[] = {
1da177e4 LT	125	{"DATA TECHNOLOGY CORPORATION BIOS", 0x25},
	126	};
	127
6391a113	128	#define NO_SIGNATURES ARRAY_SIZE(signatures)
1da177e4 LT	129
	130	#ifndef MODULE
	131	/*
	132	* Function : dtc_setup(char str, int ints)
	133	*
	134	* Purpose : LILO command line initialization of the overrides array,
6391a113	135	*
1da177e4 LT	136	* Inputs : str - unused, ints - array of integer parameters with ints[0]
	137	* equal to the number of ints.
	138	*
1fbe8529	139	*/
1da177e4	140
925e4610	141	static int __init dtc_setup(char *str)
1da177e4	142	{
d5f7e65d	143	static int commandline_current;
1da177e4	144	int i;
925e4610 FT	145	int ints[10];
	146
	147	get_options(str, ARRAY_SIZE(ints), ints);
1da177e4 LT	148	if (ints[0] != 2)
	149	printk("dtc_setup: usage dtc=address,irq\n");
	150	else if (commandline_current < NO_OVERRIDES) {
	151	overrides[commandline_current].address = ints[1];
	152	overrides[commandline_current].irq = ints[2];
	153	for (i = 0; i < NO_BASES; ++i)
	154	if (bases[i].address == ints[1]) {
	155	bases[i].noauto = 1;
	156	break;
	157	}
	158	++commandline_current;
	159	}
925e4610	160	return 1;
1da177e4	161	}
925e4610 FT	162
925e4610 FT	163	__setup("dtc=", dtc_setup);
1da177e4 LT	164	#endif
	165
	166	/*
d0be4a7d	167	* Function : int dtc_detect(struct scsi_host_template * tpnt)
1da177e4 LT	168	*
	169	* Purpose : detects and initializes DTC 3180/3280 controllers
	170	* that were autoprobed, overridden on the LILO command line,
	171	* or specified at compile time.
	172	*
	173	* Inputs : tpnt - template for this SCSI adapter.
	174	*
	175	* Returns : 1 if a host adapter was found, 0 if not.
	176	*
	177	*/
	178
d0be4a7d	179	static int __init dtc_detect(struct scsi_host_template * tpnt)
1da177e4	180	{
d5f7e65d	181	static int current_override, current_base;
1da177e4 LT	182	struct Scsi_Host *instance;
	183	unsigned int addr;
	184	void __iomem *base;
	185	int sig, count;
	186
1da177e4 LT	187	for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
	188	addr = 0;
	189	base = NULL;
	190
	191	if (overrides[current_override].address) {
	192	addr = overrides[current_override].address;
	193	base = ioremap(addr, 0x2000);
	194	if (!base)
	195	addr = 0;
	196	} else
	197	for (; !addr && (current_base < NO_BASES); ++current_base) {
2f7dba9f FT	198	dprintk(NDEBUG_INIT, "dtc: probing address 0x%08x\n",
2f7dba9f FT	199	(unsigned int)bases[current_base].address);
1da177e4 LT	200	if (bases[current_base].noauto)
	201	continue;
	202	base = ioremap(bases[current_base].address, 0x2000);
	203	if (!base)
	204	continue;
	205	for (sig = 0; sig < NO_SIGNATURES; ++sig) {
	206	if (check_signature(base + signatures[sig].offset, signatures[sig].string, strlen(signatures[sig].string))) {
	207	addr = bases[current_base].address;
2f7dba9f	208	dprintk(NDEBUG_INIT, "dtc: detected board\n");
1da177e4 LT	209	goto found;
	210	}
	211	}
	212	iounmap(base);
	213	}
	214
2f7dba9f	215	dprintk(NDEBUG_INIT, "dtc: addr = 0x%08x\n", addr);
1da177e4 LT	216
	217	if (!addr)
	218	break;
	219
	220	found:
	221	instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
	222	if (instance == NULL)
0ad0eff9	223	goto out_unmap;
1da177e4 LT	224
	225	instance->base = addr;
	226	((struct NCR5380_hostdata *)(instance)->hostdata)->base = base;
	227
8053b0ee	228	if (NCR5380_init(instance, FLAG_LATE_DMA_SETUP))
0ad0eff9	229	goto out_unregister;
1da177e4	230
b6488f97 FT	231	NCR5380_maybe_reset_bus(instance);
b6488f97 FT	232
1da177e4 LT	233	NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR); /* Enable int's */
	234	if (overrides[current_override].irq != IRQ_AUTO)
	235	instance->irq = overrides[current_override].irq;
	236	else
	237	instance->irq = NCR5380_probe_irq(instance, DTC_IRQS);
	238
22f5f10d FT	239	/* Compatibility with documented NCR5380 kernel parameters */
	240	if (instance->irq == 255)
	241	instance->irq = NO_IRQ;
	242
1da177e4 LT	243	/* With interrupts enabled, it will sometimes hang when doing heavy
1da177e4 LT	244	* reads. So better not enable them until I finger it out. */
a46865dc FT	245	instance->irq = NO_IRQ;
a46865dc FT	246
22f5f10d	247	if (instance->irq != NO_IRQ)
4909cc2b	248	if (request_irq(instance->irq, dtc_intr, 0,
1e641664	249	"dtc", instance)) {
1da177e4	250	printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
22f5f10d	251	instance->irq = NO_IRQ;
1da177e4 LT	252	}
1da177e4 LT	253
22f5f10d	254	if (instance->irq == NO_IRQ) {
1da177e4 LT	255	printk(KERN_WARNING "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
	256	printk(KERN_WARNING "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
	257	}
a46865dc	258
2f7dba9f FT	259	dprintk(NDEBUG_INIT, "scsi%d : irq = %d\n",
2f7dba9f FT	260	instance->host_no, instance->irq);
1da177e4	261
1da177e4 LT	262	++current_override;
	263	++count;
	264	}
	265	return count;
0ad0eff9 FT	266
	267	out_unregister:
	268	scsi_unregister(instance);
	269	out_unmap:
	270	iounmap(base);
	271	return count;
1da177e4 LT	272	}
	273
	274	/*
	275	* Function : int dtc_biosparam(Disk * disk, struct block_device dev, int ip)
	276	*
	277	* Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
	278	* the specified device / size.
	279	*
	280	* Inputs : size = size of device in sectors (512 bytes), dev = block device
	281	* major / minor, ip[] = {heads, sectors, cylinders}
	282	*
	283	* Returns : always 0 (success), initializes ip
	284	*
	285	*/
	286
	287	/*
	288	* XXX Most SCSI boards use this mapping, I could be incorrect. Some one
	289	* using hard disks on a trantor should verify that this mapping corresponds
	290	* to that used by the BIOS / ASPI driver by running the linux fdisk program
	291	* and matching the H_C_S coordinates to what DOS uses.
	292	*/
	293
	294	static int dtc_biosparam(struct scsi_device sdev, struct block_device dev,
	295	sector_t capacity, int *ip)
	296	{
	297	int size = capacity;
	298
	299	ip[0] = 64;
	300	ip[1] = 32;
	301	ip[2] = size >> 11;
	302	return 0;
	303	}
	304
	305
	306	/****************************************************************
	307	* Function : int NCR5380_pread (struct Scsi_Host *instance,
	308	* unsigned char *dst, int len)
	309	*
	310	* Purpose : Fast 5380 pseudo-dma read function, reads len bytes to
	311	* dst
	312	*
	313	* Inputs : dst = destination, len = length in bytes
	314	*
	315	* Returns : 0 on success, non zero on a failure such as a watchdog
	316	* timeout.
	317	*/
	318
6c4b88ca FT	319	static inline int dtc_pread(struct Scsi_Host *instance,
6c4b88ca FT	320	unsigned char *dst, int len)
1da177e4 LT	321	{
	322	unsigned char *d = dst;
	323	int i; /* For counting time spent in the poll-loop */
a9c2dc43	324	struct NCR5380_hostdata *hostdata = shost_priv(instance);
1da177e4 LT	325
1da177e4 LT	326	i = 0;
22f5f10d	327	if (instance->irq == NO_IRQ)
1da177e4 LT	328	NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
	329	else
	330	NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ \| CSR_INT_BASE);
	331	NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
	332	rtrc(1);
	333	while (len > 0) {
	334	rtrc(2);
	335	while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
	336	++i;
	337	rtrc(3);
54d8fe44	338	memcpy_fromio(d, hostdata->base + DTC_DATA_BUF, 128);
1da177e4 LT	339	d += 128;
	340	len -= 128;
	341	rtrc(7);
	342	/*** with int's on, it sometimes hangs after here.
	343	* Looks like something makes HBNR go away. */
	344	}
	345	rtrc(4);
	346	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
	347	++i;
1da177e4	348	rtrc(0);
1da177e4 LT	349	return (0);
	350	}
	351
	352	/****************************************************************
	353	* Function : int NCR5380_pwrite (struct Scsi_Host *instance,
	354	* unsigned char *src, int len)
	355	*
	356	* Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
	357	* src
	358	*
	359	* Inputs : src = source, len = length in bytes
	360	*
	361	* Returns : 0 on success, non zero on a failure such as a watchdog
	362	* timeout.
	363	*/
	364
6c4b88ca FT	365	static inline int dtc_pwrite(struct Scsi_Host *instance,
6c4b88ca FT	366	unsigned char *src, int len)
1da177e4 LT	367	{
1da177e4 LT	368	int i;
a9c2dc43	369	struct NCR5380_hostdata *hostdata = shost_priv(instance);
1da177e4	370
22f5f10d	371	if (instance->irq == NO_IRQ)
1da177e4 LT	372	NCR5380_write(DTC_CONTROL_REG, 0);
	373	else
	374	NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);
	375	NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
	376	for (i = 0; len > 0; ++i) {
	377	rtrc(5);
	378	/* Poll until the host buffer can accept data. */
	379	while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
	380	++i;
	381	rtrc(3);
54d8fe44	382	memcpy_toio(hostdata->base + DTC_DATA_BUF, src, 128);
1da177e4 LT	383	src += 128;
	384	len -= 128;
	385	}
	386	rtrc(4);
	387	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
	388	++i;
	389	rtrc(6);
	390	/* Wait until the last byte has been sent to the disk */
	391	while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
	392	++i;
	393	rtrc(7);
	394	/* Check for parity error here. fixme. */
1da177e4	395	rtrc(0);
1da177e4 LT	396	return (0);
	397	}
	398
ff3d4578 FT	399	static int dtc_dma_xfer_len(struct scsi_cmnd *cmd)
	400	{
	401	int transfersize = cmd->transfersize;
	402
	403	/* Limit transfers to 32K, for xx400 & xx406
	404	* pseudoDMA that transfers in 128 bytes blocks.
	405	*/
	406	if (transfersize > 32 * 1024 && cmd->SCp.this_residual &&
	407	!(cmd->SCp.this_residual % transfersize))
	408	transfersize = 32 * 1024;
	409
	410	return transfersize;
	411	}
	412
1da177e4 LT	413	MODULE_LICENSE("GPL");
	414
	415	#include "NCR5380.c"
	416
	417	static int dtc_release(struct Scsi_Host *shost)
	418	{
54d8fe44 FT	419	struct NCR5380_hostdata *hostdata = shost_priv(shost);
54d8fe44 FT	420
22f5f10d	421	if (shost->irq != NO_IRQ)
1e641664	422	free_irq(shost->irq, shost);
1da177e4	423	NCR5380_exit(shost);
1da177e4	424	scsi_unregister(shost);
54d8fe44	425	iounmap(hostdata->base);
1da177e4 LT	426	return 0;
	427	}
	428
d0be4a7d	429	static struct scsi_host_template driver_template = {
aa2e2cb1 FT	430	.name = "DTC 3180/3280",
	431	.detect = dtc_detect,
	432	.release = dtc_release,
	433	.proc_name = "dtc3x80",
aa2e2cb1 FT	434	.info = dtc_info,
	435	.queuecommand = dtc_queue_command,
	436	.eh_abort_handler = dtc_abort,
	437	.eh_bus_reset_handler = dtc_bus_reset,
	438	.bios_param = dtc_biosparam,
	439	.can_queue = 32,
	440	.this_id = 7,
	441	.sg_tablesize = SG_ALL,
	442	.cmd_per_lun = 2,
	443	.use_clustering = DISABLE_CLUSTERING,
32b26a10	444	.cmd_size = NCR5380_CMD_SIZE,
0a4e3612	445	.max_sectors = 128,
1da177e4 LT	446	};
1da177e4 LT	447	#include "scsi_module.c"