[linux-2.6-block.git] / drivers / net / Kconfig

#
# Network device configuration
#

menuconfig NETDEVICES
	default y if UML
	depends on NET
	bool "Network device support"
	---help---
	  You can say N here if you don't intend to connect your Linux box to
	  any other computer at all.

	  You'll have to say Y if your computer contains a network card that
	  you want to use under Linux. If you are going to run SLIP or PPP over
	  telephone line or null modem cable you need say Y here. Connecting
	  two machines with parallel ports using PLIP needs this, as well as
	  AX.25/KISS for sending Internet traffic over amateur radio links.

	  See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	  Terry Dawson. Available at <http://www.tldp.org/guides.html>.

	  If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config NET_CORE
	default y
	bool "Network core driver support"
	---help---
	  You can say N here if you do not intend to use any of the
	  networking core drivers (i.e. VLAN, bridging, bonding, etc.)

if NET_CORE

config BONDING
	tristate "Bonding driver support"
	depends on INET
	depends on IPV6 || IPV6=n
	---help---
	  Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	  Channels together. This is called 'Etherchannel' by Cisco,
	  'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

	  The driver supports multiple bonding modes to allow for both high
	  performance and high availability operation.

	  Refer to <file:Documentation/networking/bonding.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called bonding.

config DUMMY
	tristate "Dummy net driver support"
	---help---
	  This is essentially a bit-bucket device (i.e. traffic you send to
	  this device is consigned into oblivion) with a configurable IP
	  address. It is most commonly used in order to make your currently
	  inactive SLIP address seem like a real address for local programs.
	  If you use SLIP or PPP, you might want to say Y here. Since this
	  thing often comes in handy, the default is Y. It won't enlarge your
	  kernel either. What a deal. Read about it in the Network
	  Administrator's Guide, available from
	  <http://www.tldp.org/docs.html#guide>.

	  To compile this driver as a module, choose M here: the module
	  will be called dummy.  If you want to use more than one dummy
	  device at a time, you need to compile this driver as a module.
	  Instead of 'dummy', the devices will then be called 'dummy0',
	  'dummy1' etc.

config EQUALIZER
	tristate "EQL (serial line load balancing) support"
	---help---
	  If you have two serial connections to some other computer (this
	  usually requires two modems and two telephone lines) and you use
	  SLIP (the protocol for sending Internet traffic over telephone
	  lines) or PPP (a better SLIP) on them, you can make them behave like
	  one double speed connection using this driver.  Naturally, this has
	  to be supported at the other end as well, either with a similar EQL
	  Linux driver or with a Livingston Portmaster 2e.

	  Say Y if you want this and read
	  <file:Documentation/networking/eql.txt>.  You may also want to read
	  section 6.2 of the NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called eql.  If unsure, say N.

config NET_FC
	bool "Fibre Channel driver support"
	depends on SCSI && PCI
	help
	  Fibre Channel is a high speed serial protocol mainly used to connect
	  large storage devices to the computer; it is compatible with and
	  intended to replace SCSI.

	  If you intend to use Fibre Channel, you need to have a Fibre channel
	  adaptor card in your computer; say Y here and to the driver for your
	  adaptor below. You also should have said Y to "SCSI support" and
	  "SCSI generic support".

config MII
	tristate "Generic Media Independent Interface device support"
	help
	  Most ethernet controllers have MII transceiver either as an external
	  or internal device.  It is safe to say Y or M here even if your
	  ethernet card lacks MII.

source "drivers/ieee802154/Kconfig"

config IFB
	tristate "Intermediate Functional Block support"
	depends on NET_CLS_ACT
	---help---
	  This is an intermediate driver that allows sharing of
	  resources.
	  To compile this driver as a module, choose M here: the module
	  will be called ifb.  If you want to use more than one ifb
	  device at a time, you need to compile this driver as a module.
	  Instead of 'ifb', the devices will then be called 'ifb0',
	  'ifb1' etc.
	  Look at the iproute2 documentation directory for usage etc

source "drivers/net/team/Kconfig"

config MACVLAN
	tristate "MAC-VLAN support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	---help---
	  This allows one to create virtual interfaces that map packets to
	  or from specific MAC addresses to a particular interface.

	  Macvlan devices can be added using the "ip" command from the
	  iproute2 package starting with the iproute2-2.6.23 release:

	  "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"

	  To compile this driver as a module, choose M here: the module
	  will be called macvlan.

config MACVTAP
	tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
	depends on MACVLAN
	help
	  This adds a specialized tap character device driver that is based
	  on the MAC-VLAN network interface, called macvtap. A macvtap device
	  can be added in the same way as a macvlan device, using 'type
	  macvlan', and then be accessed through the tap user space interface.

	  To compile this driver as a module, choose M here: the module
	  will be called macvtap.

config NETCONSOLE
	tristate "Network console logging support"
	---help---
	If you want to log kernel messages over the network, enable this.
	See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
	bool "Dynamic reconfiguration of logging targets"
	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
			!(NETCONSOLE=y && CONFIGFS_FS=m)
	help
	  This option enables the ability to dynamically reconfigure target
	  parameters (interface, IP addresses, port numbers, MAC addresses)
	  at runtime through a userspace interface exported using configfs.
	  See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
	def_bool NETCONSOLE

config NETPOLL_TRAP
	bool "Netpoll traffic trapping"
	default n
	depends on NETPOLL

config NET_POLL_CONTROLLER
	def_bool NETPOLL

config RIONET
	tristate "RapidIO Ethernet over messaging driver support"
	depends on RAPIDIO

config RIONET_TX_SIZE
	int "Number of outbound queue entries"
	depends on RIONET
	default "128"

config RIONET_RX_SIZE
	int "Number of inbound queue entries"
	depends on RIONET
	default "128"

config TUN
	tristate "Universal TUN/TAP device driver support"
	select CRC32
	---help---
	  TUN/TAP provides packet reception and transmission for user space
	  programs.  It can be viewed as a simple Point-to-Point or Ethernet
	  device, which instead of receiving packets from a physical media,
	  receives them from user space program and instead of sending packets
	  via physical media writes them to the user space program.

	  When a program opens /dev/net/tun, driver creates and registers
	  corresponding net device tunX or tapX.  After a program closed above
	  devices, driver will automatically delete tunXX or tapXX device and
	  all routes corresponding to it.

	  Please read <file:Documentation/networking/tuntap.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called tun.

	  If you don't know what to use this for, you don't need it.

config VETH
	tristate "Virtual ethernet pair device"
	---help---
	  This device is a local ethernet tunnel. Devices are created in pairs.
	  When one end receives the packet it appears on its pair and vice
	  versa.

config VIRTIO_NET
	tristate "Virtio network driver (EXPERIMENTAL)"
	depends on EXPERIMENTAL && VIRTIO
	---help---
	  This is the virtual network driver for virtio.  It can be used with
	  lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.

endif # NET_CORE

config SUNGEM_PHY
	tristate

source "drivers/net/arcnet/Kconfig"

source "drivers/atm/Kconfig"

source "drivers/net/caif/Kconfig"

source "drivers/net/dsa/Kconfig"

source "drivers/net/ethernet/Kconfig"

source "drivers/net/fddi/Kconfig"

source "drivers/net/hippi/Kconfig"

config NET_SB1000
	tristate "General Instruments Surfboard 1000"
	depends on PNP
	---help---
	  This is a driver for the General Instrument (also known as
	  NextLevel) SURFboard 1000 internal
	  cable modem. This is an ISA card which is used by a number of cable
	  TV companies to provide cable modem access. It's a one-way
	  downstream-only cable modem, meaning that your upstream net link is
	  provided by your regular phone modem.

	  At present this driver only compiles as a module, so say M here if
	  you have this card. The module will be called sb1000. Then read
	  <file:Documentation/networking/README.sb1000> for information on how
	  to use this module, as it needs special ppp scripts for establishing
	  a connection. Further documentation and the necessary scripts can be
	  found at:

	  <http://www.jacksonville.net/~fventuri/>
	  <http://home.adelphia.net/~siglercm/sb1000.html>
	  <http://linuxpower.cx/~cable/>

	  If you don't have this card, of course say N.

source "drivers/net/phy/Kconfig"

source "drivers/net/plip/Kconfig"

source "drivers/net/ppp/Kconfig"

source "drivers/net/slip/Kconfig"

source "drivers/s390/net/Kconfig"

source "drivers/net/tokenring/Kconfig"

source "drivers/net/usb/Kconfig"

source "drivers/net/wireless/Kconfig"

source "drivers/net/wimax/Kconfig"

source "drivers/net/wan/Kconfig"

config XEN_NETDEV_FRONTEND
	tristate "Xen network device frontend driver"
	depends on XEN
	select XEN_XENBUS_FRONTEND
	default y
	help
	  This driver provides support for Xen paravirtual network
	  devices exported by a Xen network driver domain (often
	  domain 0).

	  The corresponding Linux backend driver is enabled by the
	  CONFIG_XEN_NETDEV_BACKEND option.

	  If you are compiling a kernel for use as Xen guest, you
	  should say Y here. To compile this driver as a module, chose
	  M here: the module will be called xen-netfront.

config XEN_NETDEV_BACKEND
	tristate "Xen backend network device"
	depends on XEN_BACKEND
	help
	  This driver allows the kernel to act as a Xen network driver
	  domain which exports paravirtual network devices to other
	  Xen domains. These devices can be accessed by any operating
	  system that implements a compatible front end.

	  The corresponding Linux frontend driver is enabled by the
	  CONFIG_XEN_NETDEV_FRONTEND configuration option.

	  The backend driver presents a standard network device
	  endpoint for each paravirtual network device to the driver
	  domain network stack. These can then be bridged or routed
	  etc in order to provide full network connectivity.

	  If you are compiling a kernel to run in a Xen network driver
	  domain (often this is domain 0) you should say Y here. To
	  compile this driver as a module, chose M here: the module
	  will be called xen-netback.

config VMXNET3
	tristate "VMware VMXNET3 ethernet driver"
	depends on PCI && INET
	help
	  This driver supports VMware's vmxnet3 virtual ethernet NIC.
	  To compile this driver as a module, choose M here: the
	  module will be called vmxnet3.

source "drivers/net/hyperv/Kconfig"

endif # NETDEVICES
Commit	Line	Data
1da177e4 LT	1	#
	2	# Network device configuration
	3	#
	4
d1c0a65f	5	menuconfig NETDEVICES
ce2d2aed	6	default y if UML
e0009820	7	depends on NET
1da177e4 LT	8	bool "Network device support"
	9	---help---
	10	You can say N here if you don't intend to connect your Linux box to
	11	any other computer at all.
	12
	13	You'll have to say Y if your computer contains a network card that
	14	you want to use under Linux. If you are going to run SLIP or PPP over
	15	telephone line or null modem cable you need say Y here. Connecting
	16	two machines with parallel ports using PLIP needs this, as well as
	17	AX.25/KISS for sending Internet traffic over amateur radio links.
	18
	19	See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	20	Terry Dawson. Available at <http://www.tldp.org/guides.html>.
	21
	22	If unsure, say Y.
	23
1618cb0c RD	24	# All the following symbols are dependent on NETDEVICES - do not repeat
	25	# that for each of the symbols.
	26	if NETDEVICES
cbcd2a4c	27
88491d81 JK	28	config NET_CORE
	29	default y
	30	bool "Network core driver support"
253af423	31	---help---
88491d81 JK	32	You can say N here if you do not intend to use any of the
	33	networking core drivers (i.e. VLAN, bridging, bonding, etc.)
	34
	35	if NET_CORE
	36
	37	config BONDING
	38	tristate "Bonding driver support"
	39	depends on INET
	40	depends on IPV6 \|\| IPV6=n
	41	---help---
	42	Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	43	Channels together. This is called 'Etherchannel' by Cisco,
	44	'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
	45
	46	The driver supports multiple bonding modes to allow for both high
	47	performance and high availability operation.
	48
	49	Refer to <file:Documentation/networking/bonding.txt> for more
	50	information.
	51
253af423	52	To compile this driver as a module, choose M here: the module
88491d81	53	will be called bonding.
253af423	54
1da177e4 LT	55	config DUMMY
1da177e4 LT	56	tristate "Dummy net driver support"
1da177e4 LT	57	---help---
	58	This is essentially a bit-bucket device (i.e. traffic you send to
	59	this device is consigned into oblivion) with a configurable IP
	60	address. It is most commonly used in order to make your currently
	61	inactive SLIP address seem like a real address for local programs.
	62	If you use SLIP or PPP, you might want to say Y here. Since this
	63	thing often comes in handy, the default is Y. It won't enlarge your
	64	kernel either. What a deal. Read about it in the Network
	65	Administrator's Guide, available from
	66	<http://www.tldp.org/docs.html#guide>.
	67
	68	To compile this driver as a module, choose M here: the module
	69	will be called dummy. If you want to use more than one dummy
	70	device at a time, you need to compile this driver as a module.
	71	Instead of 'dummy', the devices will then be called 'dummy0',
	72	'dummy1' etc.
	73
88491d81 JK	74	config EQUALIZER
88491d81 JK	75	tristate "EQL (serial line load balancing) support"
1da177e4	76	---help---
88491d81 JK	77	If you have two serial connections to some other computer (this
	78	usually requires two modems and two telephone lines) and you use
	79	SLIP (the protocol for sending Internet traffic over telephone
	80	lines) or PPP (a better SLIP) on them, you can make them behave like
	81	one double speed connection using this driver. Naturally, this has
	82	to be supported at the other end as well, either with a similar EQL
	83	Linux driver or with a Livingston Portmaster 2e.
1da177e4	84
88491d81 JK	85	Say Y if you want this and read
	86	<file:Documentation/networking/eql.txt>. You may also want to read
	87	section 6.2 of the NET-3-HOWTO, available from
	88	<http://www.tldp.org/docs.html#howto>.
1da177e4	89
88491d81 JK	90	To compile this driver as a module, choose M here: the module
	91	will be called eql. If unsure, say N.
	92
	93	config NET_FC
	94	bool "Fibre Channel driver support"
	95	depends on SCSI && PCI
	96	help
	97	Fibre Channel is a high speed serial protocol mainly used to connect
	98	large storage devices to the computer; it is compatible with and
	99	intended to replace SCSI.
	100
	101	If you intend to use Fibre Channel, you need to have a Fibre channel
	102	adaptor card in your computer; say Y here and to the driver for your
	103	adaptor below. You also should have said Y to "SCSI support" and
	104	"SCSI generic support".
1da177e4	105
88491d81 JK	106	config MII
	107	tristate "Generic Media Independent Interface device support"
	108	help
	109	Most ethernet controllers have MII transceiver either as an external
	110	or internal device. It is safe to say Y or M here even if your
	111	ethernet card lacks MII.
	112
	113	source "drivers/ieee802154/Kconfig"
	114
	115	config IFB
	116	tristate "Intermediate Functional Block support"
	117	depends on NET_CLS_ACT
	118	---help---
	119	This is an intermediate driver that allows sharing of
	120	resources.
1da177e4	121	To compile this driver as a module, choose M here: the module
88491d81 JK	122	will be called ifb. If you want to use more than one ifb
	123	device at a time, you need to compile this driver as a module.
	124	Instead of 'ifb', the devices will then be called 'ifb0',
	125	'ifb1' etc.
	126	Look at the iproute2 documentation directory for usage etc
1da177e4	127
3d249d4c JP	128	source "drivers/net/team/Kconfig"
3d249d4c JP	129
b863ceb7 PM	130	config MACVLAN
	131	tristate "MAC-VLAN support (EXPERIMENTAL)"
	132	depends on EXPERIMENTAL
	133	---help---
	134	This allows one to create virtual interfaces that map packets to
	135	or from specific MAC addresses to a particular interface.
	136
3dbf8d56 PM	137	Macvlan devices can be added using the "ip" command from the
	138	iproute2 package starting with the iproute2-2.6.23 release:
	139
	140	"ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
	141
b863ceb7 PM	142	To compile this driver as a module, choose M here: the module
	143	will be called macvlan.
	144
20d29d7a AB	145	config MACVTAP
	146	tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
	147	depends on MACVLAN
	148	help
	149	This adds a specialized tap character device driver that is based
	150	on the MAC-VLAN network interface, called macvtap. A macvtap device
	151	can be added in the same way as a macvlan device, using 'type
	152	macvlan', and then be accessed through the tap user space interface.
	153
	154	To compile this driver as a module, choose M here: the module
	155	will be called macvtap.
	156
88491d81 JK	157	config NETCONSOLE
88491d81 JK	158	tristate "Network console logging support"
1da177e4	159	---help---
88491d81 JK	160	If you want to log kernel messages over the network, enable this.
88491d81 JK	161	See <file:Documentation/networking/netconsole.txt> for details.
1da177e4	162
88491d81 JK	163	config NETCONSOLE_DYNAMIC
	164	bool "Dynamic reconfiguration of logging targets"
	165	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
	166	!(NETCONSOLE=y && CONFIGFS_FS=m)
	167	help
	168	This option enables the ability to dynamically reconfigure target
	169	parameters (interface, IP addresses, port numbers, MAC addresses)
	170	at runtime through a userspace interface exported using configfs.
	171	See <file:Documentation/networking/netconsole.txt> for details.
1da177e4	172
88491d81 JK	173	config NETPOLL
	174	def_bool NETCONSOLE
	175
	176	config NETPOLL_TRAP
	177	bool "Netpoll traffic trapping"
	178	default n
	179	depends on NETPOLL
	180
	181	config NET_POLL_CONTROLLER
	182	def_bool NETPOLL
	183
	184	config RIONET
	185	tristate "RapidIO Ethernet over messaging driver support"
	186	depends on RAPIDIO
	187
	188	config RIONET_TX_SIZE
	189	int "Number of outbound queue entries"
	190	depends on RIONET
	191	default "128"
	192
	193	config RIONET_RX_SIZE
	194	int "Number of inbound queue entries"
	195	depends on RIONET
	196	default "128"
1da177e4 LT	197
	198	config TUN
	199	tristate "Universal TUN/TAP device driver support"
1da177e4 LT	200	select CRC32
	201	---help---
	202	TUN/TAP provides packet reception and transmission for user space
	203	programs. It can be viewed as a simple Point-to-Point or Ethernet
	204	device, which instead of receiving packets from a physical media,
	205	receives them from user space program and instead of sending packets
	206	via physical media writes them to the user space program.
	207
	208	When a program opens /dev/net/tun, driver creates and registers
	209	corresponding net device tunX or tapX. After a program closed above
	210	devices, driver will automatically delete tunXX or tapXX device and
	211	all routes corresponding to it.
	212
	213	Please read <file:Documentation/networking/tuntap.txt> for more
	214	information.
	215
	216	To compile this driver as a module, choose M here: the module
	217	will be called tun.
	218
	219	If you don't know what to use this for, you don't need it.
	220
e314dbdc	221	config VETH
6a9a0250	222	tristate "Virtual ethernet pair device"
e314dbdc	223	---help---
6a9a0250 RR	224	This device is a local ethernet tunnel. Devices are created in pairs.
	225	When one end receives the packet it appears on its pair and vice
	226	versa.
e314dbdc	227
88491d81 JK	228	config VIRTIO_NET
	229	tristate "Virtio network driver (EXPERIMENTAL)"
	230	depends on EXPERIMENTAL && VIRTIO
	231	---help---
	232	This is the virtual network driver for virtio. It can be used with
	233	lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
	234
	235	endif # NET_CORE
	236
	237	config SUNGEM_PHY
	238	tristate
	239
	240	source "drivers/net/arcnet/Kconfig"
	241
	242	source "drivers/atm/Kconfig"
	243
	244	source "drivers/net/caif/Kconfig"
	245
3b158859 BH	246	source "drivers/net/dsa/Kconfig"
3b158859 BH	247
88491d81 JK	248	source "drivers/net/ethernet/Kconfig"
	249
	250	source "drivers/net/fddi/Kconfig"
	251
fecc7351 PB	252	source "drivers/net/hippi/Kconfig"
fecc7351 PB	253
1da177e4 LT	254	config NET_SB1000
1da177e4 LT	255	tristate "General Instruments Surfboard 1000"
cbcd2a4c	256	depends on PNP
1da177e4 LT	257	---help---
	258	This is a driver for the General Instrument (also known as
	259	NextLevel) SURFboard 1000 internal
	260	cable modem. This is an ISA card which is used by a number of cable
	261	TV companies to provide cable modem access. It's a one-way
	262	downstream-only cable modem, meaning that your upstream net link is
	263	provided by your regular phone modem.
	264
	265	At present this driver only compiles as a module, so say M here if
	266	you have this card. The module will be called sb1000. Then read
	267	<file:Documentation/networking/README.sb1000> for information on how
	268	to use this module, as it needs special ppp scripts for establishing
	269	a connection. Further documentation and the necessary scripts can be
	270	found at:
	271
	272	<http://www.jacksonville.net/~fventuri/>
	273	<http://home.adelphia.net/~siglercm/sb1000.html>
	274	<http://linuxpower.cx/~cable/>
	275
	276	If you don't have this card, of course say N.
	277
00db8189 AF	278	source "drivers/net/phy/Kconfig"
00db8189 AF	279
18e635f4 JK	280	source "drivers/net/plip/Kconfig"
18e635f4 JK	281
88491d81 JK	282	source "drivers/net/ppp/Kconfig"
88491d81 JK	283
b5451d78 JK	284	source "drivers/net/slip/Kconfig"
b5451d78 JK	285
88491d81 JK	286	source "drivers/s390/net/Kconfig"
88491d81 JK	287
1da177e4 LT	288	source "drivers/net/tokenring/Kconfig"
1da177e4 LT	289
88491d81 JK	290	source "drivers/net/usb/Kconfig"
88491d81 JK	291
1da177e4 LT	292	source "drivers/net/wireless/Kconfig"
1da177e4 LT	293
143ee2d5 IPG	294	source "drivers/net/wimax/Kconfig"
143ee2d5 IPG	295
1da177e4 LT	296	source "drivers/net/wan/Kconfig"
1da177e4 LT	297
0d160211 JF	298	config XEN_NETDEV_FRONTEND
	299	tristate "Xen network device frontend driver"
	300	depends on XEN
7003087c	301	select XEN_XENBUS_FRONTEND
0d160211 JF	302	default y
0d160211 JF	303	help
f942dc25 IC	304	This driver provides support for Xen paravirtual network
	305	devices exported by a Xen network driver domain (often
	306	domain 0).
	307
	308	The corresponding Linux backend driver is enabled by the
	309	CONFIG_XEN_NETDEV_BACKEND option.
	310
	311	If you are compiling a kernel for use as Xen guest, you
	312	should say Y here. To compile this driver as a module, chose
	313	M here: the module will be called xen-netfront.
	314
	315	config XEN_NETDEV_BACKEND
	316	tristate "Xen backend network device"
	317	depends on XEN_BACKEND
	318	help
	319	This driver allows the kernel to act as a Xen network driver
	320	domain which exports paravirtual network devices to other
	321	Xen domains. These devices can be accessed by any operating
	322	system that implements a compatible front end.
	323
	324	The corresponding Linux frontend driver is enabled by the
	325	CONFIG_XEN_NETDEV_FRONTEND configuration option.
	326
	327	The backend driver presents a standard network device
	328	endpoint for each paravirtual network device to the driver
	329	domain network stack. These can then be bridged or routed
	330	etc in order to provide full network connectivity.
	331
	332	If you are compiling a kernel to run in a Xen network driver
	333	domain (often this is domain 0) you should say Y here. To
	334	compile this driver as a module, chose M here: the module
	335	will be called xen-netback.
0d160211	336
d1a890fa	337	config VMXNET3
e85eb117 PDM	338	tristate "VMware VMXNET3 ethernet driver"
	339	depends on PCI && INET
	340	help
	341	This driver supports VMware's vmxnet3 virtual ethernet NIC.
	342	To compile this driver as a module, choose M here: the
	343	module will be called vmxnet3.
d1a890fa	344
95fa0405 HZ	345	source "drivers/net/hyperv/Kconfig"
95fa0405 HZ	346
d1c0a65f	347	endif # NETDEVICES