[linux-block.git] / drivers / md / Kconfig

#
# Block device driver configuration
#

menuconfig MD
	bool "Multiple devices driver support (RAID and LVM)"
	depends on BLOCK
	help
	  Support multiple physical spindles through a single logical device.
	  Required for RAID and logical volume management.

if MD

config BLK_DEV_MD
	tristate "RAID support"
	---help---
	  This driver lets you combine several hard disk partitions into one
	  logical block device. This can be used to simply append one
	  partition to another one or to combine several redundant hard disks
	  into a RAID1/4/5 device so as to provide protection against hard
	  disk failures. This is called "Software RAID" since the combining of
	  the partitions is done by the kernel. "Hardware RAID" means that the
	  combining is done by a dedicated controller; if you have such a
	  controller, you do not need to say Y here.

	  More information about Software RAID on Linux is contained in the
	  Software RAID mini-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. There you will also learn
	  where to get the supporting user space utilities raidtools.

	  If unsure, say N.

config MD_LINEAR
	tristate "Linear (append) mode"
	depends on BLK_DEV_MD
	---help---
	  If you say Y here, then your multiple devices driver will be able to
	  use the so-called linear mode, i.e. it will combine the hard disk
	  partitions by simply appending one to the other.

	  To compile this as a module, choose M here: the module
	  will be called linear.

	  If unsure, say Y.

config MD_RAID0
	tristate "RAID-0 (striping) mode"
	depends on BLK_DEV_MD
	---help---
	  If you say Y here, then your multiple devices driver will be able to
	  use the so-called raid0 mode, i.e. it will combine the hard disk
	  partitions into one logical device in such a fashion as to fill them
	  up evenly, one chunk here and one chunk there. This will increase
	  the throughput rate if the partitions reside on distinct disks.

	  Information about Software RAID on Linux is contained in the
	  Software-RAID mini-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. There you will also
	  learn where to get the supporting user space utilities raidtools.

	  To compile this as a module, choose M here: the module
	  will be called raid0.

	  If unsure, say Y.

config MD_RAID1
	tristate "RAID-1 (mirroring) mode"
	depends on BLK_DEV_MD
	---help---
	  A RAID-1 set consists of several disk drives which are exact copies
	  of each other.  In the event of a mirror failure, the RAID driver
	  will continue to use the operational mirrors in the set, providing
	  an error free MD (multiple device) to the higher levels of the
	  kernel.  In a set with N drives, the available space is the capacity
	  of a single drive, and the set protects against a failure of (N - 1)
	  drives.

	  Information about Software RAID on Linux is contained in the
	  Software-RAID mini-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  There you will also
	  learn where to get the supporting user space utilities raidtools.

	  If you want to use such a RAID-1 set, say Y.  To compile this code
	  as a module, choose M here: the module will be called raid1.

	  If unsure, say Y.

config MD_RAID10
	tristate "RAID-10 (mirrored striping) mode (EXPERIMENTAL)"
	depends on BLK_DEV_MD && EXPERIMENTAL
	---help---
	  RAID-10 provides a combination of striping (RAID-0) and
	  mirroring (RAID-1) with easier configuration and more flexible
	  layout.
	  Unlike RAID-0, but like RAID-1, RAID-10 requires all devices to
	  be the same size (or at least, only as much as the smallest device
	  will be used).
	  RAID-10 provides a variety of layouts that provide different levels
	  of redundancy and performance.

	  RAID-10 requires mdadm-1.7.0 or later, available at:

	  ftp://ftp.kernel.org/pub/linux/utils/raid/mdadm/

	  If unsure, say Y.

config MD_RAID456
	tristate "RAID-4/RAID-5/RAID-6 mode"
	depends on BLK_DEV_MD
	select ASYNC_MEMCPY
	select ASYNC_XOR
	---help---
	  A RAID-5 set of N drives with a capacity of C MB per drive provides
	  the capacity of C * (N - 1) MB, and protects against a failure
	  of a single drive. For a given sector (row) number, (N - 1) drives
	  contain data sectors, and one drive contains the parity protection.
	  For a RAID-4 set, the parity blocks are present on a single drive,
	  while a RAID-5 set distributes the parity across the drives in one
	  of the available parity distribution methods.

	  A RAID-6 set of N drives with a capacity of C MB per drive
	  provides the capacity of C * (N - 2) MB, and protects
	  against a failure of any two drives. For a given sector
	  (row) number, (N - 2) drives contain data sectors, and two
	  drives contains two independent redundancy syndromes.  Like
	  RAID-5, RAID-6 distributes the syndromes across the drives
	  in one of the available parity distribution methods.

	  Information about Software RAID on Linux is contained in the
	  Software-RAID mini-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. There you will also
	  learn where to get the supporting user space utilities raidtools.

	  If you want to use such a RAID-4/RAID-5/RAID-6 set, say Y.  To
	  compile this code as a module, choose M here: the module
	  will be called raid456.

	  If unsure, say Y.

config MD_RAID5_RESHAPE
	bool "Support adding drives to a raid-5 array"
	depends on MD_RAID456
	default y
	---help---
	  A RAID-5 set can be expanded by adding extra drives. This
	  requires "restriping" the array which means (almost) every
	  block must be written to a different place.

          This option allows such restriping to be done while the array
	  is online.

	  You will need mdadm version 2.4.1 or later to use this
	  feature safely.  During the early stage of reshape there is
	  a critical section where live data is being over-written.  A
	  crash during this time needs extra care for recovery.  The
	  newer mdadm takes a copy of the data in the critical section
	  and will restore it, if necessary, after a crash.

	  The mdadm usage is e.g.
	       mdadm --grow /dev/md1 --raid-disks=6
	  to grow '/dev/md1' to having 6 disks.

	  Note: The array can only be expanded, not contracted.
	  There should be enough spares already present to make the new
	  array workable.

	  If unsure, say Y.

config MD_MULTIPATH
	tristate "Multipath I/O support"
	depends on BLK_DEV_MD
	help
	  Multipath-IO is the ability of certain devices to address the same
	  physical disk over multiple 'IO paths'. The code ensures that such
	  paths can be defined and handled at runtime, and ensures that a
	  transparent failover to the backup path(s) happens if a IO errors
	  arrives on the primary path.

	  If unsure, say N.

config MD_FAULTY
	tristate "Faulty test module for MD"
	depends on BLK_DEV_MD
	help
	  The "faulty" module allows for a block device that occasionally returns
	  read or write errors.  It is useful for testing.

	  In unsure, say N.

config BLK_DEV_DM
	tristate "Device mapper support"
	---help---
	  Device-mapper is a low level volume manager.  It works by allowing
	  people to specify mappings for ranges of logical sectors.  Various
	  mapping types are available, in addition people may write their own
	  modules containing custom mappings if they wish.

	  Higher level volume managers such as LVM2 use this driver.

	  To compile this as a module, choose M here: the module will be
	  called dm-mod.

	  If unsure, say N.

config DM_DEBUG
	boolean "Device mapper debugging support"
	depends on BLK_DEV_DM && EXPERIMENTAL
	---help---
	  Enable this for messages that may help debug device-mapper problems.

	  If unsure, say N.

config DM_CRYPT
	tristate "Crypt target support"
	depends on BLK_DEV_DM && EXPERIMENTAL
	select CRYPTO
	select CRYPTO_CBC
	---help---
	  This device-mapper target allows you to create a device that
	  transparently encrypts the data on it. You'll need to activate
	  the ciphers you're going to use in the cryptoapi configuration.

	  Information on how to use dm-crypt can be found on

	  <http://www.saout.de/misc/dm-crypt/>

	  To compile this code as a module, choose M here: the module will
	  be called dm-crypt.

	  If unsure, say N.

config DM_SNAPSHOT
       tristate "Snapshot target (EXPERIMENTAL)"
       depends on BLK_DEV_DM && EXPERIMENTAL
       ---help---
         Allow volume managers to take writable snapshots of a device.

config DM_MIRROR
       tristate "Mirror target (EXPERIMENTAL)"
       depends on BLK_DEV_DM && EXPERIMENTAL
       ---help---
         Allow volume managers to mirror logical volumes, also
         needed for live data migration tools such as 'pvmove'.

config DM_ZERO
	tristate "Zero target (EXPERIMENTAL)"
	depends on BLK_DEV_DM && EXPERIMENTAL
	---help---
	  A target that discards writes, and returns all zeroes for
	  reads.  Useful in some recovery situations.

config DM_MULTIPATH
	tristate "Multipath target (EXPERIMENTAL)"
	depends on BLK_DEV_DM && EXPERIMENTAL
	---help---
	  Allow volume managers to support multipath hardware.

config DM_MULTIPATH_EMC
	tristate "EMC CX/AX multipath support (EXPERIMENTAL)"
	depends on DM_MULTIPATH && BLK_DEV_DM && EXPERIMENTAL
	---help---
	  Multipath support for EMC CX/AX series hardware.

config DM_MULTIPATH_RDAC
	tristate "LSI/Engenio RDAC multipath support (EXPERIMENTAL)"
	depends on DM_MULTIPATH && BLK_DEV_DM && SCSI && EXPERIMENTAL
	---help---
	  Multipath support for LSI/Engenio RDAC.

config DM_MULTIPATH_HP
        tristate "HP MSA multipath support (EXPERIMENTAL)"
        depends on DM_MULTIPATH && BLK_DEV_DM && EXPERIMENTAL
        ---help---
          Multipath support for HP MSA (Active/Passive) series hardware.

config DM_DELAY
	tristate "I/O delaying target (EXPERIMENTAL)"
	depends on BLK_DEV_DM && EXPERIMENTAL
	---help---
	A target that delays reads and/or writes and can send
	them to different devices.  Useful for testing.

	If unsure, say N.

endif # MD
Commit	Line	Data
1da177e4 LT	1	#
	2	# Block device driver configuration
	3	#
	4
afd44034	5	menuconfig MD
1da177e4	6	bool "Multiple devices driver support (RAID and LVM)"
afd44034	7	depends on BLOCK
1da177e4 LT	8	help
	9	Support multiple physical spindles through a single logical device.
	10	Required for RAID and logical volume management.
	11
afd44034 JE	12	if MD
afd44034 JE	13
1da177e4 LT	14	config BLK_DEV_MD
1da177e4 LT	15	tristate "RAID support"
1da177e4 LT	16	---help---
	17	This driver lets you combine several hard disk partitions into one
	18	logical block device. This can be used to simply append one
	19	partition to another one or to combine several redundant hard disks
	20	into a RAID1/4/5 device so as to provide protection against hard
	21	disk failures. This is called "Software RAID" since the combining of
	22	the partitions is done by the kernel. "Hardware RAID" means that the
	23	combining is done by a dedicated controller; if you have such a
	24	controller, you do not need to say Y here.
	25
	26	More information about Software RAID on Linux is contained in the
	27	Software RAID mini-HOWTO, available from
	28	<http://www.tldp.org/docs.html#howto>. There you will also learn
	29	where to get the supporting user space utilities raidtools.
	30
	31	If unsure, say N.
	32
	33	config MD_LINEAR
	34	tristate "Linear (append) mode"
	35	depends on BLK_DEV_MD
	36	---help---
	37	If you say Y here, then your multiple devices driver will be able to
	38	use the so-called linear mode, i.e. it will combine the hard disk
	39	partitions by simply appending one to the other.
	40
	41	To compile this as a module, choose M here: the module
	42	will be called linear.
	43
	44	If unsure, say Y.
	45
	46	config MD_RAID0
	47	tristate "RAID-0 (striping) mode"
	48	depends on BLK_DEV_MD
	49	---help---
	50	If you say Y here, then your multiple devices driver will be able to
	51	use the so-called raid0 mode, i.e. it will combine the hard disk
	52	partitions into one logical device in such a fashion as to fill them
	53	up evenly, one chunk here and one chunk there. This will increase
	54	the throughput rate if the partitions reside on distinct disks.
	55
	56	Information about Software RAID on Linux is contained in the
	57	Software-RAID mini-HOWTO, available from
	58	<http://www.tldp.org/docs.html#howto>. There you will also
	59	learn where to get the supporting user space utilities raidtools.
	60
	61	To compile this as a module, choose M here: the module
	62	will be called raid0.
	63
	64	If unsure, say Y.
	65
	66	config MD_RAID1
	67	tristate "RAID-1 (mirroring) mode"
	68	depends on BLK_DEV_MD
	69	---help---
	70	A RAID-1 set consists of several disk drives which are exact copies
	71	of each other. In the event of a mirror failure, the RAID driver
	72	will continue to use the operational mirrors in the set, providing
	73	an error free MD (multiple device) to the higher levels of the
	74	kernel. In a set with N drives, the available space is the capacity
	75	of a single drive, and the set protects against a failure of (N - 1)
	76	drives.
	77
	78	Information about Software RAID on Linux is contained in the
	79	Software-RAID mini-HOWTO, available from
80	<http://www.tldp.org/docs.html#howto>. There you will also
81	learn where to get the supporting user space utilities raidtools.
82
83	If you want to use such a RAID-1 set, say Y. To compile this code
84	as a module, choose M here: the module will be called raid1.
85
86	If unsure, say Y.
87
88	config MD_RAID10
89	tristate "RAID-10 (mirrored striping) mode (EXPERIMENTAL)"
90	depends on BLK_DEV_MD && EXPERIMENTAL
91	---help---
92	RAID-10 provides a combination of striping (RAID-0) and
4d2554d0	93	mirroring (RAID-1) with easier configuration and more flexible
1da177e4 LT	94	layout.
	95	Unlike RAID-0, but like RAID-1, RAID-10 requires all devices to
	96	be the same size (or at least, only as much as the smallest device
	97	will be used).
	98	RAID-10 provides a variety of layouts that provide different levels
	99	of redundancy and performance.
	100
	101	RAID-10 requires mdadm-1.7.0 or later, available at:
	102
	103	ftp://ftp.kernel.org/pub/linux/utils/raid/mdadm/
	104
	105	If unsure, say Y.
	106
16a53ecc N	107	config MD_RAID456
16a53ecc N	108	tristate "RAID-4/RAID-5/RAID-6 mode"
1da177e4	109	depends on BLK_DEV_MD
9bc89cd8 DW	110	select ASYNC_MEMCPY
9bc89cd8 DW	111	select ASYNC_XOR
1da177e4 LT	112	---help---
	113	A RAID-5 set of N drives with a capacity of C MB per drive provides
	114	the capacity of C * (N - 1) MB, and protects against a failure
	115	of a single drive. For a given sector (row) number, (N - 1) drives
	116	contain data sectors, and one drive contains the parity protection.
	117	For a RAID-4 set, the parity blocks are present on a single drive,
	118	while a RAID-5 set distributes the parity across the drives in one
	119	of the available parity distribution methods.
	120
16a53ecc N	121	A RAID-6 set of N drives with a capacity of C MB per drive
	122	provides the capacity of C * (N - 2) MB, and protects
	123	against a failure of any two drives. For a given sector
	124	(row) number, (N - 2) drives contain data sectors, and two
	125	drives contains two independent redundancy syndromes. Like
	126	RAID-5, RAID-6 distributes the syndromes across the drives
	127	in one of the available parity distribution methods.
	128
1da177e4 LT	129	Information about Software RAID on Linux is contained in the
	130	Software-RAID mini-HOWTO, available from
	131	<http://www.tldp.org/docs.html#howto>. There you will also
	132	learn where to get the supporting user space utilities raidtools.
	133
16a53ecc	134	If you want to use such a RAID-4/RAID-5/RAID-6 set, say Y. To
1da177e4	135	compile this code as a module, choose M here: the module
16a53ecc	136	will be called raid456.
1da177e4 LT	137
	138	If unsure, say Y.
	139
29269553	140	config MD_RAID5_RESHAPE
14f50b49 N	141	bool "Support adding drives to a raid-5 array"
	142	depends on MD_RAID456
	143	default y
29269553 N	144	---help---
	145	A RAID-5 set can be expanded by adding extra drives. This
	146	requires "restriping" the array which means (almost) every
	147	block must be written to a different place.
	148
	149	This option allows such restriping to be done while the array
14f50b49	150	is online.
29269553	151
4d2554d0	152	You will need mdadm version 2.4.1 or later to use this
6f91fe88 N	153	feature safely. During the early stage of reshape there is
	154	a critical section where live data is being over-written. A
	155	crash during this time needs extra care for recovery. The
	156	newer mdadm takes a copy of the data in the critical section
	157	and will restore it, if necessary, after a crash.
29269553 N	158
	159	The mdadm usage is e.g.
	160	mdadm --grow /dev/md1 --raid-disks=6
	161	to grow '/dev/md1' to having 6 disks.
	162
	163	Note: The array can only be expanded, not contracted.
	164	There should be enough spares already present to make the new
	165	array workable.
	166
14f50b49 N	167	If unsure, say Y.
14f50b49 N	168
1da177e4 LT	169	config MD_MULTIPATH
	170	tristate "Multipath I/O support"
	171	depends on BLK_DEV_MD
	172	help
	173	Multipath-IO is the ability of certain devices to address the same
	174	physical disk over multiple 'IO paths'. The code ensures that such
	175	paths can be defined and handled at runtime, and ensures that a
	176	transparent failover to the backup path(s) happens if a IO errors
	177	arrives on the primary path.
	178
	179	If unsure, say N.
	180
	181	config MD_FAULTY
	182	tristate "Faulty test module for MD"
	183	depends on BLK_DEV_MD
	184	help
	185	The "faulty" module allows for a block device that occasionally returns
	186	read or write errors. It is useful for testing.
	187
	188	In unsure, say N.
	189
	190	config BLK_DEV_DM
	191	tristate "Device mapper support"
1da177e4 LT	192	---help---
	193	Device-mapper is a low level volume manager. It works by allowing
	194	people to specify mappings for ranges of logical sectors. Various
	195	mapping types are available, in addition people may write their own
	196	modules containing custom mappings if they wish.
	197
	198	Higher level volume managers such as LVM2 use this driver.
	199
	200	To compile this as a module, choose M here: the module will be
	201	called dm-mod.
	202
	203	If unsure, say N.
	204
cc109201 BR	205	config DM_DEBUG
	206	boolean "Device mapper debugging support"
	207	depends on BLK_DEV_DM && EXPERIMENTAL
	208	---help---
	209	Enable this for messages that may help debug device-mapper problems.
	210
	211	If unsure, say N.
	212
1da177e4 LT	213	config DM_CRYPT
	214	tristate "Crypt target support"
	215	depends on BLK_DEV_DM && EXPERIMENTAL
	216	select CRYPTO
3263263f	217	select CRYPTO_CBC
1da177e4 LT	218	---help---
	219	This device-mapper target allows you to create a device that
	220	transparently encrypts the data on it. You'll need to activate
	221	the ciphers you're going to use in the cryptoapi configuration.
	222
	223	Information on how to use dm-crypt can be found on
	224
	225	<http://www.saout.de/misc/dm-crypt/>
	226
	227	To compile this code as a module, choose M here: the module will
	228	be called dm-crypt.
	229
	230	If unsure, say N.
	231
	232	config DM_SNAPSHOT
	233	tristate "Snapshot target (EXPERIMENTAL)"
	234	depends on BLK_DEV_DM && EXPERIMENTAL
	235	---help---
4d2554d0	236	Allow volume managers to take writable snapshots of a device.
1da177e4 LT	237
	238	config DM_MIRROR
	239	tristate "Mirror target (EXPERIMENTAL)"
	240	depends on BLK_DEV_DM && EXPERIMENTAL
	241	---help---
	242	Allow volume managers to mirror logical volumes, also
	243	needed for live data migration tools such as 'pvmove'.
	244
	245	config DM_ZERO
	246	tristate "Zero target (EXPERIMENTAL)"
	247	depends on BLK_DEV_DM && EXPERIMENTAL
	248	---help---
	249	A target that discards writes, and returns all zeroes for
	250	reads. Useful in some recovery situations.
	251
	252	config DM_MULTIPATH
	253	tristate "Multipath target (EXPERIMENTAL)"
	254	depends on BLK_DEV_DM && EXPERIMENTAL
	255	---help---
	256	Allow volume managers to support multipath hardware.
	257
	258	config DM_MULTIPATH_EMC
	259	tristate "EMC CX/AX multipath support (EXPERIMENTAL)"
	260	depends on DM_MULTIPATH && BLK_DEV_DM && EXPERIMENTAL
	261	---help---
	262	Multipath support for EMC CX/AX series hardware.
	263
dd172d72 CS	264	config DM_MULTIPATH_RDAC
dd172d72 CS	265	tristate "LSI/Engenio RDAC multipath support (EXPERIMENTAL)"
6e106b0d	266	depends on DM_MULTIPATH && BLK_DEV_DM && SCSI && EXPERIMENTAL
dd172d72 CS	267	---help---
	268	Multipath support for LSI/Engenio RDAC.
	269
16ebbf35 DW	270	config DM_MULTIPATH_HP
	271	tristate "HP MSA multipath support (EXPERIMENTAL)"
	272	depends on DM_MULTIPATH && BLK_DEV_DM && EXPERIMENTAL
	273	---help---
	274	Multipath support for HP MSA (Active/Passive) series hardware.
	275
26b9f228 HM	276	config DM_DELAY
	277	tristate "I/O delaying target (EXPERIMENTAL)"
	278	depends on BLK_DEV_DM && EXPERIMENTAL
	279	---help---
	280	A target that delays reads and/or writes and can send
	281	them to different devices. Useful for testing.
	282
	283	If unsure, say N.
	284
afd44034	285	endif # MD