ide: set hwif->expiry prior to calling [__]ide_set_handler()

[linux-2.6-block.git] / drivers / ide / tc86c001.c

/*
 * Copyright (C) 2002 Toshiba Corporation
 * Copyright (C) 2005-2006 MontaVista Software, Inc. <source@mvista.com>
 *
 * This file is licensed under the terms of the GNU General Public
 * License version 2.  This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */

#include <linux/types.h>
#include <linux/pci.h>
#include <linux/ide.h>

#define DRV_NAME "tc86c001"

static void tc86c001_set_mode(ide_drive_t *drive, const u8 speed)
{
	ide_hwif_t *hwif	= drive->hwif;
	unsigned long scr_port	= hwif->config_data + (drive->dn ? 0x02 : 0x00);
	u16 mode, scr		= inw(scr_port);

	switch (speed) {
	case XFER_UDMA_4:	mode = 0x00c0; break;
	case XFER_UDMA_3:	mode = 0x00b0; break;
	case XFER_UDMA_2:	mode = 0x00a0; break;
	case XFER_UDMA_1:	mode = 0x0090; break;
	case XFER_UDMA_0:	mode = 0x0080; break;
	case XFER_MW_DMA_2:	mode = 0x0070; break;
	case XFER_MW_DMA_1:	mode = 0x0060; break;
	case XFER_MW_DMA_0:	mode = 0x0050; break;
	case XFER_PIO_4:	mode = 0x0400; break;
	case XFER_PIO_3:	mode = 0x0300; break;
	case XFER_PIO_2:	mode = 0x0200; break;
	case XFER_PIO_1:	mode = 0x0100; break;
	case XFER_PIO_0:
	default:		mode = 0x0000; break;
	}

	scr &= (speed < XFER_MW_DMA_0) ? 0xf8ff : 0xff0f;
	scr |= mode;
	outw(scr, scr_port);
}

static void tc86c001_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
	tc86c001_set_mode(drive, XFER_PIO_0 + pio);
}

/*
 * HACKITY HACK
 *
 * This is a workaround for the limitation 5 of the TC86C001 IDE controller:
 * if a DMA transfer terminates prematurely, the controller leaves the device's
 * interrupt request (INTRQ) pending and does not generate a PCI interrupt (or
 * set the interrupt bit in the DMA status register), thus no PCI interrupt
 * will occur until a DMA transfer has been successfully completed.
 *
 * We work around this by initiating dummy, zero-length DMA transfer on
 * a DMA timeout expiration. I found no better way to do this with the current
 * IDE core than to temporarily replace a higher level driver's timer expiry
 * handler with our own backing up to that handler in case our recovery fails.
 */
static int tc86c001_timer_expiry(ide_drive_t *drive)
{
	ide_hwif_t *hwif	= drive->hwif;
	ide_expiry_t *expiry	= ide_get_hwifdata(hwif);
	u8 dma_stat		= inb(hwif->dma_base + ATA_DMA_STATUS);

	/* Restore a higher level driver's expiry handler first. */
	hwif->expiry = expiry;

	if ((dma_stat & 5) == 1) {	/* DMA active and no interrupt */
		unsigned long sc_base	= hwif->config_data;
		unsigned long twcr_port	= sc_base + (drive->dn ? 0x06 : 0x04);
		u8 dma_cmd		= inb(hwif->dma_base + ATA_DMA_CMD);

		printk(KERN_WARNING "%s: DMA interrupt possibly stuck, "
		       "attempting recovery...\n", drive->name);

		/* Stop DMA */
		outb(dma_cmd & ~0x01, hwif->dma_base + ATA_DMA_CMD);

		/* Setup the dummy DMA transfer */
		outw(0, sc_base + 0x0a);	/* Sector Count */
		outw(0, twcr_port);	/* Transfer Word Count 1 or 2 */

		/* Start the dummy DMA transfer */

		/* clear R_OR_WCTR for write */
		outb(0x00, hwif->dma_base + ATA_DMA_CMD);
		/* set START_STOPBM */
		outb(0x01, hwif->dma_base + ATA_DMA_CMD);

		/*
		 * If an interrupt was pending, it should come thru shortly.
		 * If not, a higher level driver's expiry handler should
		 * eventually cause some kind of recovery from the DMA stall.
		 */
		return WAIT_MIN_SLEEP;
	}

	/* Chain to the restored expiry handler if DMA wasn't active. */
	if (likely(expiry != NULL))
		return expiry(drive);

	/* If there was no handler, "emulate" that for ide_timer_expiry()... */
	return -1;
}

static void tc86c001_dma_start(ide_drive_t *drive)
{
	ide_hwif_t *hwif	= drive->hwif;
	unsigned long sc_base	= hwif->config_data;
	unsigned long twcr_port	= sc_base + (drive->dn ? 0x06 : 0x04);
	unsigned long nsectors	= hwif->rq->nr_sectors;

	/*
	 * We have to manually load the sector count and size into
	 * the appropriate system control registers for DMA to work
	 * with LBA48 and ATAPI devices...
	 */
	outw(nsectors, sc_base + 0x0a);	/* Sector Count */
	outw(SECTOR_SIZE / 2, twcr_port); /* Transfer Word Count 1/2 */

	/* Install our timeout expiry hook, saving the current handler... */
	ide_set_hwifdata(hwif, hwif->expiry);
	hwif->expiry = &tc86c001_timer_expiry;

	ide_dma_start(drive);
}

static u8 tc86c001_cable_detect(ide_hwif_t *hwif)
{
	struct pci_dev *dev = to_pci_dev(hwif->dev);
	unsigned long sc_base = pci_resource_start(dev, 5);
	u16 scr1 = inw(sc_base + 0x00);

	/*
	 * System Control  1 Register bit 13 (PDIAGN):
	 * 0=80-pin cable, 1=40-pin cable
	 */
	return (scr1 & 0x2000) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}

static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
{
	struct pci_dev *dev	= to_pci_dev(hwif->dev);
	unsigned long sc_base	= pci_resource_start(dev, 5);
	u16 scr1		= inw(sc_base + 0x00);

	/* System Control 1 Register bit 15 (Soft Reset) set */
	outw(scr1 |  0x8000, sc_base + 0x00);

	/* System Control 1 Register bit 14 (FIFO Reset) set */
	outw(scr1 |  0x4000, sc_base + 0x00);

	/* System Control 1 Register: reset clear */
	outw(scr1 & ~0xc000, sc_base + 0x00);

	/* Store the system control register base for convenience... */
	hwif->config_data = sc_base;

	if (!hwif->dma_base)
		return;

	/*
	 * Sector Count Control Register bits 0 and 1 set:
	 * software sets Sector Count Register for master and slave device
	 */
	outw(0x0003, sc_base + 0x0c);

	/* Sector Count Register limit */
	hwif->rqsize	 = 0xffff;
}

static const struct ide_port_ops tc86c001_port_ops = {
	.set_pio_mode		= tc86c001_set_pio_mode,
	.set_dma_mode		= tc86c001_set_mode,
	.cable_detect		= tc86c001_cable_detect,
};

static const struct ide_dma_ops tc86c001_dma_ops = {
	.dma_host_set		= ide_dma_host_set,
	.dma_setup		= ide_dma_setup,
	.dma_exec_cmd		= ide_dma_exec_cmd,
	.dma_start		= tc86c001_dma_start,
	.dma_end		= ide_dma_end,
	.dma_test_irq		= ide_dma_test_irq,
	.dma_lost_irq		= ide_dma_lost_irq,
	.dma_timeout		= ide_dma_timeout,
	.dma_sff_read_status	= ide_dma_sff_read_status,
};

static const struct ide_port_info tc86c001_chipset __devinitdata = {
	.name		= DRV_NAME,
	.init_hwif	= init_hwif_tc86c001,
	.port_ops	= &tc86c001_port_ops,
	.dma_ops	= &tc86c001_dma_ops,
	.host_flags	= IDE_HFLAG_SINGLE | IDE_HFLAG_OFF_BOARD,
	.pio_mask	= ATA_PIO4,
	.mwdma_mask	= ATA_MWDMA2,
	.udma_mask	= ATA_UDMA4,
};

static int __devinit tc86c001_init_one(struct pci_dev *dev,
				       const struct pci_device_id *id)
{
	int rc;

	rc = pci_enable_device(dev);
	if (rc)
		goto out;

	rc = pci_request_region(dev, 5, DRV_NAME);
	if (rc) {
		printk(KERN_ERR DRV_NAME ": system control regs already in use");
		goto out_disable;
	}

	rc = ide_pci_init_one(dev, &tc86c001_chipset, NULL);
	if (rc)
		goto out_release;

	goto out;

out_release:
	pci_release_region(dev, 5);
out_disable:
	pci_disable_device(dev);
out:
	return rc;
}

static void __devexit tc86c001_remove(struct pci_dev *dev)
{
	ide_pci_remove(dev);
	pci_release_region(dev, 5);
	pci_disable_device(dev);
}

static const struct pci_device_id tc86c001_pci_tbl[] = {
	{ PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE), 0 },
	{ 0, }
};
MODULE_DEVICE_TABLE(pci, tc86c001_pci_tbl);

static struct pci_driver tc86c001_pci_driver = {
	.name		= "TC86C001",
	.id_table	= tc86c001_pci_tbl,
	.probe		= tc86c001_init_one,
	.remove		= __devexit_p(tc86c001_remove),
};

static int __init tc86c001_ide_init(void)
{
	return ide_pci_register_driver(&tc86c001_pci_driver);
}

static void __exit tc86c001_ide_exit(void)
{
	pci_unregister_driver(&tc86c001_pci_driver);
}

module_init(tc86c001_ide_init);
module_exit(tc86c001_ide_exit);

MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
MODULE_DESCRIPTION("PCI driver module for TC86C001 IDE");
MODULE_LICENSE("GPL");