[linux-2.6-block.git] / drivers / edac / r82600_edac.c

/*
 * Radisys 82600 Embedded chipset Memory Controller kernel module
 * (C) 2005 EADS Astrium
 * This file may be distributed under the terms of the
 * GNU General Public License.
 *
 * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
 * Harbaugh, Dan Hollis <goemon at anime dot net> and others.
 *
 * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
 *
 * Written with reference to 82600 High Integration Dual PCI System
 * Controller Data Book:
 * www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
 * references to this document given in []
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/pci_ids.h>
#include <linux/slab.h>
#include <linux/edac.h>
#include "edac_core.h"

#define R82600_REVISION	" Ver: 2.0.2 " __DATE__
#define EDAC_MOD_STR	"r82600_edac"

#define r82600_printk(level, fmt, arg...) \
	edac_printk(level, "r82600", fmt, ##arg)

#define r82600_mc_printk(mci, level, fmt, arg...) \
	edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)

/* Radisys say "The 82600 integrates a main memory SDRAM controller that
 * supports up to four banks of memory. The four banks can support a mix of
 * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
 * each of which can be any size from 16MB to 512MB. Both registered (control
 * signals buffered) and unbuffered DIMM types are supported. Mixing of
 * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
 * is not allowed. The 82600 SDRAM interface operates at the same frequency as
 * the CPU bus, 66MHz, 100MHz or 133MHz."
 */

#define R82600_NR_CSROWS 4
#define R82600_NR_CHANS  1
#define R82600_NR_DIMMS  4

#define R82600_BRIDGE_ID  0x8200

/* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
#define R82600_DRAMC	0x57	/* Various SDRAM related control bits
				 * all bits are R/W
				 *
				 * 7    SDRAM ISA Hole Enable
				 * 6    Flash Page Mode Enable
				 * 5    ECC Enable: 1=ECC 0=noECC
				 * 4    DRAM DIMM Type: 1=
				 * 3    BIOS Alias Disable
				 * 2    SDRAM BIOS Flash Write Enable
				 * 1:0  SDRAM Refresh Rate: 00=Disabled
				 *          01=7.8usec (256Mbit SDRAMs)
				 *          10=15.6us 11=125usec
				 */

#define R82600_SDRAMC	0x76	/* "SDRAM Control Register"
				 * More SDRAM related control bits
				 * all bits are R/W
				 *
				 * 15:8 Reserved.
				 *
				 * 7:5  Special SDRAM Mode Select
				 *
				 * 4    Force ECC
				 *
				 *        1=Drive ECC bits to 0 during
				 *          write cycles (i.e. ECC test mode)
				 *
				 *        0=Normal ECC functioning
				 *
				 * 3    Enhanced Paging Enable
				 *
				 * 2    CAS# Latency 0=3clks 1=2clks
				 *
				 * 1    RAS# to CAS# Delay 0=3 1=2
				 *
				 * 0    RAS# Precharge     0=3 1=2
				 */

#define R82600_EAP	0x80	/* ECC Error Address Pointer Register
				 *
				 * 31    Disable Hardware Scrubbing (RW)
				 *        0=Scrub on corrected read
				 *        1=Don't scrub on corrected read
				 *
				 * 30:12 Error Address Pointer (RO)
				 *        Upper 19 bits of error address
				 *
				 * 11:4  Syndrome Bits (RO)
				 *
				 * 3     BSERR# on multibit error (RW)
				 *        1=enable 0=disable
				 *
				 * 2     NMI on Single Bit Eror (RW)
				 *        1=NMI triggered by SBE n.b. other
				 *          prerequeists
				 *        0=NMI not triggered
				 *
				 * 1     MBE (R/WC)
				 *        read 1=MBE at EAP (see above)
				 *        read 0=no MBE, or SBE occurred first
				 *        write 1=Clear MBE status (must also
				 *          clear SBE)
				 *        write 0=NOP
				 *
				 * 1     SBE (R/WC)
				 *        read 1=SBE at EAP (see above)
				 *        read 0=no SBE, or MBE occurred first
				 *        write 1=Clear SBE status (must also
				 *          clear MBE)
				 *        write 0=NOP
				 */

#define R82600_DRBA	0x60	/* + 0x60..0x63 SDRAM Row Boundry Address
				 *  Registers
				 *
				 * 7:0  Address lines 30:24 - upper limit of
				 * each row [p57]
				 */

struct r82600_error_info {
	u32 eapr;
};

static unsigned int disable_hardware_scrub;

static struct edac_pci_ctl_info *r82600_pci;

static void r82600_get_error_info(struct mem_ctl_info *mci,
				struct r82600_error_info *info)
{
	struct pci_dev *pdev;

	pdev = to_pci_dev(mci->dev);
	pci_read_config_dword(pdev, R82600_EAP, &info->eapr);

	if (info->eapr & BIT(0))
		/* Clear error to allow next error to be reported [p.62] */
		pci_write_bits32(pdev, R82600_EAP,
				 ((u32) BIT(0) & (u32) BIT(1)),
				 ((u32) BIT(0) & (u32) BIT(1)));

	if (info->eapr & BIT(1))
		/* Clear error to allow next error to be reported [p.62] */
		pci_write_bits32(pdev, R82600_EAP,
				 ((u32) BIT(0) & (u32) BIT(1)),
				 ((u32) BIT(0) & (u32) BIT(1)));
}

static int r82600_process_error_info(struct mem_ctl_info *mci,
				struct r82600_error_info *info,
				int handle_errors)
{
	int error_found;
	u32 eapaddr, page;
	u32 syndrome;

	error_found = 0;

	/* bits 30:12 store the upper 19 bits of the 32 bit error address */
	eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
	/* Syndrome in bits 11:4 [p.62]       */
	syndrome = (info->eapr >> 4) & 0xFF;

	/* the R82600 reports at less than page *
	 * granularity (upper 19 bits only)     */
	page = eapaddr >> PAGE_SHIFT;

	if (info->eapr & BIT(0)) {	/* CE? */
		error_found = 1;

		if (handle_errors)
			edac_mc_handle_ce(mci, page, 0,	/* not avail */
					syndrome,
					edac_mc_find_csrow_by_page(mci, page),
					0, mci->ctl_name);
	}

	if (info->eapr & BIT(1)) {	/* UE? */
		error_found = 1;

		if (handle_errors)
			/* 82600 doesn't give enough info */
			edac_mc_handle_ue(mci, page, 0,
					edac_mc_find_csrow_by_page(mci, page),
					mci->ctl_name);
	}

	return error_found;
}

static void r82600_check(struct mem_ctl_info *mci)
{
	struct r82600_error_info info;

	debugf1("MC%d: %s()\n", mci->mc_idx, __func__);
	r82600_get_error_info(mci, &info);
	r82600_process_error_info(mci, &info, 1);
}

static inline int ecc_enabled(u8 dramcr)
{
	return dramcr & BIT(5);
}

static void r82600_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev,
			u8 dramcr)
{
	struct csrow_info *csrow;
	int index;
	u8 drbar;		/* SDRAM Row Boundry Address Register */
	u32 row_high_limit, row_high_limit_last;
	u32 reg_sdram, ecc_on, row_base;

	ecc_on = ecc_enabled(dramcr);
	reg_sdram = dramcr & BIT(4);
	row_high_limit_last = 0;

	for (index = 0; index < mci->nr_csrows; index++) {
		csrow = &mci->csrows[index];

		/* find the DRAM Chip Select Base address and mask */
		pci_read_config_byte(pdev, R82600_DRBA + index, &drbar);

		debugf1("%s() Row=%d DRBA = %#0x\n", __func__, index, drbar);

		row_high_limit = ((u32) drbar << 24);
/*		row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */

		debugf1("%s() Row=%d, Boundry Address=%#0x, Last = %#0x\n",
			__func__, index, row_high_limit, row_high_limit_last);

		/* Empty row [p.57] */
		if (row_high_limit == row_high_limit_last)
			continue;

		row_base = row_high_limit_last;

		csrow->first_page = row_base >> PAGE_SHIFT;
		csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;
		csrow->nr_pages = csrow->last_page - csrow->first_page + 1;
		/* Error address is top 19 bits - so granularity is      *
		 * 14 bits                                               */
		csrow->grain = 1 << 14;
		csrow->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
		/* FIXME - check that this is unknowable with this chipset */
		csrow->dtype = DEV_UNKNOWN;

		/* Mode is global on 82600 */
		csrow->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
		row_high_limit_last = row_high_limit;
	}
}

static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
{
	struct mem_ctl_info *mci;
	u8 dramcr;
	u32 eapr;
	u32 scrub_disabled;
	u32 sdram_refresh_rate;
	struct r82600_error_info discard;

	debugf0("%s()\n", __func__);
	pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
	pci_read_config_dword(pdev, R82600_EAP, &eapr);
	scrub_disabled = eapr & BIT(31);
	sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
	debugf2("%s(): sdram refresh rate = %#0x\n", __func__,
		sdram_refresh_rate);
	debugf2("%s(): DRAMC register = %#0x\n", __func__, dramcr);
	mci = edac_mc_alloc(0, R82600_NR_CSROWS, R82600_NR_CHANS, 0);

	if (mci == NULL)
		return -ENOMEM;

	debugf0("%s(): mci = %p\n", __func__, mci);
	mci->dev = &pdev->dev;
	mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
	mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
	/* FIXME try to work out if the chip leads have been used for COM2
	 * instead on this board? [MA6?] MAYBE:
	 */

	/* On the R82600, the pins for memory bits 72:65 - i.e. the   *
	 * EC bits are shared with the pins for COM2 (!), so if COM2  *
	 * is enabled, we assume COM2 is wired up, and thus no EDAC   *
	 * is possible.                                               */
	mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;

	if (ecc_enabled(dramcr)) {
		if (scrub_disabled)
			debugf3("%s(): mci = %p - Scrubbing disabled! EAP: "
				"%#0x\n", __func__, mci, eapr);
	} else
		mci->edac_cap = EDAC_FLAG_NONE;

	mci->mod_name = EDAC_MOD_STR;
	mci->mod_ver = R82600_REVISION;
	mci->ctl_name = "R82600";
	mci->dev_name = pci_name(pdev);
	mci->edac_check = r82600_check;
	mci->ctl_page_to_phys = NULL;
	r82600_init_csrows(mci, pdev, dramcr);
	r82600_get_error_info(mci, &discard);	/* clear counters */

	/* Here we assume that we will never see multiple instances of this
	 * type of memory controller.  The ID is therefore hardcoded to 0.
	 */
	if (edac_mc_add_mc(mci)) {
		debugf3("%s(): failed edac_mc_add_mc()\n", __func__);
		goto fail;
	}

	/* get this far and it's successful */

	if (disable_hardware_scrub) {
		debugf3("%s(): Disabling Hardware Scrub (scrub on error)\n",
			__func__);
		pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31));
	}

	/* allocating generic PCI control info */
	r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
	if (!r82600_pci) {
		printk(KERN_WARNING
			"%s(): Unable to create PCI control\n",
			__func__);
		printk(KERN_WARNING
			"%s(): PCI error report via EDAC not setup\n",
			__func__);
	}

	debugf3("%s(): success\n", __func__);
	return 0;

fail:
	edac_mc_free(mci);
	return -ENODEV;
}

/* returns count (>= 0), or negative on error */
static int __devinit r82600_init_one(struct pci_dev *pdev,
				const struct pci_device_id *ent)
{
	debugf0("%s()\n", __func__);

	/* don't need to call pci_device_enable() */
	return r82600_probe1(pdev, ent->driver_data);
}

static void __devexit r82600_remove_one(struct pci_dev *pdev)
{
	struct mem_ctl_info *mci;

	debugf0("%s()\n", __func__);

	if (r82600_pci)
		edac_pci_release_generic_ctl(r82600_pci);

	if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
		return;

	edac_mc_free(mci);
}

static const struct pci_device_id r82600_pci_tbl[] __devinitdata = {
	{
	 PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)
	 },
	{
	 0,
	 }			/* 0 terminated list. */
};

MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);

static struct pci_driver r82600_driver = {
	.name = EDAC_MOD_STR,
	.probe = r82600_init_one,
	.remove = __devexit_p(r82600_remove_one),
	.id_table = r82600_pci_tbl,
};

static int __init r82600_init(void)
{
       /* Ensure that the OPSTATE is set correctly for POLL or NMI */
       opstate_init();

	return pci_register_driver(&r82600_driver);
}

static void __exit r82600_exit(void)
{
	pci_unregister_driver(&r82600_driver);
}

module_init(r82600_init);
module_exit(r82600_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
		"on behalf of EADS Astrium");
MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");

module_param(disable_hardware_scrub, bool, 0644);
MODULE_PARM_DESC(disable_hardware_scrub,
		 "If set, disable the chipset's automatic scrub for CEs");

module_param(edac_op_state, int, 0444);
MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");
Commit	Line	Data
2f768af7 AC	1	/*
	2	* Radisys 82600 Embedded chipset Memory Controller kernel module
	3	* (C) 2005 EADS Astrium
	4	* This file may be distributed under the terms of the
	5	* GNU General Public License.
	6	*
	7	* Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
	8	* Harbaugh, Dan Hollis <goemon at anime dot net> and others.
	9	*
	10	* $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
	11	*
	12	* Written with reference to 82600 High Integration Dual PCI System
	13	* Controller Data Book:
c4192705	14	* www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
2f768af7 AC	15	* references to this document given in []
	16	*/
	17
2f768af7 AC	18	#include <linux/module.h>
2f768af7 AC	19	#include <linux/init.h>
2f768af7 AC	20	#include <linux/pci.h>
2f768af7 AC	21	#include <linux/pci_ids.h>
2f768af7	22	#include <linux/slab.h>
c3c52bce	23	#include <linux/edac.h>
20bcb7a8	24	#include "edac_core.h"
2f768af7	25
20bcb7a8	26	#define R82600_REVISION " Ver: 2.0.2 " __DATE__
929a40ec	27	#define EDAC_MOD_STR "r82600_edac"
37f04581	28
537fba28	29	#define r82600_printk(level, fmt, arg...) \
e7ecd891	30	edac_printk(level, "r82600", fmt, ##arg)
537fba28 DP	31
537fba28 DP	32	#define r82600_mc_printk(mci, level, fmt, arg...) \
e7ecd891	33	edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)
537fba28	34
2f768af7 AC	35	/* Radisys say "The 82600 integrates a main memory SDRAM controller that
	36	* supports up to four banks of memory. The four banks can support a mix of
	37	* sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
	38	* each of which can be any size from 16MB to 512MB. Both registered (control
	39	* signals buffered) and unbuffered DIMM types are supported. Mixing of
	40	* registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
	41	* is not allowed. The 82600 SDRAM interface operates at the same frequency as
	42	* the CPU bus, 66MHz, 100MHz or 133MHz."
	43	*/
	44
	45	#define R82600_NR_CSROWS 4
	46	#define R82600_NR_CHANS 1
	47	#define R82600_NR_DIMMS 4
	48
	49	#define R82600_BRIDGE_ID 0x8200
	50
	51	/* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
	52	#define R82600_DRAMC 0x57 /* Various SDRAM related control bits
	53	* all bits are R/W
	54	*
	55	* 7 SDRAM ISA Hole Enable
	56	* 6 Flash Page Mode Enable
	57	* 5 ECC Enable: 1=ECC 0=noECC
	58	* 4 DRAM DIMM Type: 1=
	59	* 3 BIOS Alias Disable
	60	* 2 SDRAM BIOS Flash Write Enable
	61	* 1:0 SDRAM Refresh Rate: 00=Disabled
	62	* 01=7.8usec (256Mbit SDRAMs)
	63	* 10=15.6us 11=125usec
	64	*/
	65
	66	#define R82600_SDRAMC 0x76 /* "SDRAM Control Register"
	67	* More SDRAM related control bits
	68	* all bits are R/W
	69	*
	70	* 15:8 Reserved.
	71	*
	72	* 7:5 Special SDRAM Mode Select
	73	*
	74	* 4 Force ECC
	75	*
	76	* 1=Drive ECC bits to 0 during
	77	* write cycles (i.e. ECC test mode)
	78	*
	79	* 0=Normal ECC functioning
	80	*
	81	* 3 Enhanced Paging Enable
	82	*
	83	* 2 CAS# Latency 0=3clks 1=2clks
	84	*
	85	* 1 RAS# to CAS# Delay 0=3 1=2
	86	*
	87	* 0 RAS# Precharge 0=3 1=2
	88	*/
	89
	90	#define R82600_EAP 0x80 /* ECC Error Address Pointer Register
	91	*
	92	* 31 Disable Hardware Scrubbing (RW)
	93	* 0=Scrub on corrected read
	94	* 1=Don't scrub on corrected read
	95	*
	96	* 30:12 Error Address Pointer (RO)
	97	* Upper 19 bits of error address
	98	*
99	* 11:4 Syndrome Bits (RO)
100	*
101	* 3 BSERR# on multibit error (RW)
102	* 1=enable 0=disable
103	*
104	* 2 NMI on Single Bit Eror (RW)
105	* 1=NMI triggered by SBE n.b. other
106	* prerequeists
107	* 0=NMI not triggered
108	*
109	* 1 MBE (R/WC)
110	* read 1=MBE at EAP (see above)
111	* read 0=no MBE, or SBE occurred first
112	* write 1=Clear MBE status (must also
113	* clear SBE)
114	* write 0=NOP
115	*
116	* 1 SBE (R/WC)
117	* read 1=SBE at EAP (see above)
118	* read 0=no SBE, or MBE occurred first
119	* write 1=Clear SBE status (must also
120	* clear MBE)
121	* write 0=NOP
122	*/
123
124	#define R82600_DRBA 0x60 /* + 0x60..0x63 SDRAM Row Boundry Address
125	* Registers
126	*
127	* 7:0 Address lines 30:24 - upper limit of
128	* each row [p57]
129	*/
130
131	struct r82600_error_info {
132	u32 eapr;
133	};
134
f044091c	135	static unsigned int disable_hardware_scrub;
2f768af7	136
456a2f95 DJ	137	static struct edac_pci_ctl_info *r82600_pci;
456a2f95 DJ	138
cddbfcac	139	static void r82600_get_error_info(struct mem_ctl_info *mci,
052dfb45	140	struct r82600_error_info *info)
2f768af7	141	{
37f04581 DT	142	struct pci_dev *pdev;
	143
	144	pdev = to_pci_dev(mci->dev);
	145	pci_read_config_dword(pdev, R82600_EAP, &info->eapr);
2f768af7 AC	146
	147	if (info->eapr & BIT(0))
	148	/* Clear error to allow next error to be reported [p.62] */
37f04581	149	pci_write_bits32(pdev, R82600_EAP,
cddbfcac DT	150	((u32) BIT(0) & (u32) BIT(1)),
cddbfcac DT	151	((u32) BIT(0) & (u32) BIT(1)));
2f768af7 AC	152
	153	if (info->eapr & BIT(1))
	154	/* Clear error to allow next error to be reported [p.62] */
37f04581	155	pci_write_bits32(pdev, R82600_EAP,
cddbfcac DT	156	((u32) BIT(0) & (u32) BIT(1)),
cddbfcac DT	157	((u32) BIT(0) & (u32) BIT(1)));
2f768af7 AC	158	}
2f768af7 AC	159
cddbfcac	160	static int r82600_process_error_info(struct mem_ctl_info *mci,
052dfb45 DT	161	struct r82600_error_info *info,
052dfb45 DT	162	int handle_errors)
2f768af7 AC	163	{
	164	int error_found;
	165	u32 eapaddr, page;
	166	u32 syndrome;
	167
	168	error_found = 0;
	169
	170	/* bits 30:12 store the upper 19 bits of the 32 bit error address */
	171	eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
	172	/* Syndrome in bits 11:4 [p.62] */
	173	syndrome = (info->eapr >> 4) & 0xFF;
	174
	175	/* the R82600 reports at less than page *
	176	* granularity (upper 19 bits only) */
	177	page = eapaddr >> PAGE_SHIFT;
	178
cddbfcac	179	if (info->eapr & BIT(0)) { /* CE? */
2f768af7 AC	180	error_found = 1;
	181
	182	if (handle_errors)
cddbfcac	183	edac_mc_handle_ce(mci, page, 0, /* not avail */
052dfb45 DT	184	syndrome,
	185	edac_mc_find_csrow_by_page(mci, page),
	186	0, mci->ctl_name);
2f768af7 AC	187	}
2f768af7 AC	188
cddbfcac	189	if (info->eapr & BIT(1)) { /* UE? */
2f768af7 AC	190	error_found = 1;
	191
	192	if (handle_errors)
	193	/* 82600 doesn't give enough info */
	194	edac_mc_handle_ue(mci, page, 0,
052dfb45 DT	195	edac_mc_find_csrow_by_page(mci, page),
052dfb45 DT	196	mci->ctl_name);
2f768af7 AC	197	}
	198
	199	return error_found;
	200	}
	201
	202	static void r82600_check(struct mem_ctl_info *mci)
	203	{
	204	struct r82600_error_info info;
	205
537fba28	206	debugf1("MC%d: %s()\n", mci->mc_idx, __func__);
2f768af7 AC	207	r82600_get_error_info(mci, &info);
	208	r82600_process_error_info(mci, &info, 1);
	209	}
	210
13189525	211	static inline int ecc_enabled(u8 dramcr)
2f768af7	212	{
13189525 DT	213	return dramcr & BIT(5);
	214	}
	215
	216	static void r82600_init_csrows(struct mem_ctl_info mci, struct pci_dev pdev,
052dfb45	217	u8 dramcr)
13189525 DT	218	{
13189525 DT	219	struct csrow_info *csrow;
2f768af7	220	int index;
cddbfcac	221	u8 drbar; /* SDRAM Row Boundry Address Register */
13189525 DT	222	u32 row_high_limit, row_high_limit_last;
	223	u32 reg_sdram, ecc_on, row_base;
	224
	225	ecc_on = ecc_enabled(dramcr);
	226	reg_sdram = dramcr & BIT(4);
	227	row_high_limit_last = 0;
	228
	229	for (index = 0; index < mci->nr_csrows; index++) {
	230	csrow = &mci->csrows[index];
	231
	232	/* find the DRAM Chip Select Base address and mask */
	233	pci_read_config_byte(pdev, R82600_DRBA + index, &drbar);
	234
	235	debugf1("%s() Row=%d DRBA = %#0x\n", __func__, index, drbar);
	236
	237	row_high_limit = ((u32) drbar << 24);
	238	/* row_high_limit = ((u32)drbar << 24) \| 0xffffffUL; */
	239
	240	debugf1("%s() Row=%d, Boundry Address=%#0x, Last = %#0x\n",
	241	__func__, index, row_high_limit, row_high_limit_last);
	242
	243	/* Empty row [p.57] */
	244	if (row_high_limit == row_high_limit_last)
	245	continue;
	246
	247	row_base = row_high_limit_last;
	248
	249	csrow->first_page = row_base >> PAGE_SHIFT;
	250	csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;
	251	csrow->nr_pages = csrow->last_page - csrow->first_page + 1;
	252	/* Error address is top 19 bits - so granularity is *
	253	* 14 bits */
	254	csrow->grain = 1 << 14;
	255	csrow->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
	256	/* FIXME - check that this is unknowable with this chipset */
	257	csrow->dtype = DEV_UNKNOWN;
	258
	259	/* Mode is global on 82600 */
	260	csrow->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
	261	row_high_limit_last = row_high_limit;
	262	}
	263	}
	264
	265	static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
	266	{
	267	struct mem_ctl_info *mci;
2f768af7	268	u8 dramcr;
2f768af7 AC	269	u32 eapr;
	270	u32 scrub_disabled;
	271	u32 sdram_refresh_rate;
749ede57	272	struct r82600_error_info discard;
2f768af7	273
537fba28	274	debugf0("%s()\n", __func__);
2f768af7 AC	275	pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
2f768af7 AC	276	pci_read_config_dword(pdev, R82600_EAP, &eapr);
2f768af7 AC	277	scrub_disabled = eapr & BIT(31);
2f768af7 AC	278	sdram_refresh_rate = dramcr & (BIT(0) \| BIT(1));
537fba28 DP	279	debugf2("%s(): sdram refresh rate = %#0x\n", __func__,
537fba28 DP	280	sdram_refresh_rate);
537fba28	281	debugf2("%s(): DRAMC register = %#0x\n", __func__, dramcr);
b8f6f975	282	mci = edac_mc_alloc(0, R82600_NR_CSROWS, R82600_NR_CHANS, 0);
2f768af7	283
13189525 DT	284	if (mci == NULL)
13189525 DT	285	return -ENOMEM;
2f768af7	286
537fba28	287	debugf0("%s(): mci = %p\n", __func__, mci);
37f04581	288	mci->dev = &pdev->dev;
2f768af7	289	mci->mtype_cap = MEM_FLAG_RDDR \| MEM_FLAG_DDR;
2f768af7	290	mci->edac_ctl_cap = EDAC_FLAG_NONE \| EDAC_FLAG_EC \| EDAC_FLAG_SECDED;
e7ecd891 DP	291	/* FIXME try to work out if the chip leads have been used for COM2
	292	* instead on this board? [MA6?] MAYBE:
	293	*/
2f768af7 AC	294
	295	/* On the R82600, the pins for memory bits 72:65 - i.e. the *
	296	* EC bits are shared with the pins for COM2 (!), so if COM2 *
	297	* is enabled, we assume COM2 is wired up, and thus no EDAC *
	298	* is possible. */
	299	mci->edac_cap = EDAC_FLAG_NONE \| EDAC_FLAG_EC \| EDAC_FLAG_SECDED;
e7ecd891	300
13189525	301	if (ecc_enabled(dramcr)) {
2f768af7	302	if (scrub_disabled)
537fba28 DP	303	debugf3("%s(): mci = %p - Scrubbing disabled! EAP: "
537fba28 DP	304	"%#0x\n", __func__, mci, eapr);
2f768af7 AC	305	} else
	306	mci->edac_cap = EDAC_FLAG_NONE;
	307
680cbbbb	308	mci->mod_name = EDAC_MOD_STR;
37f04581	309	mci->mod_ver = R82600_REVISION;
2f768af7	310	mci->ctl_name = "R82600";
c4192705	311	mci->dev_name = pci_name(pdev);
2f768af7 AC	312	mci->edac_check = r82600_check;
2f768af7 AC	313	mci->ctl_page_to_phys = NULL;
13189525	314	r82600_init_csrows(mci, pdev, dramcr);
cddbfcac	315	r82600_get_error_info(mci, &discard); /* clear counters */
2f768af7	316
2d7bbb91 DT	317	/* Here we assume that we will never see multiple instances of this
	318	* type of memory controller. The ID is therefore hardcoded to 0.
	319	*/
b8f6f975	320	if (edac_mc_add_mc(mci)) {
537fba28	321	debugf3("%s(): failed edac_mc_add_mc()\n", __func__);
2f768af7 AC	322	goto fail;
	323	}
	324
	325	/* get this far and it's successful */
	326
2f768af7	327	if (disable_hardware_scrub) {
537fba28 DP	328	debugf3("%s(): Disabling Hardware Scrub (scrub on error)\n",
537fba28 DP	329	__func__);
37f04581	330	pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31));
2f768af7 AC	331	}
2f768af7 AC	332
456a2f95 DJ	333	/* allocating generic PCI control info */
	334	r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
	335	if (!r82600_pci) {
	336	printk(KERN_WARNING
	337	"%s(): Unable to create PCI control\n",
	338	__func__);
	339	printk(KERN_WARNING
	340	"%s(): PCI error report via EDAC not setup\n",
	341	__func__);
	342	}
	343
537fba28	344	debugf3("%s(): success\n", __func__);
2f768af7 AC	345	return 0;
2f768af7 AC	346
052dfb45	347	fail:
13189525 DT	348	edac_mc_free(mci);
13189525 DT	349	return -ENODEV;
2f768af7 AC	350	}
	351
	352	/* returns count (>= 0), or negative on error */
	353	static int __devinit r82600_init_one(struct pci_dev *pdev,
052dfb45	354	const struct pci_device_id *ent)
2f768af7	355	{
537fba28	356	debugf0("%s()\n", __func__);
2f768af7 AC	357
	358	/* don't need to call pci_device_enable() */
	359	return r82600_probe1(pdev, ent->driver_data);
	360	}
	361
2f768af7 AC	362	static void __devexit r82600_remove_one(struct pci_dev *pdev)
	363	{
	364	struct mem_ctl_info *mci;
	365
537fba28	366	debugf0("%s()\n", __func__);
2f768af7	367
456a2f95 DJ	368	if (r82600_pci)
	369	edac_pci_release_generic_ctl(r82600_pci);
	370
37f04581	371	if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
18dbc337 DP	372	return;
	373
	374	edac_mc_free(mci);
2f768af7 AC	375	}
2f768af7 AC	376
2f768af7	377	static const struct pci_device_id r82600_pci_tbl[] __devinitdata = {
e7ecd891	378	{
cddbfcac DT	379	PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)
cddbfcac DT	380	},
e7ecd891	381	{
cddbfcac DT	382	0,
cddbfcac DT	383	} /* 0 terminated list. */
2f768af7 AC	384	};
	385
	386	MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);
	387
2f768af7	388	static struct pci_driver r82600_driver = {
680cbbbb	389	.name = EDAC_MOD_STR,
2f768af7 AC	390	.probe = r82600_init_one,
	391	.remove = __devexit_p(r82600_remove_one),
	392	.id_table = r82600_pci_tbl,
	393	};
	394
da9bb1d2	395	static int __init r82600_init(void)
2f768af7	396	{
c3c52bce HM	397	/* Ensure that the OPSTATE is set correctly for POLL or NMI */
	398	opstate_init();
	399
2f768af7 AC	400	return pci_register_driver(&r82600_driver);
	401	}
	402
2f768af7 AC	403	static void __exit r82600_exit(void)
	404	{
	405	pci_unregister_driver(&r82600_driver);
	406	}
	407
2f768af7 AC	408	module_init(r82600_init);
	409	module_exit(r82600_exit);
	410
2f768af7 AC	411	MODULE_LICENSE("GPL");
2f768af7 AC	412	MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
052dfb45	413	"on behalf of EADS Astrium");
2f768af7 AC	414	MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");
	415
	416	module_param(disable_hardware_scrub, bool, 0644);
	417	MODULE_PARM_DESC(disable_hardware_scrub,
	418	"If set, disable the chipset's automatic scrub for CEs");
c3c52bce HM	419
	420	module_param(edac_op_state, int, 0444);
	421	MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");