ARC: kgdb support

[linux-2.6-block.git] / arch / arc / mm / cache_arc700.c

/*
 * ARC700 VIPT Cache Management
 *
 * Copyright (C) 2004, 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com)
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 *  vineetg: May 2011: for Non-aliasing VIPT D-cache following can be NOPs
 *   -flush_cache_dup_mm (fork)
 *   -likewise for flush_cache_mm (exit/execve)
 *   -likewise for flush_cache_range,flush_cache_page (munmap, exit, COW-break)
 *
 * vineetg: Apr 2011
 *  -Now that MMU can support larger pg sz (16K), the determiniation of
 *   aliasing shd not be based on assumption of 8k pg
 *
 * vineetg: Mar 2011
 *  -optimised version of flush_icache_range( ) for making I/D coherent
 *   when vaddr is available (agnostic of num of aliases)
 *
 * vineetg: Mar 2011
 *  -Added documentation about I-cache aliasing on ARC700 and the way it
 *   was handled up until MMU V2.
 *  -Spotted a three year old bug when killing the 4 aliases, which needs
 *   bottom 2 bits, so we need to do paddr | {0x00, 0x01, 0x02, 0x03}
 *                        instead of paddr | {0x00, 0x01, 0x10, 0x11}
 *   (Rajesh you owe me one now)
 *
 * vineetg: Dec 2010
 *  -Off-by-one error when computing num_of_lines to flush
 *   This broke signal handling with bionic which uses synthetic sigret stub
 *
 * vineetg: Mar 2010
 *  -GCC can't generate ZOL for core cache flush loops.
 *   Conv them into iterations based as opposed to while (start < end) types
 *
 * Vineetg: July 2009
 *  -In I-cache flush routine we used to chk for aliasing for every line INV.
 *   Instead now we setup routines per cache geometry and invoke them
 *   via function pointers.
 *
 * Vineetg: Jan 2009
 *  -Cache Line flush routines used to flush an extra line beyond end addr
 *   because check was while (end >= start) instead of (end > start)
 *     =Some call sites had to work around by doing -1, -4 etc to end param
 *     =Some callers didnt care. This was spec bad in case of INV routines
 *      which would discard valid data (cause of the horrible ext2 bug
 *      in ARC IDE driver)
 *
 * vineetg: June 11th 2008: Fixed flush_icache_range( )
 *  -Since ARC700 caches are not coherent (I$ doesnt snoop D$) both need
 *   to be flushed, which it was not doing.
 *  -load_module( ) passes vmalloc addr (Kernel Virtual Addr) to the API,
 *   however ARC cache maintenance OPs require PHY addr. Thus need to do
 *   vmalloc_to_phy.
 *  -Also added optimisation there, that for range > PAGE SIZE we flush the
 *   entire cache in one shot rather than line by line. For e.g. a module
 *   with Code sz 600k, old code flushed 600k worth of cache (line-by-line),
 *   while cache is only 16 or 32k.
 */

#include <linux/module.h>
#include <linux/mm.h>
#include <linux/sched.h>
#include <linux/cache.h>
#include <linux/mmu_context.h>
#include <linux/syscalls.h>
#include <linux/uaccess.h>
#include <asm/cacheflush.h>
#include <asm/cachectl.h>
#include <asm/setup.h>


#ifdef CONFIG_ARC_HAS_ICACHE
static void __ic_line_inv_no_alias(unsigned long, int);
static void __ic_line_inv_2_alias(unsigned long, int);
static void __ic_line_inv_4_alias(unsigned long, int);

/* Holds the ptr to flush routine, dependign on size due to aliasing issues */
static void (*___flush_icache_rtn) (unsigned long, int);
#endif

/*
 * Read the Cache Build Confuration Registers, Decode them and save into
 * the cpuinfo structure for later use.
 * No Validation done here, simply read/convert the BCRs
 */
void __init read_decode_cache_bcr(void)
{
	struct bcr_cache ibcr, dbcr;
	struct cpuinfo_arc_cache *p_ic, *p_dc;
	unsigned int cpu = smp_processor_id();

	p_ic = &cpuinfo_arc700[cpu].icache;
	READ_BCR(ARC_REG_IC_BCR, ibcr);

	if (ibcr.config == 0x3)
		p_ic->assoc = 2;
	p_ic->line_len = 8 << ibcr.line_len;
	p_ic->sz = 0x200 << ibcr.sz;
	p_ic->ver = ibcr.ver;

	p_dc = &cpuinfo_arc700[cpu].dcache;
	READ_BCR(ARC_REG_DC_BCR, dbcr);

	if (dbcr.config == 0x2)
		p_dc->assoc = 4;
	p_dc->line_len = 16 << dbcr.line_len;
	p_dc->sz = 0x200 << dbcr.sz;
	p_dc->ver = dbcr.ver;
}

/*
 * 1. Validate the Cache Geomtery (compile time config matches hardware)
 * 2. If I-cache suffers from aliasing, setup work arounds (difft flush rtn)
 *    (aliasing D-cache configurations are not supported YET)
 * 3. Enable the Caches, setup default flush mode for D-Cache
 * 3. Calculate the SHMLBA used by user space
 */
void __init arc_cache_init(void)
{
	unsigned int temp;
#ifdef CONFIG_ARC_CACHE
	unsigned int cpu = smp_processor_id();
#endif
#ifdef CONFIG_ARC_HAS_ICACHE
	struct cpuinfo_arc_cache *ic;
#endif
#ifdef CONFIG_ARC_HAS_DCACHE
	struct cpuinfo_arc_cache *dc;
#endif
	int way_pg_ratio = way_pg_ratio;

#ifdef CONFIG_ARC_HAS_ICACHE
	ic = &cpuinfo_arc700[cpu].icache;

	/*
	 * if Cache way size is <= page size then no aliasing exhibited
	 * otherwise ratio determines num of aliases.
	 * e.g. 32K I$, 2 way set assoc, 8k pg size
	 *       way-sz = 32k/2 = 16k
	 *       way-pg-ratio = 16k/8k = 2, so 2 aliases possible
	 *       (meaning 1 line could be in 2 possible locations).
	 */
	way_pg_ratio = ic->sz / ARC_ICACHE_WAYS / PAGE_SIZE;
	switch (way_pg_ratio) {
	case 0:
	case 1:
		___flush_icache_rtn = __ic_line_inv_no_alias;
		break;
	case 2:
		___flush_icache_rtn = __ic_line_inv_2_alias;
		break;
	case 4:
		___flush_icache_rtn = __ic_line_inv_4_alias;
		break;
	default:
		panic("Unsupported I-Cache Sz\n");
	}
#endif

	/* Enable/disable I-Cache */
	temp = read_aux_reg(ARC_REG_IC_CTRL);

#ifdef CONFIG_ARC_HAS_ICACHE
	temp &= ~IC_CTRL_CACHE_DISABLE;
#else
	temp |= IC_CTRL_CACHE_DISABLE;
#endif

	write_aux_reg(ARC_REG_IC_CTRL, temp);

#ifdef CONFIG_ARC_HAS_DCACHE
	dc = &cpuinfo_arc700[cpu].dcache;

	/* check for D-Cache aliasing */
	if ((dc->sz / ARC_DCACHE_WAYS) > PAGE_SIZE)
		panic("D$ aliasing not handled right now\n");
#endif

	/* Set the default Invalidate Mode to "simpy discard dirty lines"
	 *  as this is more frequent then flush before invalidate
	 * Ofcourse we toggle this default behviour when desired
	 */
	temp = read_aux_reg(ARC_REG_DC_CTRL);
	temp &= ~DC_CTRL_INV_MODE_FLUSH;

#ifdef CONFIG_ARC_HAS_DCACHE
	/* Enable D-Cache: Clear Bit 0 */
	write_aux_reg(ARC_REG_DC_CTRL, temp & ~IC_CTRL_CACHE_DISABLE);
#else
	/* Flush D cache */
	write_aux_reg(ARC_REG_DC_FLSH, 0x1);
	/* Disable D cache */
	write_aux_reg(ARC_REG_DC_CTRL, temp | IC_CTRL_CACHE_DISABLE);
#endif

	return;
}

#define OP_INV		0x1
#define OP_FLUSH	0x2
#define OP_FLUSH_N_INV	0x3

#ifdef CONFIG_ARC_HAS_DCACHE

/***************************************************************
 * Machine specific helpers for Entire D-Cache or Per Line ops
 */

static inline void wait_for_flush(void)
{
	while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS)
		;
}

/*
 * Operation on Entire D-Cache
 * @cacheop = {OP_INV, OP_FLUSH, OP_FLUSH_N_INV}
 * Note that constant propagation ensures all the checks are gone
 * in generated code
 */
static inline void __dc_entire_op(const int cacheop)
{
	unsigned long flags, tmp = tmp;
	int aux;

	local_irq_save(flags);

	if (cacheop == OP_FLUSH_N_INV) {
		/* Dcache provides 2 cmd: FLUSH or INV
		 * INV inturn has sub-modes: DISCARD or FLUSH-BEFORE
		 * flush-n-inv is achieved by INV cmd but with IM=1
		 * Default INV sub-mode is DISCARD, which needs to be toggled
		 */
		tmp = read_aux_reg(ARC_REG_DC_CTRL);
		write_aux_reg(ARC_REG_DC_CTRL, tmp | DC_CTRL_INV_MODE_FLUSH);
	}

	if (cacheop & OP_INV)	/* Inv or flush-n-inv use same cmd reg */
		aux = ARC_REG_DC_IVDC;
	else
		aux = ARC_REG_DC_FLSH;

	write_aux_reg(aux, 0x1);

	if (cacheop & OP_FLUSH)	/* flush / flush-n-inv both wait */
		wait_for_flush();

	/* Switch back the DISCARD ONLY Invalidate mode */
	if (cacheop == OP_FLUSH_N_INV)
		write_aux_reg(ARC_REG_DC_CTRL, tmp & ~DC_CTRL_INV_MODE_FLUSH);

	local_irq_restore(flags);
}

/*
 * Per Line Operation on D-Cache
 * Doesn't deal with type-of-op/IRQ-disabling/waiting-for-flush-to-complete
 * It's sole purpose is to help gcc generate ZOL
 */
static inline void __dc_line_loop(unsigned long start, unsigned long sz,
					  int aux_reg)
{
	int num_lines, slack;

	/* Ensure we properly floor/ceil the non-line aligned/sized requests
	 * and have @start - aligned to cache line and integral @num_lines.
	 * This however can be avoided for page sized since:
	 *  -@start will be cache-line aligned already (being page aligned)
	 *  -@sz will be integral multiple of line size (being page sized).
	 */
	if (!(__builtin_constant_p(sz) && sz == PAGE_SIZE)) {
		slack = start & ~DCACHE_LINE_MASK;
		sz += slack;
		start -= slack;
	}

	num_lines = DIV_ROUND_UP(sz, ARC_DCACHE_LINE_LEN);

	while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
		/*
		 * Just as for I$, in MMU v3, D$ ops also require
		 * "tag" bits in DC_PTAG, "index" bits in FLDL,IVDL ops
		 * But we pass phy addr for both. This works since Linux
		 * doesn't support aliasing configs for D$, yet.
		 * Thus paddr is enough to provide both tag and index.
		 */
		write_aux_reg(ARC_REG_DC_PTAG, start);
#endif
		write_aux_reg(aux_reg, start);
		start += ARC_DCACHE_LINE_LEN;
	}
}

/*
 * D-Cache : Per Line INV (discard or wback+discard) or FLUSH (wback)
 */
static inline void __dc_line_op(unsigned long start, unsigned long sz,
					const int cacheop)
{
	unsigned long flags, tmp = tmp;
	int aux;

	local_irq_save(flags);

	if (cacheop == OP_FLUSH_N_INV) {
		/*
		 * Dcache provides 2 cmd: FLUSH or INV
		 * INV inturn has sub-modes: DISCARD or FLUSH-BEFORE
		 * flush-n-inv is achieved by INV cmd but with IM=1
		 * Default INV sub-mode is DISCARD, which needs to be toggled
		 */
		tmp = read_aux_reg(ARC_REG_DC_CTRL);
		write_aux_reg(ARC_REG_DC_CTRL, tmp | DC_CTRL_INV_MODE_FLUSH);
	}

	if (cacheop & OP_INV)	/* Inv / flush-n-inv use same cmd reg */
		aux = ARC_REG_DC_IVDL;
	else
		aux = ARC_REG_DC_FLDL;

	__dc_line_loop(start, sz, aux);

	if (cacheop & OP_FLUSH)	/* flush / flush-n-inv both wait */
		wait_for_flush();

	/* Switch back the DISCARD ONLY Invalidate mode */
	if (cacheop == OP_FLUSH_N_INV)
		write_aux_reg(ARC_REG_DC_CTRL, tmp & ~DC_CTRL_INV_MODE_FLUSH);

	local_irq_restore(flags);
}

#else

#define __dc_entire_op(cacheop)
#define __dc_line_op(start, sz, cacheop)

#endif /* CONFIG_ARC_HAS_DCACHE */


#ifdef CONFIG_ARC_HAS_ICACHE

/*
 *		I-Cache Aliasing in ARC700 VIPT caches
 *
 * For fetching code from I$, ARC700 uses vaddr (embedded in program code)
 * to "index" into SET of cache-line and paddr from MMU to match the TAG
 * in the WAYS of SET.
 *
 * However the CDU iterface (to flush/inv) lines from software, only takes
 * paddr (to have simpler hardware interface). For simpler cases, using paddr
 * alone suffices.
 * e.g. 2-way-set-assoc, 16K I$ (8k MMU pg sz, 32b cache line size):
 *      way_sz = cache_sz / num_ways = 16k/2 = 8k
 *      num_sets = way_sz / line_sz = 8k/32 = 256 => 8 bits
 *   Ignoring the bottom 5 bits corresp to the off within a 32b cacheline,
 *   bits req for calc set-index = bits 12:5 (0 based). Since this range fits
 *   inside the bottom 13 bits of paddr, which are same for vaddr and paddr
 *   (with 8k pg sz), paddr alone can be safely used by CDU to unambigously
 *   locate a cache-line.
 *
 * However for a difft sized cache, say 32k I$, above math yields need
 * for 14 bits of vaddr to locate a cache line, which can't be provided by
 * paddr, since the bit 13 (0 based) might differ between the two.
 *
 * This lack of extra bits needed for correct line addressing, defines the
 * classical problem of Cache aliasing with VIPT architectures
 * num_aliases = 1 << extra_bits
 * e.g. 2-way-set-assoc, 32K I$ with 8k MMU pg sz => 2 aliases
 *      2-way-set-assoc, 64K I$ with 8k MMU pg sz => 4 aliases
 *      2-way-set-assoc, 16K I$ with 8k MMU pg sz => NO aliases
 *
 * ------------------
 * MMU v1/v2 (Fixed Page Size 8k)
 * ------------------
 * The solution was to provide CDU with these additonal vaddr bits. These
 * would be bits [x:13], x would depend on cache-geom.
 * H/w folks chose [17:13] to be a future safe range, and moreso these 5 bits
 * of vaddr could easily be "stuffed" in the paddr as bits [4:0] since the
 * orig 5 bits of paddr were anyways ignored by CDU line ops, as they
 * represent the offset within cache-line. The adv of using this "clumsy"
 * interface for additional info was no new reg was needed in CDU.
 *
 * 17:13 represented the max num of bits passable, actual bits needed were
 * fewer, based on the num-of-aliases possible.
 * -for 2 alias possibility, only bit 13 needed (32K cache)
 * -for 4 alias possibility, bits 14:13 needed (64K cache)
 *
 * Since vaddr was not available for all instances of I$ flush req by core
 * kernel, the only safe way (non-optimal though) was to kill all possible
 * lines which could represent an alias (even if they didnt represent one
 * in execution).
 * e.g. for 64K I$, 4 aliases possible, so we did
 *      flush start
 *      flush start | 0x01
 *      flush start | 0x2
 *      flush start | 0x3
 *
 * The penalty was invoking the operation itself, since tag match is anyways
 * paddr based, a line which didn't represent an alias would not match the
 * paddr, hence wont be killed
 *
 * Note that aliasing concerns are independent of line-sz for a given cache
 * geometry (size + set_assoc) because the extra bits required by line-sz are
 * reduced from the set calc.
 * e.g. 2-way-set-assoc, 32K I$ with 8k MMU pg sz and using math above
 *  32b line-sz: 9 bits set-index-calc, 5 bits offset-in-line => 1 extra bit
 *  64b line-sz: 8 bits set-index-calc, 6 bits offset-in-line => 1 extra bit
 *
 * ------------------
 * MMU v3
 * ------------------
 * This ver of MMU supports var page sizes (1k-16k) - Linux will support
 * 8k (default), 16k and 4k.
 * However from hardware perspective, smaller page sizes aggrevate aliasing
 * meaning more vaddr bits needed to disambiguate the cache-line-op ;
 * the existing scheme of piggybacking won't work for certain configurations.
 * Two new registers IC_PTAG and DC_PTAG inttoduced.
 * "tag" bits are provided in PTAG, index bits in existing IVIL/IVDL/FLDL regs
 */

/***********************************************************
 * Machine specific helpers for per line I-Cache invalidate.
 * 3 routines to accpunt for 1, 2, 4 aliases possible
 */

static void __ic_line_inv_no_alias(unsigned long start, int num_lines)
{
	while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
		write_aux_reg(ARC_REG_IC_PTAG, start);
#endif
		write_aux_reg(ARC_REG_IC_IVIL, start);
		start += ARC_ICACHE_LINE_LEN;
	}
}

static void __ic_line_inv_2_alias(unsigned long start, int num_lines)
{
	while (num_lines-- > 0) {

#if (CONFIG_ARC_MMU_VER > 2)
		/*
		 *  MMU v3, CDU prog model (for line ops) now uses a new IC_PTAG
		 * reg to pass the "tag" bits and existing IVIL reg only looks
		 * at bits relevant for "index" (details above)
		 * Programming Notes:
		 * -when writing tag to PTAG reg, bit chopping can be avoided,
		 *  CDU ignores non-tag bits.
		 * -Ideally "index" must be computed from vaddr, but it is not
		 *  avail in these rtns. So to be safe, we kill the lines in all
		 *  possible indexes corresp to num of aliases possible for
		 *  given cache config.
		 */
		write_aux_reg(ARC_REG_IC_PTAG, start);
		write_aux_reg(ARC_REG_IC_IVIL,
				  start & ~(0x1 << PAGE_SHIFT));
		write_aux_reg(ARC_REG_IC_IVIL, start | (0x1 << PAGE_SHIFT));
#else
		write_aux_reg(ARC_REG_IC_IVIL, start);
		write_aux_reg(ARC_REG_IC_IVIL, start | 0x01);
#endif
		start += ARC_ICACHE_LINE_LEN;
	}
}

static void __ic_line_inv_4_alias(unsigned long start, int num_lines)
{
	while (num_lines-- > 0) {

#if (CONFIG_ARC_MMU_VER > 2)
		write_aux_reg(ARC_REG_IC_PTAG, start);

		write_aux_reg(ARC_REG_IC_IVIL,
				  start & ~(0x3 << PAGE_SHIFT));
		write_aux_reg(ARC_REG_IC_IVIL,
				  start & ~(0x2 << PAGE_SHIFT));
		write_aux_reg(ARC_REG_IC_IVIL,
				  start & ~(0x1 << PAGE_SHIFT));
		write_aux_reg(ARC_REG_IC_IVIL, start | (0x3 << PAGE_SHIFT));
#else
		write_aux_reg(ARC_REG_IC_IVIL, start);
		write_aux_reg(ARC_REG_IC_IVIL, start | 0x01);
		write_aux_reg(ARC_REG_IC_IVIL, start | 0x02);
		write_aux_reg(ARC_REG_IC_IVIL, start | 0x03);
#endif
		start += ARC_ICACHE_LINE_LEN;
	}
}

static void __ic_line_inv(unsigned long start, unsigned long sz)
{
	unsigned long flags;
	int num_lines, slack;

	/*
	 * Ensure we properly floor/ceil the non-line aligned/sized requests
	 * and have @start - aligned to cache line, and integral @num_lines
	 * However page sized flushes can be compile time optimised.
	 *  -@start will be cache-line aligned already (being page aligned)
	 *  -@sz will be integral multiple of line size (being page sized).
	 */
	if (!(__builtin_constant_p(sz) && sz == PAGE_SIZE)) {
		slack = start & ~ICACHE_LINE_MASK;
		sz += slack;
		start -= slack;
	}

	num_lines = DIV_ROUND_UP(sz, ARC_ICACHE_LINE_LEN);

	local_irq_save(flags);
	(*___flush_icache_rtn) (start, num_lines);
	local_irq_restore(flags);
}

/* Unlike routines above, having vaddr for flush op (along with paddr),
 * prevents the need to speculatively kill the lines in multiple sets
 * based on ratio of way_sz : pg_sz
 */
static void __ic_line_inv_vaddr(unsigned long phy_start,
					 unsigned long vaddr, unsigned long sz)
{
	unsigned long flags;
	int num_lines, slack;
	unsigned int addr;

	slack = phy_start & ~ICACHE_LINE_MASK;
	sz += slack;
	phy_start -= slack;
	num_lines = DIV_ROUND_UP(sz, ARC_ICACHE_LINE_LEN);

#if (CONFIG_ARC_MMU_VER > 2)
	vaddr &= ~ICACHE_LINE_MASK;
	addr = phy_start;
#else
	/* bits 17:13 of vaddr go as bits 4:0 of paddr */
	addr = phy_start | ((vaddr >> 13) & 0x1F);
#endif

	local_irq_save(flags);
	while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
		/* tag comes from phy addr */
		write_aux_reg(ARC_REG_IC_PTAG, addr);

		/* index bits come from vaddr */
		write_aux_reg(ARC_REG_IC_IVIL, vaddr);
		vaddr += ARC_ICACHE_LINE_LEN;
#else
		/* this paddr contains vaddrs bits as needed */
		write_aux_reg(ARC_REG_IC_IVIL, addr);
#endif
		addr += ARC_ICACHE_LINE_LEN;
	}
	local_irq_restore(flags);
}

#else

#define __ic_line_inv(start, sz)
#define __ic_line_inv_vaddr(pstart, vstart, sz)

#endif /* CONFIG_ARC_HAS_ICACHE */


/***********************************************************
 * Exported APIs
 */

/* TBD: use pg_arch_1 to optimize this */
void flush_dcache_page(struct page *page)
{
	__dc_line_op((unsigned long)page_address(page), PAGE_SIZE, OP_FLUSH);
}
EXPORT_SYMBOL(flush_dcache_page);


void dma_cache_wback_inv(unsigned long start, unsigned long sz)
{
	__dc_line_op(start, sz, OP_FLUSH_N_INV);
}
EXPORT_SYMBOL(dma_cache_wback_inv);

void dma_cache_inv(unsigned long start, unsigned long sz)
{
	__dc_line_op(start, sz, OP_INV);
}
EXPORT_SYMBOL(dma_cache_inv);

void dma_cache_wback(unsigned long start, unsigned long sz)
{
	__dc_line_op(start, sz, OP_FLUSH);
}
EXPORT_SYMBOL(dma_cache_wback);

/*
 * This is API for making I/D Caches consistent when modifying code
 * (loadable modules, kprobes,  etc)
 * This is called on insmod, with kernel virtual address for CODE of
 * the module. ARC cache maintenance ops require PHY address thus we
 * need to convert vmalloc addr to PHY addr
 */
void flush_icache_range(unsigned long kstart, unsigned long kend)
{
	unsigned int tot_sz, off, sz;
	unsigned long phy, pfn;
	unsigned long flags;

	/* printk("Kernel Cache Cohenercy: %lx to %lx\n",kstart, kend); */

	/* This is not the right API for user virtual address */
	if (kstart < TASK_SIZE) {
		BUG_ON("Flush icache range for user virtual addr space");
		return;
	}

	/* Shortcut for bigger flush ranges.
	 * Here we don't care if this was kernel virtual or phy addr
	 */
	tot_sz = kend - kstart;
	if (tot_sz > PAGE_SIZE) {
		flush_cache_all();
		return;
	}

	/* Case: Kernel Phy addr (0x8000_0000 onwards) */
	if (likely(kstart > PAGE_OFFSET)) {
		__ic_line_inv(kstart, kend - kstart);
		__dc_line_op(kstart, kend - kstart, OP_FLUSH);
		return;
	}

	/*
	 * Case: Kernel Vaddr (0x7000_0000 to 0x7fff_ffff)
	 * (1) ARC Cache Maintenance ops only take Phy addr, hence special
	 *     handling of kernel vaddr.
	 *
	 * (2) Despite @tot_sz being < PAGE_SIZE (bigger cases handled already),
	 *     it still needs to handle  a 2 page scenario, where the range
	 *     straddles across 2 virtual pages and hence need for loop
	 */
	while (tot_sz > 0) {
		off = kstart % PAGE_SIZE;
		pfn = vmalloc_to_pfn((void *)kstart);
		phy = (pfn << PAGE_SHIFT) + off;
		sz = min_t(unsigned int, tot_sz, PAGE_SIZE - off);
		local_irq_save(flags);
		__dc_line_op(phy, sz, OP_FLUSH);
		__ic_line_inv(phy, sz);
		local_irq_restore(flags);
		kstart += sz;
		tot_sz -= sz;
	}
}

/*
 * Optimised ver of flush_icache_range() with spec callers: ptrace/signals
 * where vaddr is also available. This allows passing both vaddr and paddr
 * bits to CDU for cache flush, short-circuting the current pessimistic algo
 * which kills all possible aliases.
 * An added adv of knowing that vaddr is user-vaddr avoids various checks
 * and handling for k-vaddr, k-paddr as done in orig ver above
 */
void flush_icache_range_vaddr(unsigned long paddr, unsigned long u_vaddr,
			      int len)
{
	__ic_line_inv_vaddr(paddr, u_vaddr, len);
	__dc_line_op(paddr, len, OP_FLUSH);
}

/*
 * XXX: This also needs to be optim using pg_arch_1
 * This is called when a page-cache page is about to be mapped into a
 * user process' address space.  It offers an opportunity for a
 * port to ensure d-cache/i-cache coherency if necessary.
 */
void flush_icache_page(struct vm_area_struct *vma, struct page *page)
{
	if (!(vma->vm_flags & VM_EXEC))
		return;

	__ic_line_inv((unsigned long)page_address(page), PAGE_SIZE);
}

void flush_icache_all(void)
{
	unsigned long flags;

	local_irq_save(flags);

	write_aux_reg(ARC_REG_IC_IVIC, 1);

	/* lr will not complete till the icache inv operation is not over */
	read_aux_reg(ARC_REG_IC_CTRL);
	local_irq_restore(flags);
}

noinline void flush_cache_all(void)
{
	unsigned long flags;

	local_irq_save(flags);

	flush_icache_all();
	__dc_entire_op(OP_FLUSH_N_INV);

	local_irq_restore(flags);

}

/**********************************************************************
 * Explicit Cache flush request from user space via syscall
 * Needed for JITs which generate code on the fly
 */
SYSCALL_DEFINE3(cacheflush, uint32_t, start, uint32_t, sz, uint32_t, flags)
{
	/* TBD: optimize this */
	flush_cache_all();
	return 0;
}