projects / linux-2.6-block.git / blame
| Commit | Line | Data |
|---|---|---|
| 1da177e4 LT |
1 | README file for the Linux g_NCR5380 driver. |
| 2 | ||
| 3 | (c) 1993 Drew Eckhard | |
| 4 | NCR53c400 extensions (c) 1994,1995,1996 Kevin Lentin | |
| 5 | ||
| 6 | This file documents the NCR53c400 extensions by Kevin Lentin and some | |
| 7 | enhancements to the NCR5380 core. | |
| 8 | ||
| 9 | This driver supports both NCR5380 and NCR53c400 cards in port or memory | |
| 10 | mapped modes. Currently this driver can only support one of those mapping | |
| 11 | modes at a time but it does support both of these chips at the same time. | |
| 12 | The next release of this driver will support port & memory mapped cards at | |
| 13 | the same time. It should be able to handle multiple different cards in the | |
| 14 | same machine. | |
| 15 | ||
| 16 | The drivers/scsi/Makefile has an override in it for the most common | |
| 17 | NCR53c400 card, the Trantor T130B in its default configuration: | |
| 18 | Port: 0x350 | |
| 19 | IRQ : 5 | |
| 20 | ||
| 21 | The NCR53c400 does not support DMA but it does have Pseudo-DMA which is | |
| 22 | supported by the driver. | |
| 23 | ||
| 24 | If the default configuration does not work for you, you can use the kernel | |
| 25 | command lines (eg using the lilo append command): | |
| 9c41ab27 FT |
26 | ncr5380=addr,irq |
| 27 | ncr53c400=addr,irq | |
| 28 | ncr53c400a=addr,irq | |
| 29 | dtc3181e=addr,irq | |
| 1da177e4 LT |
30 | |
| 31 | The driver does not probe for any addresses or ports other than those in | |
| 32 | the OVERRIDE or given to the kernel as above. | |
| 33 | ||
| 34 | This driver provides some information on what it has detected in | |
| 35 | /proc/scsi/g_NCR5380/x where x is the scsi card number as detected at boot | |
| 36 | time. More info to come in the future. | |
| 37 | ||
| 1da177e4 LT |
38 | This driver works as a module. |
| 39 | When included as a module, parameters can be passed on the insmod/modprobe | |
| 40 | command line: | |
| 41 | ncr_irq=xx the interrupt | |
| 42 | ncr_addr=xx the port or base address (for port or memory | |
| 43 | mapped, resp.) | |
| 1da177e4 LT |
44 | ncr_5380=1 to set up for a NCR5380 board |
| 45 | ncr_53c400=1 to set up for a NCR53C400 board | |
| 9c41ab27 FT |
46 | ncr_53c400a=1 to set up for a NCR53C400A board |
| 47 | dtc_3181e=1 to set up for a Domex Technology Corp 3181E board | |
| 48 | hp_c2502=1 to set up for a Hewlett Packard C2502 board | |
| 1da177e4 LT |
49 | e.g. |
| 50 | modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1 | |
| 51 | for a port mapped NCR5380 board or | |
| 52 | modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1 | |
| 53 | for a memory mapped NCR53C400 board with interrupts disabled. | |
| 54 | ||
| 55 | (255 should be specified for no or DMA interrupt, 254 to autoprobe for an | |
| 56 | IRQ line if overridden on the command line.) | |
| 57 | ||
| 58 | ||
| 59 | Kevin Lentin | |
| 60 | K.Lentin@cs.monash.edu.au |